check engine HONDA ACCORD HYBRID 2017 9.G Owners Manual
[x] Cancel search | Manufacturer: HONDA, Model Year: 2017, Model line: ACCORD HYBRID, Model: HONDA ACCORD HYBRID 2017 9.GPages: 584
Page 19 of 584

18
Quick Reference Guide
Safe Driving (P 33)
Airbags (P 45)
● Your vehicle is fitted with ai rbags to help protect you and 
your passengers during a moderate-to-severe collision.
Child Safety (P 58)
● All children 12 and younger should be seated in the rear seat.
● Smaller children should be properly restra ined in a forward-facing child seat.
● Infants must be properly restraine d in a rear-facing child seat.
Exhaust Gas Hazard (P 70)
● Your vehicle emits dangerous exhaust gases that contain carbon 
monoxide. Do not run the engine in confined spaces where carbon 
monoxide gas can accumulate.
Before Driving Checklist (P 37)
● Before driving, check that the  front seats, head restraints, 
steering wheel, and mirrors have been properly adjusted.
Seat Belts (P 38)
● Fasten your seat belt and sit upright well 
back in the seat.
● Check that your passengers are wearing 
their seat belts correctly.
Fasten your lap belt as 
low as possible.
17 ACCORD FHEV-31T3W6200.book  18 ページ  2016年4月11日 月曜日 午後2時40分 
Page 30 of 584

29
Quick Reference Guide
Maintenance (P 485)
Under the Hood (P 493)
● Check engine oil, engine coolant, inverter coolant, and 
windshield washer fluid. Add when necessary.
● Check brake fluid.
● Check the 12-volt battery condition monthly.
aPull the hood release handle under the corner of the 
dashboard.
bLocate the hood latch lever, pull the lever up, and lift up 
the hood.
cWhen finished, close the hood  and make sure it is firmly 
locked in place.
Lights (P 506)
● Inspect all lights regularly.
Wiper Blades (P 514)
● Replace blades if they leave streaks 
across the windshield.
Tires (P 516)
● Inspect tires and wheels regularly.
● Check tire pressures regularly.
● Install snow tires for winter 
driving.
17 ACCORD FHEV-31T3W6200.book  29 ページ  2016年4月11日 月曜日 午後2時40分 
Page 76 of 584

75
uuIndicators u
Continued
Instrument Panel
IndicatorNameOn/BlinkingExplanationMessage
POWER 
SYSTEM 
Indicator
●Comes on for a few seconds when 
you set the power mode to ON, 
then goes off.
●Comes on if there is a problem 
with the electric vehicle system.
●Comes on when the High Voltage 
battery temperature becomes high 
while the battery is being charged.
●Have your vehicle checked by a dealer.
READY Indicator
●Comes on for a few seconds when 
you set the power mode to ON, 
then goes off.
●Comes on when the vehicle is 
ready to drive.
2Turning on the Power  P. 416
EV Indicator
●Comes on for a few seconds when 
you set the power mode to ON, 
then goes off.
●Comes on when the vehicle is 
moved by the motor, and the 
engine is not operating.——
EV Mode 
Indicator
●Comes on for a few seconds when 
you set the power mode to ON, 
then goes off.
●Comes on when the vehicle is in EV 
mode.
2 SPORT HYBRID i-MMD 
(intelligent Multi Mode 
Drive)  P. 10
—
17 ACCORD FHEV-31T3W6200.book  75 ページ  2016年4月11日 月曜日 午後2時40分 
Page 77 of 584

76
uuIndicators u
Instrument Panel
IndicatorNameOn/BlinkingExplanationMessage
Low Oil Pressure 
Indicator
●Comes on for a few seconds when 
you set the power mode to ON, 
then goes off.
●Comes on when the engine oil 
pressure is low.
●Comes on while driving  - Immediately 
stop in a safe place.
2 If the Low Oil Pressure Indicator 
Comes On  P. 554
Malfunction 
Indicator Lamp
●Comes on when you set the power 
mode to ON, and  goes off either 
when the power system is on or 
after several seconds if the vehicle 
did not start. If “readiness codes” 
have not been set, it blinks five 
times before it goes off.
●Comes on if there is a problem 
with the emissions control system.
●Blinks when a misfire in the 
engine's cylinders is detected.
●Readiness codes are part of the on board 
diagnostics for the  emissions control 
systems.
2 Testing of Readiness Codes  P. 569●Comes on while driving - Have your 
vehicle checked by a dealer.
●Blinks while driving  - Stop in a safe 
place where there are no flammable 
objects. Stop the power system for 10 
minutes or more, and wait for the engine 
to cool down. Then, take the vehicle to a 
dealer.
2 If the Malfunction Indicator Lamp 
Comes On or Blinks  P. 555
12-Volt Battery 
Charging System 
Indicator
●Comes on when you set the power 
mode to ON, and goes off when 
the power system is on.
●Comes on when the 12-volt 
battery is not charging.
●Comes on while driving  - Turn off the 
climate control system and rear defogger 
in order to reduce electricity 
consumption.
2 If the 12-Volt Battery Charging 
System Indicator Comes On  P. 554
17 ACCORD FHEV-31T3W6200.book  76 ページ  2016年4月11日 月曜日 午後2時40分 
Page 98 of 584

