change wheel GREAT WALL PEGASUS 2006 User Guide

SA-7Suspension System and Automobile Axle
Alignment of Front Wheel
Alignment of Front Wheel (SF)
In case the outer tilt angle of front wheel or the back tilt angle
of kingpin fails to conform to the specified value, adjust the
cam forward or backward may amend them.
5. Wheel angel adjustment
Take apart the limit bolt cap of the steering knuckle to check
the inner wheel steering angle A.
The inner wheel steering angle: =32

Notice:The wheel should not touch the body brake hose
when the steering wheel is rotated to the bottom.
In case the max steering angle is not in the conformity with the
standard value, adjust the wheel angle through the limit bolts
of steering knuckle.
In case the wheel angle still fails to fall within the standard
range, make a inspection and change the weary and damaged
steering mechanism parts.
6. Wheel toe-in adjustment
Adjust the wheel toe-in according to the following approach
(a) Raise or reduce the vehicle until the suspension stands in
balance.
(b) Push the vehicle on the ground 5 meters forward under
the condition that the front wheels locate forward in a
line.front cam adjustment
rear cam adjustment
reduce increaseincrease reduce
A
B
A B
front

SA-12
6. Inspection and replacement for front brake disc
(a) Check the wear situation of the front brake disc. (see Dr
the brake caliper).
(b) Use the spanner to tear down the bolts that connect the
front wheel hub and the front brake disc.
(c) Connect the front wheel hub and the front brake disc with
bolt and spring washer, and screw up the bolts with a
moment spanner to the specified torque in the diagonal
order.
Fastening torque
(60-79)N
m
(d) Conduct the equilibrium test on the dynamic balancer,
the amplitude value displayed should not be larger than
13.5g under the condition that the measuring rotating
velocity is 796 r/m and the locking rotating velocity is
786 r/m, when the amplitude value is larger than 13.5 g,
encase the counter balanced clip, which is 4 g each, at the
corresponding phase, the number of the clip encased
should not be more than four.
7. Bearing outer race change
Press in the new bearing outer space with the special service
tools.
Notice: the bearing inner and outer races should be changed at
one time.
Assembly of Front Wheel Hub
1. Mount on the Bearing 32007 inner race and roller assem-
bly as well as the front wheel hub oil seal.
Coat the lithium base grease of (4-5)mm on the inner surfaces
of bearing outer race and the front wheel hub, encase the
Bearing 32007 inner race and roller assembly, plaster the
lubricant again. Coat a little lubricant on the lips of front wheel
hub oil seal and then tap it in place.
Notice: do not make the lubricant contact the front brake
disc face.
2. Mount on the Bearing 32007 inner race.
After coating the bearing outer race with the lithium base
grease of 4-5 mm, encase the inner race and roller assembly of
Bearing 30205, and plaster the lubricant again.
Suspension System and Automobile Axle (Dr/2WD)
Front Wheel Hub and Steering Knuckle (Front Wheel Hub)

SA-14
6. Tap in the front wheel hub with a rubber hammer
7. Mount the brake caliper on the steering knuckle.
Fastening torque
(85-105)N
m
Steering Knuckle
Disassembly of Steering Knuckle
1. Take apart the brake caliper, the front wheel hub and the
front brake disc.
2. Take apart the front brake shell:
(a) Tear down the two bolts (M8X16).
(b) Tear down the two split pins, grooved nuts, washer and
bolts that connect the steering knuckle arm.
3. Tear down the steering knuckle
(a) Support the lower arm with jack;
(b) Tear down the two split pins and the grooved nuts
(c) Disconnect the steering knuckle from the upper and
lower ball studs and take apart it.
Inspection on Steering Knuckle
Check the steering knuckle
Check the steering knuckle with the dye penetration agent to
see whether the steering knuckle has a crack or not.
If the crack is found, the steering knuckle is required to be
changed.
Suspension System and Automobile Axle (Dr/2WD)
Front Wheel Hub and Steering Knuckle (Front Wheel Hub)

