lock HONDA ACCORD HYBRID 2019 Owner's Manual

uu Child Safety u Safety of Infants and Small Children
68
Safe Driving 5. Route the tether strap over the top of the
head restraint and secure the tether strap
hook to the anchor.
5. Route the tether strap over the side of the
head restraint and secure the tether strap
hook to the anchor.
6. Tighten the tether strap as instructed by the
child seat manufacturer.
7. Make sure the child seat is firmly secured by
rocking it forward and back and side to
side; little movement should be felt.
8. Make sure any unused se at belt that a child
can reach is buckled, the lockable retractor
is activated, and the be lt is fully retracted
and locked. 1 Installing a LATCH-Compatible Child Seat
Installing a LATCH-compatible child seat in the
rear center seat
Each outer rear seat is equi pped with a pair of lower
anchors which are used to secure a LATCH-
compatible child seat. The rear center seat, however,
is not equipped with anchors of any kind. The inner
and outer anchors are spaced apart at a standard
distance of 11 inches (280 mm). The distance
between the two inner anc hors is 15.4 inches (390
mm).
LATCH-compatible restraint systems that are fitted
with rigid-type attachments cannot be installed in the
rear center seat. However, a system fitted with
flexible-type attachments can be installed in the
center seat, provided that the manufacturer’s
instructions for that system permit the use of the
inner anchors with the stated spacing.
Before seating a child, make sure that the system is
properly attached to both the lower anchors and
tether anchors.3
WARNING Do not use the lower inner anchors of the
outer rear seats to secure a LATCH-
compatible child seat to the rear center
seat, unless the manufacturer’s instructions
for that system permit the use of inner
anchors with the stated spacing.Anchor Tether Strap
HookStraight top tether type in seat
position with fixed headrest
Straight top tether type in seat position
with fixed headrest
Anchor Tether Strap
HookOther top tether type in seat
position with fixed headrest
Other top tether type in seat position
with fixed headrest
All models

Continued
69uu Child Safety u Safety of Infants and Small Children
Safe Driving
A child seat can be installed with a lap/should er belt in any rear seat or, if absolutely
necessary, the front passenger seat.
1. Place the child seat on the vehicle seat.
2. Route the seat belt through the child seat
according to the seat manufacturer’s
instructions, and insert the latch plate into
the buckle.
u Insert the latch plate fully until it clicks.
3. Slowly pull the shoulder part of the belt all
the way out until it stops. This activates the
lockable retractor.
4. Let the seat belt retract a few inches and
check that the retractor has switched
modes by pulling on the webbing. It should
not pull out again until it is reset by
removing the latch pl ate from the buckle.
u If you are able to pull the shoulder belt
out, the lockable retractor is not
activated. Slowly pull the seat belt all the
way out, and repeat steps 3 – 4.■ Installing a Child Seat with a Lap/Shoulder Seat Belt 1 Installing a Child Seat with a Lap/Shoulder Seat Belt
A child seat that is not properly secured will not
adequately protect a child in a crash and may cause
injury to the child or other vehicle occupants.

uu Child Safety u Safety of Infants and Small Children
70
Safe Driving 5. Grab the shoulder part of the seat belt near
the buckle, and pull up to remove any slack
from the lap part of the belt.
u When doing this, place your weight on
the child seat and push it into the vehicle
seat.
6. Make sure the child seat is firmly secured by
rocking it forward and back and side to
side; less than one inch of movement
should occur near the seat belt.
7. Make sure any unused se at belt that a child
can reach is buckled, the lockable retractor
is activated, and the be lt is fully retracted
and locked. 1 Installing a Child Seat with a Lap/Shoulder Seat Belt
To deactivate a lockable retractor, release the buckle
and allow the seat belt to wind up all the way.

78
Instrument Panel Indicators
M (sequential mode *
/
7-speed manual shift
mode *
) Indicator *
/
Gear Selection
Indicator *
 P. 84Parking Brake and
Brake System
Indicator (Red)
Parking Brake and
Brake System
Indicator (Amber)U.S.
Canada
U.S.
Canada
Automatic Brake
Hold System Indicator
Automatic Brake Hold
IndicatorU.S.
Canada
*1 : When you set the power mode to ON, these indicators come on to indicate that system checks are being perf ormed. They go off a few seconds later or after the engine
has started. If an indicator does not come on or turn off, th ere may be a malfunction in the co rresponding system. To resolve t he issue, follow the instructions in the
owner's manual.  P. 79*1
Malfunction Indicator
Lamp
Charging System
Indicator Anti-lock Brake System
( ABS ) IndicatorSeat Belt Reminder
Indicator
Low Fuel Indicator
Vehicle Stability Assist
® (VSA
® ) System Indicator
Vehicle Stability Assist
® (VSA
® ) OFF IndicatorSupplemental Restraint
System Indicator
Auto High-Beam
Indicator
Low Tire Pressure/TPMS
IndicatorElectric Power Steering
(EPS) System Indicator
Turn Signal and Hazard
Warning Indicators
Lights On IndicatorHigh Beam Indicator
Fog Light Indicator *ECON Mode Indicator System Message Indicator
SPORT Mode Indicator *
Adaptive Cruise Control
( ACC ) with Low Speed
Follow (LSF) Indicator
(Amber) *
/Adaptive Cruise
Control ( ACC ) Indicator
(Amber) *
Lane Keeping Assist
System ( LKAS ) Indicator
(Amber)
Safety Support Indicator
(Amber)
Safety Support Indicator
(Green/Gray) P. 80
 P. 82
 P. 82
 P. 83
 P. 84*1
*1
*1 *1
 P. 93*1
*1
Gear Position Indicator *
 P. 84
Transmission System
Indicator *
 P. 85 , 87
Shift Up Indicator *
 P. 88
Shift Down Indicator *
 P. 88  P. 89
 P. 89
 P. 90
 P. 90
 P. 90
 P. 91*1
*1
*1
*1
 P. 92*1
 P. 92
 P. 94  P. 99
*1
 P. 94
 P. 94  P. 97
 P. 94
Immobilizer System
Indicator
 P. 95 Security System Alarm
Indicator
 P. 96
 P. 96
 P. 98
 P. 100
 P. 101
 P. 104 *1
Adaptive Cruise Control
( ACC ) with Low Speed
Follow (LSF) Indicator
(Green) *
/Adaptive Cruise
Control ( ACC ) Indicator
(Green) *
 P. 100 *1
Lane Keeping Assist
System ( LKAS ) Indicator
(Green)
 P. 100 *1
* Not available on all models

