change wheel GREAT WALL PEGASUS 2006 Owner's Manual

SA-81
4. Check the grooved ball bearing
Check the grooved bearing to see whether there is damage or
wear.
5. Change the bearing where necessary:
(a) Press out the grooved ball bearing with SST.
(b) Press in the new grooved ball bearing with SST.
6. Mount the new oil seal of rear wheel bearing.
Press in the new oil seal of rear wheel bearing with SST
Coat moderate lithium base grease on the lip open of oil seal.
7. Check the bearing seat.
Check the wear or damage situation.
8. Change the bearing seat where necessary:
(a) Tear down the oil seal of rear wheel bearing and the
grooved ball bearing with SST.
(b) Tap the bolts with copper bar to tear down the bearing seat.
(c) Mount the new grooved ball bearing and the oil seal of
rear wheel bearing on the bearing seat
(d) Press the rear brake, which is put on with bolts, in the
bearing seat.
9. Check the wear or damage of the inner oil seal of the rear
wheel bearing.
10. Change the rear wheel bearing where necessary:
(a) Tear down the oil seal of rear wheel bearing with SST. Suspension System and Automobile Axle (rear)
Rear half Axle Shaft

SA-94
Mount of Rear Speed Reducer and
Differential Assembly
1. Mount the speed reducer and differential assembly on
the rear axle housing.
Tightening moment
(18-26)N
m
Remark: in case the sealing gasket is mounted, it should be
checked to see whether it is damaged before mounting, if
damaged, change with the new sealing gasket, and the dam-
aged sealing gasket should be clear away; if no sealing gasket
is mounted, no mount is required to mount. Clean the contact
face of the mounted axle housing and coat it with silicon-
rubber plain sealing agent.
2. Connect the drive shaft and flange well and be careful to
align the assembly marks marked when disassembling.
Tightening moment
(69-79)N
m
Screw up the oil drain plug with the Tightening moment
of (140-150)N
m
Mount on the half-shaft and the brake assembly to adjust the
brake oil path so that the wheel brake pump is filled with brake
liquid.
3. Inject in the heavy-duty oil.
Oil brand: heavy-duty oil graded GL-5;
Viscosity: SAE 85W/90
Oil volume: add the oil until it overflows from the oil filler
outlets.
Screw up the oil-filling plug.
Tightening moment
(140-150)N
m
Suspension System and Automobile and Axle (Rear)
Rear speed reducer (Mount of Rear Speed Reducer and Differential Assembly)

BR-2Braking System
Notice and Troubleshooting
Notice:
1. Carefully change each part where necessary because any
mistake will affect the brake system properties, and will lead
accidents during driving. And the parts to be changed must
be the same in part number or equal in quality.
2. Keep the parts and each position clean when repairing the
braking system.
Troubleshooting
Trouble Causes Inspection items
Lower or soft pedal Abrasion of brake shoe
Abrasion of brake pad
Oil leakage of braking system
Master cylinder failure
Air in braking system
Wheel-brake cylinder failure
Failure in the automatic regulator of rear brake.Change the brake shoe; Change the brake
pad;
Repair the oil leakage;
Change the master cylinder;
Drain out the air from braking system;
Change the wheel-brake cylinder;
Repair or change the regulator
Brake stagnantPoor adjustment of parking brake;
The bracing wire of parking brake is seized;
Poor adjustment of vacuum booster pushrod)
Failure of the drag spring or the return spring
Pipe line blockage
Brake shoe breakage or deformation
Brake pad breakage or deformation
Seizing of the wheel-brake cylinder or the brake
caliper piston
Automatic regulator breakage
Master cylinder failureAdjust the parking brake;
Make repairing according to real situation;
Adjust the drag rod;
Change the drag spring or the return spring
Make repairing according to real situation;
Change the brake shoe
Change the brake pad
Make repairing according to real situation;
Change the regulator
Change the master cylinder
Over large braking
distanceUnsuitable tire inflation
There is oil stain or lubricant on the brake shoe or
brake pad;
Brake shoe deforms, the brake liner is worn or polished;
Brake pad deforms or is worn or polished;
Brake drum or brake disc deforms
Drag spring or return spring has trouble
The wheel-brake cylinder has trouble
The inner piston of wheel-brake cylinder is seized;
The brake pad is seized;Inflate the air to suitable pressure;
Change the brake shoe or the brake pad;
Change the brake shoe;
Change brake pad
Change the brake drum or the brake disc;
Change the spring;
Change the wheel-brake cylinder;
Change the wheel-brake cylinder
Change the brake pad
The brake pedal is hard
but doesn
t work;There is oil stain or lubricant on the brake shoe or
brake pad;
The brake shoe deforms, brake liner is worn or
polished, or the brake wheel is worn;
The brake pad deforms, or is worn or polished;
The piston of wheel brake pump is seized;
The vacuum booster has trouble
The vacuum degree is unsuitable
The brake pipe line is blockedChange the brake shoe brake pad;
Change the brake shoe
Change the brake pad;
Change the wheel-brake cylinder;
Change the vacuum booster;
Make repairing according to real situation;
Make repairing according to real situation;