SA-30
5. Front hub bearing outer race inspection and change
(a) Check each bearing
Wash the inner and outer races of each bearing, and check
them whether they are wearied or damaged.
(b) Tear down the outer race of each bearing.
Tap out the bearing outer race with copper bar and
hammer.
Notice: bind the dismantled inner and outer races of
bearing together to prevent from mixing.
6. Front brake disc inspection and change
(a) Check the wear situation of front brake disc.
(b) Tear down the bolts that connect the front wheel hub and
front brake disc.
(c) Connect the front wheel hub and front brake disc and
screw up the bolts with moment spanner to the specified
torque diagonally
Fastening torque
(70-80)N
m
(d) Conduct the dynamic balance test on the dynamic balancer,
the amplitude value displayed should not be above 13.5g
under the condition that the measuring rotating velocity
is 796 r/m and the locking rotating velocity 786 r/m,
otherwise, tap in the counter balanced clip, which is 4g
each, at the corresponding location, the number of the
clip should not be more than 4.
(e) Tap in the new bearing outer race with the special service
tool.
Notice: the inner and outer races of bearing should be
changed in set.
Assembly of Front Wheel Hub
1.Mount on the inner race and roller assembly of front hub
bearing (inner) as well as the front hub oil seal.
Coat the lithium base grease of 4 to 5 mm on the inside surface of
the bearing outer race and front wheel hub, and plaster the
lubricant in the front hub bearing (inner) and the roller assembly.
Coat a little lubricant on the lips of oil seal of front wheel hub, and
then tap the oil seal of front hub in place with special service tool.
Notice: do not coat the lubricant on the front brake disc face.
Suspension System and Automobile Axle (SF/2WD)
Front Wheel Hub and Steering Knuckle (Front Wheel Hub)

SA-34
7. Tear down the lower ball stud assembly from the steering
knuckle.
Inspection on and Change of Steering
Knuckle
1. Check the steering knuckle.
Check the steering knuckle with the dye penetration agent to
see whether there is crack or not.
If crack is found, the steering knuckle is required to be changed.
Mount of Steering Knuckle
1. Mount the lower ball stud on the steering knuckle.
Connect the lower ball stud and steering knuckle with bolts,
which are tightened according to the specified torque.
Fastening torque
(70-90)N
m
2. Mount on the steering knuckle
(a) Press down the lower arm to mount on the steering
knuckle.
(b) Mount on the lower ball stud, groove nut and screw up the
nuts according to the specified torque and then mount on
the split pin.
Fastening torque
(132-152)N
m
Suspension System and Automobile Axle (SF/2WD)
Front Wheel Hub and Steering Knuckle (Steering Knuckle)

SA-46
5. Tear down the front hub, the oil seal and the inner race
of front hub bearing (inner)
(a) Prize out the oil seal.
(b) Take out the inner race of front hub bearing (inner).
6. Inspection on and change of the outer race of front hub
bearing
(a) Check each bearing:
Wash the inner and outer races of each bearing to check
their wear or damage situation.
(b) Tear down the outer race of each bearing:
Tap out the outer bearing race with copper bar and hammer.
Notice: bind the inner and outer races of the same
bearing together to prevent from mixing.
7. Inspection and change for front brake disc
(a) Check the wear situation of the front brake disc.
(b) Tear down the bolts that connect the front wheel hub and
the front brake disc.
(c) Connect the front wheel hub and the front brake disc with
bolts, which are tightened diagonally with moment span-
ner according to the specified torque.
Fastening torque
(70-80)N
m
(d) Make the dynamic balance test on the dynamic balancer,
and the amplitude value displayed should not be smaller
than 13.5g under the condition that the measuring rotat-
ing velocity is 796 r/m and the locking rotating velocity
of 786 r/m, otherwise, tap the counter balanced clip,
which is 4g each, in the corresponding position, the clip
number should not be more than 4.
(e) Tap in the new bearing outer race carefully with the
special service tool.
Notice: the inner and outer races of the same bearing
should be changed in one time.
Suspension System and Automobile Axle (SF/4WD)
Front Wheel Hub and Steering Knuckle (Front Wheel Hub)