90 uu Indicators u
Instrument Panel Indicator Name On/Blinking Explanation Message
Anti-lock Brake
System ( ABS )
Indicator • Comes on if there is a problem with
the ABS. • Stays on constantly - Have your vehicle
checked by a dealer. With this indicator
on, your vehicle still has normal braking
ability but no anti-lock function. 2 Anti-lock Brake System (ABS) P. 581
Supplemental
Restraint
System
Indicator • Comes on if a problem with any of
the following is detected:
- Supplemental restraint system
- Knee airbag system
- Side airbag system
- Side curtain airbag system
- Seat belt tensioner • Stays on constantly - Have your vehicle
checked by a dealer.
Auto High-
Beam Indicator • Comes on when all the operating
conditions of the auto high-beam
are met. 2 Auto High-Beam P. 197
—

102 uu Indicators u
Instrument Panel Indicator Name On/Blinking Explanation Message
Safety Support
Indicator
(Amber) ●
Comes on when RDM and/or
CMBS TM
shuts itself off. ●
Indicator may come on temporarily when
passing through an en closed space, such
as tunnel. ●
The area around the radar sensor is
blocked by dirt, mud, etc. Stop your
vehicle in a safe place and wipe the debris
off with a soft cloth. ●
Have your vehicle checked by a dealer if
the indicator does not go off even after
you have cleaned the radar sensor. 2 Collision Mitigation Braking
System TM
(CMBS TM
) P. 510 ●
Stays on - The temperature inside the
camera is too high.
Use the climate control system to cool
down the camera.
The system activates when the
temperature inside the camera cools
down. 2 Front Sensor Camera P. 568
* Not available on all models

103 uu Indicators u
Continued
Instrument Panel
Indicator Name On/Blinking Explanation Message
Safety Support
Indicator
(Amber) ●
Comes on when RDM and/or
CMBS TM
shuts itself off. ●
Stays on - The area around the camera is
blocked by dirt, mud, etc. Stop your
vehicle in a safe place and wipe the debris
off with a soft cloth. ●
Have your vehicle checked by a dealer if
the indicator and message are still
displayed even after you have cleaned the
area around the camera. 2 Front Sensor Camera P. 568●
Comes on when mud, snow, or ice
has accumulated in the vicinity of
the blind spot information system
sensor. ●
Comes on while driving - Something
may be interfering wi th the blind spot
information system sensor. Check the
vicinity of the blind spot information
system sensor and remove any obstacles. 2 Blind spot information System *

P. 502●
Indicator may come on temporarily
when the Maximum Load Limit is
exceeded. ●
Make sure the total load is within the
Maximum Load Limit. 2 Maximum Load Limit P. 457
—Models with the blind spot
information system
* Not available on all models

112 uu Indicators u Driver Information Interface Wa rning and Information Messages
Instrument Panel Message Condition Explanation●
Appears after you set the power mode to
ACCESSORY or ON. ●
Appears after you unlock and open the driver’s
door.
2 Starting the Engine P. 465
●
Appears when the steering wheel is locked. ●
Move the steering wheel left and right while pressing the
ENGINE START/STOP button.Automatic transmission/
Continuously variable
transmission models
Manual transmission
models Canadian models
Continuously variable transmission models
for Canadian models
Manual transmission models

133uu Indicators u Driver Information Interface Wa rning and Information Messages
Continued
Instrument Panel
Message Condition Explanation●
Appears if anything covers the radar sensor cover
and prevents the sensor fro m detecting a vehicle in
front. ●
May appear when driving in bad weather (rain,
snow, fog, etc.). ●
When the radar sensor gets dirty, stop your vehicle in a
safe place, and wipe off dirt using a soft cloth. ●
Have your vehicle checked by a dealer if the message
does not disappear even after you clean the sensor
cover. 2 Radar Sensor P. 570●
Appears if the temperature inside the front sensor
camera is too high and some driver assist systems
and auto high-beam cannot be activated. ●
Use the climate control sy stem to cool down the
camera. ●
Disappears - The camera has been cooled down and
the systems are activated normally. 2 Front Sensor Camera P. 568
2 Auto High-Beam P. 197●
Appears if the area around the front sensor camera is
blocked by dirt, mud, etc. and be prevented from
detecting a vehicle in front. ●
May appear when driving in bad weather (rain,
snow, fog, etc.). ●
When the front window gets dirty, stop your vehicle in
a safe place, and wipe it off with a soft cloth. ●
Have your vehicle checked by a dealer if the message
does not disappear even a fter you cleaned the area
around the camera. 2 Front Sensor Camera P. 568
2 Auto High-Beam P. 197

136 uu Indicators u Driver Information Interface Wa rning and Information Messages
Instrument Panel Message Condition Explanation●
Appears when you unlock an d open the driver’s door
while the engine is running by remote engine start. 2 Remote Engine Start with Vehicle Feedback *
P. 469Models with remote engine starter
* Not available on all models