high beam HONDA ACCORD HYBRID 2019 Owners Manual

13
Quick Reference Guide
Turn Signals (P 193)
Lights (P 193)Turn Signal Control Lever
Right
Left
Light Control Switches
Low Beam High Beam
Flashing Wipers and Washers (P 200)
*1:Models with automatic intermittent
wipers
*2:Models without automatic intermittent
wipers Wiper/Washer Control Lever
Adjustment Ring ( -
: Low Sensitivity *1
( -
: Lower speed, fewer sweeps *2
( +
: High Sensitivity *1
( +
: Higher speed, more sweeps *2
MIST
OFF
AUTO *1
: Wiper speed varies automatically
INT *2
: Low speed with intermittent
LO : Low speed wipe
HI : High speed wipe Pull toward
you to spray
washer fluid. AUTO should always be turned OFF before
the following situations in order to prevent
severe damage to the wiper system:
● Cleaning the windshield
● Driving through a car wash
● No rain
Steering Wheel (P 207)
● To adjust, push the adjustment lever
down, adjust to the de sired position, then
lock the lever back in place. Models with automatic intermittent wipers
To lock
To adjust

78
Instrument Panel Indicators
M (sequential mode *
/
7-speed manual shift
mode *
) Indicator *
/
Gear Selection
Indicator *
 P. 84Parking Brake and
Brake System
Indicator (Red)
Parking Brake and
Brake System
Indicator (Amber)U.S.
Canada
U.S.
Canada
Automatic Brake
Hold System Indicator
Automatic Brake Hold
IndicatorU.S.
Canada
*1 : When you set the power mode to ON, these indicators come on to indicate that system checks are being perf ormed. They go off a few seconds later or after the engine
has started. If an indicator does not come on or turn off, th ere may be a malfunction in the co rresponding system. To resolve t he issue, follow the instructions in the
owner's manual.  P. 79*1
Malfunction Indicator
Lamp
Charging System
Indicator Anti-lock Brake System
( ABS ) IndicatorSeat Belt Reminder
Indicator
Low Fuel Indicator
Vehicle Stability Assist
® (VSA
® ) System Indicator
Vehicle Stability Assist
® (VSA
® ) OFF IndicatorSupplemental Restraint
System Indicator
Auto High-Beam
Indicator
Low Tire Pressure/TPMS
IndicatorElectric Power Steering
(EPS) System Indicator
Turn Signal and Hazard
Warning Indicators
Lights On IndicatorHigh Beam Indicator
Fog Light Indicator *ECON Mode Indicator System Message Indicator
SPORT Mode Indicator *
Adaptive Cruise Control
( ACC ) with Low Speed
Follow (LSF) Indicator
(Amber) *
/Adaptive Cruise
Control ( ACC ) Indicator
(Amber) *
Lane Keeping Assist
System ( LKAS ) Indicator
(Amber)
Safety Support Indicator
(Amber)
Safety Support Indicator
(Green/Gray) P. 80
 P. 82
 P. 82
 P. 83
 P. 84*1
*1
*1 *1
 P. 93*1
*1
Gear Position Indicator *
 P. 84
Transmission System
Indicator *
 P. 85 , 87
Shift Up Indicator *
 P. 88
Shift Down Indicator *
 P. 88  P. 89
 P. 89
 P. 90
 P. 90
 P. 90
 P. 91*1
*1
*1
*1
 P. 92*1
 P. 92
 P. 94  P. 99
*1
 P. 94
 P. 94  P. 97
 P. 94
Immobilizer System
Indicator
 P. 95 Security System Alarm
Indicator
 P. 96
 P. 96
 P. 98
 P. 100
 P. 101
 P. 104 *1
Adaptive Cruise Control
( ACC ) with Low Speed
Follow (LSF) Indicator
(Green) *
/Adaptive Cruise
Control ( ACC ) Indicator
(Green) *
 P. 100 *1
Lane Keeping Assist
System ( LKAS ) Indicator
(Green)
 P. 100 *1
* Not available on all models

90 uu Indicators u
Instrument Panel Indicator Name On/Blinking Explanation Message
Anti-lock Brake
System ( ABS )
Indicator • Comes on if there is a problem with
the ABS. • Stays on constantly - Have your vehicle
checked by a dealer. With this indicator
on, your vehicle still has normal braking
ability but no anti-lock function. 2 Anti-lock Brake System (ABS) P. 581
Supplemental
Restraint
System
Indicator • Comes on if a problem with any of
the following is detected:
- Supplemental restraint system
- Knee airbag system
- Side airbag system
- Side curtain airbag system
- Seat belt tensioner • Stays on constantly - Have your vehicle
checked by a dealer.
Auto High-
Beam Indicator • Comes on when all the operating
conditions of the auto high-beam
are met. 2 Auto High-Beam P. 197
—