SA-50
(c) Tear down the split pin and groove nut from the position
where the lower ball stud.
(d) Tear down the steering knuckle from the position where
the lower ball stud with the special service tool, and
(e) Press down the lower arm to tear down the steering
knuckle.
7. Tear down the Lower ball stud assembly from the posi-
tion where the steering knuckle locates.
Steering knuckle inspection and change
Inspection on and Change of Steering
knuckle
1. Check the steering knuckle
Check the steering knuckle with the dye penetration agent to
see weather has crack, if any crack is found, change the
steering knuckle.
2. Tear down the inner oil seal

drive shaft and the thrust
plate

steering knuckle.
Prize out the inner oil seal

drive shaft from the steering
knuckle with the screwdriver to take out the thrust plate


steering knuckle.
Suspension System and Automobile Axle(SF/4WD)
Front Wheel Hub and Steering Knuckle (Steering Knuckle)

SA-52
8. Mount the inner oil seal óon the steering knuckle.
Check the oil seal visually, if any deformation or glue lack is
found, change the oil seal
Mount of Steering Knuckle
1. Mount the lower ball stud on the steering knuckle;
Connect the lower ball stud and the steering knuckle with
bolts, and screw up the bolts according to the specified torque.
Fastening torque
(70-90)N
m
2. Mount on the steering knuckle
(a) Coat the lubricant HP-R on the drive shaft.
(b) Press down the lower arm to mount on the steering
knuckle.
(c) Mount on the groove nut of lower ball stud and screw up
the nut according to the specified torque, and then mount
on the split pin.
Fastening torque
(132-152)N
m
(d) Mount on the groove nut of upper ball stud and screw up
the nut according to the specified torque, and then mount
on the split pin.
Fastening torque
(132-152)N
m
Suspension System and Automobile Axle (SF/4WD)
Front Wheel Hub and Steering Knuckle (Steering Knuckle)

SA-57
1. Support up the front of vehicle to tear down the front
wheel and the steering knuckle.
2. Drain off lubricant in the front speed reducer.
3. Disconnect the front speed reducer flange and the drive
shaft.
Notice: Mark the assembly marks on the speed reducer
and the drive shaft before disconnecting them.
4. Tear down the front speed reducer.
5. Tear down the flange and dust cover:
(a) Loosen the riveted position on main-tooth nut with the
hammer and chisel.
Front Speed Reducer
Change of driving bevel gear oil seal of front speed reducer
front speed reducer and
differential assembly
oil-guard tray

driving bevel gear oil seal
flange and dust cover
140-210


Parts that cannot be reused after being used
specified torque
N
M
main-tooth nut
Suspension System and Automobile Axle (SF/4WD)
Front Speed Reducer (Change of Driving Bevel Gear Oil Seal of Front Speed Reducer)

SA-80
Dismantle of Rear half Axle Shaft
1. Tear down the wheels.
2. Tear down the rear brake drum.
3. Tear down the grab end of the bracing wire of hand brake
from the rear brake.
4. Tear down the half-shaft and the rear brake assembly
from the rear axle housing.
5. Tear down the flat steel retainer ring for shaft from the
half-shaft;
Tear down the flat steel retainer ring for shaft with the ring
calipers.
6. Tear down the half-shaft:
Put down a wooden plate on the flat ground, and thrust the end
of spline of half-shaft and rear brake assembly toward the
wooden plate to separate the shaft and the rear brake assembly.
Inspection on and repairing of half-shaft parts
1. Check the wear, damage and swing difference half-shaft
and the flange.
Max shaft run-out: 2 mm
Max flange run-out: 0.2 mm
In case the half-shaft is damaged, or wearied or the measuring
value of the swing difference is excessive, change the half-
shaft.
2. Check he oil seal of rear wheel bearing:
Check to see whether there is wear or damage, and change the
oil seal if necessary.
3. The disassembly of the outer oil seal of rear wheel
bearing;
Tear down the outer oil seal of rear wheel bearing with SST. Suspension System and Automobile Axle (rear)
Rear Half Axle Shaft