BR-3
Troubleshooting (continued)
Braking System
Notice and Troubleshooting
Trouble Causes Inspection items
There is clatter noise when using
the brake(Drum-type brake)
The brake shoe is seized on the flange of rear baffle;
The flange of rear baffle is worn;
The pressure spring of brake shoe is loose or missing;
The fixed bolts of brake bottom plate is loose;
(disc type brake)
The brake pad support plate is loose or missing
The mounting bolts are loose;Add lubricant
Change the lubricating flange
Change
Tightening it
Change
Tightening it
There is hoarse noise or quack-
quack when using the brakeThe brake shoe or brake pad is worn;
The brake caliper, the wheel or the rotator interferes each
other.
There is friction between the dust cover and brake disc,
the brake bottom plate and the brake drum;
The other braking part has trouble
There is friction between the tire and bodyChange the part, and re-process
precisely the brake drum or
rotator if the abrasion is serious;
Make change according to real
situation;
repair or change
Make repairing according to
real situation;
Change
Check or maintain the part
There is such noise as
continuous screaming, quack-
quack, oscillating sound, etc.
Notice: the braking materials
may generate the natural noise
and heat during friction, and
thus emit the energy. Therefore,
it is normal to have the
screaming noise. These
phenomena will be more serious
under the condition of frigidity,
torridity, and over humidity,
snowing and mud. the
screaming noise occurring
occasionally will not lead the
fatal brake trouble nor reduce
the effective properties of the
brake.The brake drum, brake liner, liner or brake pad is worn
or scraped
The brake liner or brake pad is dirty or with oil stain or
polished.
The brake liner or brake pad is improperly used.
The brake pedal or vacuum booster drag rod is unsuitably
adjusted.
(disc type brake)
The brake pad silent pad is loss or damaged;
The brake pad is worn to the degree that the abrasion-
indicating lamp of brake pad has friction with the rotator.
There is burr or rust on the brake caliper.
(Drum type brake)
The pressure spring of brake shoe is soft in rigidity, or is
damaged or unsuitable.
The pressure spring pin or spring of brake shoe is loose
or damaged;
There is crack on the brake bottom plate flangeCheck, repair or change
Clean or change
Check or change
Check for adjustment
Change
Change
Clean or polish the burr
Check, repair or change
Check, repair or change
Check, repair or change