94 uu Indicators u
Instrument Panel Indicator Name On/Blinking Explanation Message
Turn Signal and
Hazard
Warning
Indicators • Blinks when you operate the turn
signal lever.
• Blink along with al l turn signals if
you press the hazard warning
button. • Does not blink or blinks rapidly - A
turn signal light bulb has blown. Change
the bulb immediately. 2 Replacing Light Bulbs P. 633, 634
—
High Beam
Indicator • Comes on when the high beam
headlights are on. — —
Lights On
Indicator • Comes on whenever the light
switch is on, or in AUTO when the
exterior lights are on. • If you set the power mode to VEHICLE OFF
while the lights are on, a chime sounds
when the driver’s door is opened. —
Fog Light
Indicator *
• Comes on when the fog lights are
on. — —
* Not available on all models

123uu Indicators u Driver Information Interface Wa rning and Information Messages
Continued
Instrument Panel
Message Condition Explanation
• Appears if there is a prob lem with the auto high-
beam. • Manually operate the headlight switch.
• If you are driving with the high-beam headlights when
this happens, the headlight s are changed to low beams.●
Appears when ACC with LSF *
/ACC *
has been
automatically canceled. ●
You can resume the set speed after the condition that
caused ACC with LSF *
/ACC *
to cancel improves. Press
the RES / + button. 2 Adaptive Cruise Control (ACC) with Low Speed
Follow (LSF) *
P. 519
2 Adaptive Cruise Control (ACC) *
P. 535●
Flashes when the system senses a likely collision with
a vehicle in front of you. ●
Take the appropriate means to prevent a collision (apply
the brakes, change lanes, etc.) 2 Collision Mitigation Braking System TM
(CMBS TM
)
P. 510
2 Adaptive Cruise Control (ACC) with Low Speed
Follow (LSF) *
P. 519
2 Adaptive Cruise Control (ACC) *
P. 535
* Not available on all models

133uu Indicators u Driver Information Interface Wa rning and Information Messages
Continued
Instrument Panel
Message Condition Explanation●
Appears if anything covers the radar sensor cover
and prevents the sensor fro m detecting a vehicle in
front. ●
May appear when driving in bad weather (rain,
snow, fog, etc.). ●
When the radar sensor gets dirty, stop your vehicle in a
safe place, and wipe off dirt using a soft cloth. ●
Have your vehicle checked by a dealer if the message
does not disappear even after you clean the sensor
cover. 2 Radar Sensor P. 570●
Appears if the temperature inside the front sensor
camera is too high and some driver assist systems
and auto high-beam cannot be activated. ●
Use the climate control sy stem to cool down the
camera. ●
Disappears - The camera has been cooled down and
the systems are activated normally. 2 Front Sensor Camera P. 568
2 Auto High-Beam P. 197●
Appears if the area around the front sensor camera is
blocked by dirt, mud, etc. and be prevented from
detecting a vehicle in front. ●
May appear when driving in bad weather (rain,
snow, fog, etc.). ●
When the front window gets dirty, stop your vehicle in
a safe place, and wipe it off with a soft cloth. ●
Have your vehicle checked by a dealer if the message
does not disappear even a fter you cleaned the area
around the camera. 2 Front Sensor Camera P. 568
2 Auto High-Beam P. 197

163Controls This chapter explains how to operate th e various controls necessary for driving.
Clock .................................................. 164
Locking and Unlocking the Doors
Key Types and Functions .................. 166
Low Remote Signal Strength ............ 168
Locking/Unlocking the Doors from the
Outside .......................................... 169
Locking/Unlocking the Doors from the
Inside ............................................. 176
Childproof Door Locks ..................... 178
Auto Door Locking/Unlocking .......... 179
Opening and Closing the Trunk ....... 180
Security System
Immobilizer System .......................... 183
Security System Alarm ...................... 184
Opening and Closing the Windows ..... 186 Opening and Closing the Moonroof *
..... 189
Operating the Switches Around the
Steering Wheel
ENGINE START/STOP Button............. 190
Turn Signals ..................................... 193
Light Switches.................................. 193
Fog Lights *
...................................... 195
Daytime Running Lights ................... 196
Auto High-Beam .............................. 197
Wipers and Washers ........................ 200
Rear Defogger/Heat ed Door Mirror *

