lock HONDA ACCORD 2010 8.G Technology Reference Guide

Indicators/Info Display/TPMS
Instrument Panel Indicators
Briefly appear with each engine start. Red and amber indicators are most critical. Blue and green indicators are used for general information.
ABS (anti-lock brake system)
DRL (daytime running lights)
Malfunction lamp (check engine light)
TPMS (tire pressure monitoring system)
VSA (vehicle stability assist)
Malfunction Indicators:If an indicator remains on, there may be a problem; see your dealer.
Charging system
Low oil pressure
SRS (supplemental restraint system)
Low brake fluid
10 Accord TRG 4D_Inside Front:Inside Cvr 4/6/2009 9:48 AM Page 1

Auto Door Locks/HomeLink®
Auto Door Locking/Unlocking
Default Lock Setting
Modifying the Auto Door Unlock Setting
The doors are preset to lock when your vehiclereaches about 9 mph.
Default Unlock Setting
Only the driver’s door is preset to unlockwhen you shift intoPark (P).
Follow these steps to program all doors to unlock when you shift to Park:
1. Closethe driver’s door. Turnignition to the ON (II)position.
See Auto Door Locking/Unlockingin your owner’s manual for other programmable settings.
2. Make surethe shift lever is inPark.
3. Press and holdthe unlock side of the master lock switch for about 10seconds or until you hear a thirdclick.
4. Within 5 seconds, turn the ignition to the LOCK(0) position.
10 Accord TRG 4D_Base:Base 4/6/2009 9:48 AM Page 3

Auto Door Locks/HomeLink®
HomeLink®(EX-L V6)
Press and hold the button on the remote and the HomeLink button at the same time. Then, while continuing to hold the HomeLink button, press and release the button on the remote every 2 seconds.Does the LED blink at a faster rate within 20 seconds?
Press and hold the HomeLink button again.
Training complete
YES NO
HomeLink indicator flashes for 2 seconds, then remains on.
HomeLink LED remains on.YES NO
YES NO
Position the remote transmitter you wish to link 1–3 inches from the HomeLink button you want to program.
1
Press and hold the desired HomeLink but ton and the button on the remote transmitter.Does the HomeLink indicator (LED) blink at a faster rate after about 10 seconds?
2
aThe remote has a rolling code. Press the “learn” button on the remote-controlled device (e.g., garage door opener).
Press the programmed HomeLink button again; the remote-controlled device should operate.
Within 30 seconds, press and hold the programmed HomeLink button for 2 seconds.
a
Press and hold the programmed HomeLink button for about a second.Does the device (garage door opener) work?
3
b
4
5
Training a Button
Indicator remains on for about 25 seconds (standard transmitter).
Indicator flashes rapidly for 2 seconds, then remains on for about 23 seconds (rolling code transmitter).
Press and hold the desired HomeLink button until the HomeLink indicator begins to flash slowly.
When the indicator begins to flash slowly, continue to hold the HomeLink button and follow steps 1– 4 under Training a Button.
1
2
Retraining a Button
Erasing CodesTo erase codes stored in all buttons, press and hold the two outer buttons until the HomeLink indicator begins to flash (about 10 to 20 seconds), then release the buttons.
If you have any problems programming HomeLink, see the owner's manual included with the device you are trying to program, call HomeLink at (800) 355-3515 or visit www.homelink.com.
If you sell the vehicle, make sure to erase all codes.
The HomeLink Universal Transceiver built into your vehicle can be programmed to operate up to three remote-controlled devices around your home, such as garage doors, lighting, or home security systems.
10 Accord TRG 4D_Base:Base 4/6/2009 9:48 AM Page 4