BR-4Braking System
Notice and Troubleshooting
Troubleshooting (continued)
Trouble Causes Inspection items
There are quack-
quack noises
without using the
brake.Alien materials such as stone is reeled inside the wheel shell
Nuts on hub is loose;
The brake pedal or vacuum booster pushrod is adjusted
improperly;
The wheel bearing is worn or damaged or lubricated
insufficiently;
(disc type brake)
The outer end edge of brake pad support plate or brake pad
is dog-eared;
The silent pad is poor in properties;
The sliding liner is worn;
The mounting bolt is loose
The piston returns incompletely
(drum type brake)
There is loose or redundant part.Clear away the alien materials
Tighten the nut to the specified torque; and
change it in case the bolt hole is enlarged;
Check and adjust
Check, lubricate or change
Check repair or change
Check and make change according to real
situation
Check and make change according to real
situation
Check and tighten according to the necessity.
Check, repair or change
Check, take out or repair.
There is continuous
screaming noise
without using brakeThe brake pedal or vacuum booster pushrod is adjusted
improperly
The vacuum booster, master cylinder or wheel-brake cylinder
returns incompletely.
(Disc type brake)
The piston is rusted or seized;
The brake pad in brake caliper locates improperly;
There is friction between the brake disc and brake caliper
shell;
The brake pad support plate is mounted improperly;
There is interference between the abrasion indicating lamp
of brake pad and the brake disc due to the brake pad
abrasion;
(Drum type brake)
The pressure spring of brake shoe is soft rigidity, damaged
or unsuitable;
There is crack on the brake bottom plate flange;
There is interference of brake bottom plate with the brake
drum after it is bending or warping.
The brake drum interferes with the brake bottom plate or
with brake shoe due to it is processed improperly;
Other brake parts

There is loose or redundant part in braking system;
The brake liner is polished due to it is adjusted over-tightly;
The wheel bearing is worn, damaged or lubricated
insufficiently.Check and adjust
Check, repair or change
Check and add the lubricant according to
the necessity;
Repair or change
Repair or change
Repair or change
Change
Change
Repair or change
Repair or change
Change the brake drum
Check, maintain and change according to
the necessity;
Check, maintain and change according to
the necessity;
Check, maintain and change according to
the necessity;

BR-6
Operation test of vacuum booster
Remark: check the operation of vacuum booster with the
vacuum booster tester if workable.
1.Operation inspection
(a) Before starting the engine, tread down the brake pedal
several times, and check the pedal reservation distance to
ensure there is no change occurs.
(b) Tread down the brake pedal and start the engine. If the
treaded pedals continue to move downward, which means
the operation is normal.
1. Inspection on Air-tight
(a) Start the engine for 1-2 min and then turn it off. Then
tread down the brake pedal slowly for several times, if the
pedal move downward continuously in the first, but
return gradually in the second or third time, which means
the vacuum booster has a good air-tight.
(b) Tread down the brake pedal when the engine is working,
then stop the engine, but tread the pedal down. If the
reservation distance doesnít change within the 30 seconds,
which shows the air tight of vacuum booster is good.
Air-bleeding of braking system
Remark: air-bleeding is required if any operation for braking
system is conducted or the pipe line is doubted to have air.
1. Fill the oil cup with the brake liquid
Check the liquid level of oil cup after the air in each wheel
brake pump is exhausted. If necessary, add the brake liquid.
2. Connect the vinyl resin pipe with the vent screws.
Insert the other end of pipe into the container with half brake
liquid.
Remark: the air-bleeding shall begin from the longest pipe line
when the wheel-brake cylinder is exhausting the air.
3. Air exhaust of the pipe line in braking system
(a) Tread down brake pedal slowly several times.
(b) Loosen the vent screws until the brake liquid flows out
while letting the assistant tread down the pedal. Then
screw up the vent screws.
(c) Repeat this approach until there is no air in the liquid.
4. Repeat the approach for the wheel-brake cylinder.
normal
abnormal
the third time
the second time
the first time
Braking System
Inspection and Adjustment