97
uuIndicators uMulti-Information Display Warning and Information Messages
Instrument Panel
MessageConditionExplanation
●Appears if the power system is in diagnostic mode.●You may notice a decrease in available power. Have your 
vehicle checked by a dealer.
●As a result of diagnostics, the  POWER SYSTEM 
indicator may come on.
2 POWER SYSTEM Indicator  P. 75
●Appears when you failed to select EV mode or EV 
mode is automatically canceled.
●The cause may be shown with the following 
message:
- Ambient Temperature Too Low
- Battery Charge Too Low
- Engine Too Cold
- Cabin Being Heated
- Speed Too High
- Hard Acceleration Requested
●EV mode is available once th e condition is improved or 
the cause that canceled EV mode is cleared.
17 ACCORD FHEV-31T3W6200.book  97 ページ  2016年4月11日 月曜日 午後2時40分 
Page 411 of 584

410
Driving
Before Driving
Driving Preparation
Check the following items before you start driving.
• Make sure there are no obstructions on th e windows, door mirrors, exterior 
lights, or other parts of the vehicle.
u Remove any frost, snow, or ice.
u Remove any snow on the roof, as this can slip down and obstruct your field of 
vision while driving. If frozen solid , remove ice once it has softened.
u When removing ice from around the wheel s, be sure not to damage the wheel 
or wheel components.
• Make sure the hood is securely closed.
u If the hood opens while driving, your front view will be blocked.
• Make sure the tires are in good condition.
u Check air pressure, check for damage and excessive wear.
2 Checking and Maintaining Tires  P. 516
•Make sure there are no people or ob jects behind or around the vehicle.
u There are blind spots from the inside.
■Exterior Checks1Exterior Checks
NOTICE
When doors are frozen s hut, use warm water around 
the door edges to melt any ice. Do not try to force 
them open, as this can damage the rubber trim 
around the doors. When done, wipe dry to avoid 
further freezing.
Do not pour warm water  into the key cylinder.
You will be unable to insert the key if the water 
freezes in the hole.
Heat from the engine  and exhaust can ignite 
flammable material s left under the hood, causing a 
fire. If you've parked y our vehicle for an extended 
period, inspect and remove  any debris that may have 
collected, such as dried grass and leaves that have 
fallen or have been carried  in for use as a nest by a 
small animal. Also check  under the hood for leftover 
flammable materials after  you or someone else has 
performed maintenance on your vehicle.
17 ACCORD FHEV-31T3W6200.book  410 ページ  2016年4月11日 月曜日 午後2時40分 
Page 417 of 584

416
Driving
When Driving
Turning on the Power
1.Make sure the parking brake is applied.
2. Check that the shift lever is in 
(P, then 
depress the brake pedal.
u Although it is possibl e to start the vehicle 
in 
(N, it is safer to start it in (P.
1 When Driving
When you set the power mode to ON, you may feel 
as if the brake pedal is sinking down. This is normal.
1Turning on the Power
Keep your foot firmly on the brake pedal when 
starting the power system.
The engine is harder to st art in cold weather and in 
thinner air found at altitudes above 8,000 feet (2,400 
meters).
When turning on the power system in cold weather, 
turn off all electrical accessories such as the lights, 
climate control system, and  rear defogger in order to 
reduce the 12-volt battery drain.
If you live in a region where winter is extremely cold, 
an engine block heater  will improve starting and 
warming of the engine. Cons ult a dealer for details.
If the exhaust system sounds abnormal or you can 
smell exhaust gas inside the  vehicle, have your vehicle 
checked by a dealer. There may be a problem with 
the engine or exhaust system.
Brake Pedal
17 ACCORD FHEV-31T3W6200.book  416 ページ  2016年4月11日 月曜日 午後2時40分 
Page 418 of 584

Continued417
uuWhen Driving uTurning on the Power
Driving
3. Press the  POWER button without 
depressing the accelerator pedal.
4. Check the READY  indicator.
u Keep depressing the brake pedal until 
the READY  indicator comes on.
u The READY  indicator comes on when 
the power system is on and you can start 
driving.
u If the outside temperature is extremely 
low, you cannot drive until conditions are 
improved. In this case, the READY  
indicator does not come on, as well as a 
warning message appears on the multi-
information display.
2 Multi-Information Display Warning 
and Information Messages  P. 88
1Turning on the Power
The immobilizer system pr otects your vehicle from 
theft.
If an improperly coded de vice is used, the power 
system does not activate. 2 Immobilizer System  P. 134
Bring the smart entry remote close to the  POWER 
button if the battery in the smart entry remote is 
weak.
2 If the Smart Entry Remote Battery is Weak  
P. 546
The power system may not activate if the smart entry 
remote is subjected to strong radio waves.
If the smart entry remote battery is low, touch the 
POWER  button with the remote.
2 If the Smart Entry Remote Battery is Weak  
P. 546
The engine may not run when  the vehicle is ready for 
driving.
You can start driving with the  READY indicator on.
If you press the  POWER button while depressing the 
brake pedal with the  READY indicator on, the power 
mode is set to VEHICLE OFF (LOCK) and you cannot 
start driving. 2 READY Indicator  P. 75
17 ACCORD FHEV-31T3W6200.book  417 ページ  2016年4月11日 月曜日 午後2時40分 
Page 421 of 584

uuWhen Driving uTurning on the Power
420
Driving
You can turn the power system off when  the vehicle is completely stopped.
1. Shift to 
(P.
2. Press the  POWER button.
1. While depressing the brake pedal, press the POWER  button.
2. Keeping your right foot on the brake pedal, check that the  READY indicator is on, 
then release the parking brake. Check th at the parking brake indicator has gone 
off.
2 Parking Brake P. 463
3.Put the shift lever in (D. Select (R when reversing.
4. Gradually release the brake pedal and gently depress the accelerator pedal to pull 
away.
■Hill start assist system
Hill start assist keeps the brake engaged br iefly to help prevent the vehicle from 
rolling on inclines as you move your fo ot from the brake pedal to the accelerator.
Move the shift lever to 
(D or   when facing uphill, or (R when facing downhill, 
then release the brake pedal.
■Stopping the Power System
■Starting to Drive1 Starting to Drive
The power system is off when the shift lever is moved 
out of 
(P before the  POWER button is pressed. 
Follow the step 1 wh en starting to drive.
When the power system is turned on using the   button 
on the smart entry remoteWhen the power system is turned on using the   button on the smart entry remote
When the power system is turned on in any case
B
1Hill start assist system
Hill start assist may not  prevent the vehicle from 
rolling downhill on a very steep or slippe ry slope, and 
does not operate on small inclines.
Hill start assist is not a replacement for the parking 
brake.
As a hybrid vehicle, the  sounds and vibrations from 
the engine may be absent even though the vehicle is 
ready for driving. It also  makes you fail to recognize 
that you can start.
Make sure to check if the  READY indicator is on 
before you start to drive.
17 ACCORD FHEV-31T3W6200.book  420 ページ  2016年4月11日 月曜日 午後2時40分 
Page 456 of 584

455
uuWhen Driving uVehicle Stability Assist (VSA ®), aka Electronic Stability Control (ESC), System
Driving
This button is on the driver side control panel. 
To partially turn the VSA features on and off, 
press and hold it until you hear a beep.
The traction control stop s fully functioning, 
allowing the wheels to spin more freely at low 
speed. The VSA ® OFF  indicator will also come 
on.
To turn it on again, press the   (VSA ® OFF) 
button until you hear a beep.
VSA ® is turned on every time you turn the 
power system on, even if you press the   
button the last time you drove the vehicle.
■VSA ® OFF Button1 Vehicle Stability Assist (VSA ®), aka Electronic Stability Control 
(ESC), System
With the   button pressed, your vehicle will have 
normal braking and corn ering ability, but VSA® 
traction and stability  enhancement becomes less 
effective.
In certain unusual  conditions when your vehicle gets 
stuck in shallow mud or fr esh snow, it may be easier 
to free it with the   button pressed.
When the   button is pressed, the traction control 
function becomes less effective. This allows for the 
wheels to spin more freely  at low speed. You should 
only attempt to free your  vehicle with the   button 
pressed if you are not able to free it without.
Immediately after  freeing your vehicle, be sure to 
press the   button again. We do not recommend 
driving your vehicle wi th the   button pressed 
(indicator on).
You may hear a motor sound coming from the 
engine compartment while system checks are being 
performed immediately after turning the power 
system on or while driving. This is normal.
VSA ® OFF  Indicator
17 ACCORD FHEV-31T3W6200.book  455 ページ  2016年4月11日 月曜日 午後2時40分