BR-14
Brake pad change
Remark: Check the thickness of the friction material of brake
pad through the observation hole on caliper body after the
vehicle covers thirty thousand; if the thickness fails to fall
within the specified range, change is required. (If the brake is
used often, the thickness of friction materials of brake
pad is required to check whether it is within the specified
range after the vehicle covers more than ten thousand,
if not, change it.
1. Tear down the front wheel;
2. Check the thickness of friction material of brake pad:
Check the thickness of friction material of brake pad through
the observation hole on caliper body, if it fails to be within the
specified range, change it.
Min thickness: 2.0mm
3. Raise the wheel-brake cylinder:
(a) Tear down the short bolts of sliding sleeve;
(b) Uplift the wheel brake pump and hang it with rope to
protect the brake oil pipe.
Remark: Do not loosen the brake oil pipe and the bleeding plug.
4. Tear down the following parts:
(a) Two braking pads;
(b) Two silent pad clusters;
(c) Four braking pad lock plates.
Braking System
Front Brake (Dr)

BR-15
5. Brake disc measurement
(See page BR-17)
6. Measure the radial run-out of the brake disc;
(See BR-18)
7. Mount the lock plate of brake pad.
8. Mount the new brake pad.
(a) Mount the silent pad cluster on brake pads of both the
inner and outer sides;
Remark: Pollution of oil stain or coat is not allowed on the
work faces of brake pad or brake disc.
(b) Draw out a little brake liquid from the liquid container to
prevent the brake liquid overflowing from the liquid
container;
(c) Press in the piston with the hammer lever or similar tool.
9. Mount the wheel-brake cylinder;
Mount and screw up the hex bolts (the hex bolts shall be coated
with the thread locking sealing agents.
Fastening torque
(38-50)N
m
Remark: only one brake pad can be changed in one time so as
to prevent the piston of other wheel being shot out.
Braking System
Front Brake (Dr)

BR-17
2. Tear down the piston dust cover snapping ring and the
piston dust cover;
Tear down the piston dust cover snapping ring and the piston
dust cover with screwdriver.
3. Tear down the piston from the wheel-brake cylinder:
(a) Put a wooden plate between the piston and the caliper
body.
(b) Tear down the piston from wheel-brake cylinder with the
compressed air.
Warning: Do not put your finger in front of the piston when
using the compressed air.
4. Tear down the piston sealing ring from the caliper body.
Tear down the piston sealing ring with bent needle.
Notice: the tools used shall not be sharp so as not to
scrape the piston sealing ring.
Check the front brake parts
1. Measure the thickness of brake pad liner;
Standard thickness
10.0mm
Min thickness
2.0mm
If the thickness is less than the min thickness or is unevenly
worn; change the brake pad.
2. Measure thickness of brake disc
Standard thickness
25.0mm
Min thickness
23.0mm
If the brake disc is scraped, repair it, if the brake is serious
worn to the degree that its thickness is less than the min thickness,
brake disc requires to be changed Braking System
Front Brake (Dr)

BR-18
3. Measure the bouncing value of the brake disc face;
Remark: verify the bearing is aligned correctly before
measuring.
The bouncing value of max face: 0.11mm
4. Change the brake disc according to the requirements
(a) Tear down the calipers body from the steering knuckle.
(b) Tear down the hub and the brake disc (See Page SA-11).
(c) Mount the new brake disc and screw up the connecting
bolts according to the specified torque.
Fastening torque
(60
79)N.m
(d) Mount the hub and brake disc assembly (see page SA-12);
(e) Mount the caliper bracket on the steering knuckle and
screw up the bolts according to the specified torque.
Fastening torque
(85
105)N.m
Cylinder Assembly of Wheel-brake
1. Preparation
All parts shall be washed, dried and cleared away the alien
materials before the assembly. And coat moderate vacuum
silicon base grease on the work faces of sliding sleeve dust
cover, sliding sleeve and the sliding liner; and plaster the
moderate rubber lubricant on the work faces of piston, piston
dust cover and the rectangular sealing ring.
2. Encase the piston sealing ring and piston in the caliper body;
(a) Screw the vent screw in the vent hole of calipers.
Fastening torque
(8
13)N.m
(b) Coat moderate rubber lubricant on the work face rectan-
gular sealing ring and encase the caliper body in groove.
(c) Encase the piston in the caliper body.
3. Encase the piston dust cover and the dust cover
snapping ring in the wheel-brake cylinder.
Braking System
Front Brake (Dr)