Button ........................................... 202 Heated Windshield Button ............... 202
Brightness Control ........................... 203
Driving Position Memory System *
.... 205
Adjusting the Steering Wheel .......... 207
Adjusting the Mirrors
Interior Rearview Mirror ................... 208
Power Door Mirrors ......................... 209
Adjusting the Seats .......................... 210
Interior Lights/Interior Convenience
Items ................................................ 221
Climate Control System
Using Automatic Climate Control .... 239
Automatic Climate Control Sensors ... 242 Canadian models
* Not available on all models

193uu Operating the Switches Around the Steering Wheel u Turn Signals
Continued
Controls
Turn Signals The turn signals can be used when the power
mode is in ON.
■ One-touch turn signal
When you lightly push up or down and release
the turn signal lever, th e exterior turn signals
and turn signal indicator blink three times.
This feature can be used when signaling for a
lane change.
Light Switches Rotating the light switch turns the lights on
and off, regardless of the power mode
setting.
■ High beams
Push the lever forward until you hear a click.
■ Low beams
When in high beams, pull the lever back to
return to low beams.
■ Flashing the high beams
Pull the lever back, and release it.Right Turn
Left Turn
■ Manual Operation 1 Light Switches
If you leave the power mode in VEHICLE OFF while
the lights are on, a chime sounds when the driver’s
door is opened.
When the lights are on, the lights on indicator in the
instrument pane l will be on.
2 Lights On Indicator P. 94
Do not leave the lights on when the engine is off
because it will cause the battery to discharge.
If you sense that the le vel of the headlights is
abnormal, have the vehicl e inspected by a dealer.High Beams
Flashing the high beams
Low Beams
Turns on parking, side marker,
tail, and rear license plate lights
Turns on headlights, parking, side
marker, tail, and rear license plate
lights

195uu Operating the Switches Around the Steering Wheel u Fog Lights *
Controls
The headlights automatically come on when the wipers are used several times within
a certain number of intervals with the headlight switch in AUTO .
The headlights automatically go off a few mi nutes later if the wipers are stopped.
The headlights, all other exterior lights, a nd the instrument panel lights turn off 15
seconds after you set the power mode to VEHICLE OFF, take the remote with you,
and close the driver’s door.
If you set the power mode to VEHICLE OFF with the head light switch on, but do not
open the door, the lights turn off after 10 minutes (three minutes, if the switch is in
the AUTO position).
The lights turn on again when you unlock or open the driver’s door. If you unlock
the door, but do not open it within 15 seconds, the lights go off. If you open the
driver’s door, you will hear a lights on reminder chime.
Fog Lights *
When the low beam headlights are on, turn
the fog light switch on to use the fog lights.■ Headlight Integration with Wipers
■ Automatic Lighting Off Feature 1 Automatic Operation (aut omatic lighting control)
Adjust the auto light sensitivity as follows:
Setting The exterior lights come on
when the ambient light is at
MAX
HIGH
MID
LOW
MIN Bright
Dark
1 Headlight Integration with Wipers
This feature activates while the headlights are off in
AUTO .
The instrument panel br ightness does not change
when the headlights come on.
At dark ambient light leve ls, the automatic lighting
control feature turns on the headlights, regardless of
the number of wiper sweeps.
1 Automatic Lighting Off Feature
You can change the headlight auto off timer setting.
2 Customized Features P. 370, 381
Fog Light Switch
* Not available on all models

197uu Operating the Switches Around the Steering Wheel u Auto High-Beam
Continued
Controls
Auto High-Beam Using a camera mounted to the inside of the windshield, this system detects light
sources ahead of the vehicle. Depend ing on the light source, the system
automatically switches the headlights to hi gh beam for optimal visibility at night. 1 Auto High-Beam
The auto high-beam determines when to change the
headlight beams by responding to the brightness of
the lights ahead of your vehicle. In the following
cases, the system may not respond to the lights
properly:
• The brightness of the lights from the preceding or
oncoming vehicle is intense or poor.
• Visibility is poor due to the weather (rain, snow,
fog, windshield frost, etc.).
• Other light sources, such as streetlights and electric
billboards are illumina ting the road ahead.
• The brightness level of th e road ahead constantly
changes.
• The road is bumpy or with many curves.
• A vehicle cuts in front of you, or a vehicle in front
of you is not in the preceding or oncoming
direction.
• Your vehicle is tilted with heavy load in the rear.
If you find the timing of be am changes inconvenient
for driving, change the headlight beams manually.■ The headlight switch is in
AUTO .
■ The lever is in the low beam
position.
■ The low beams are on and the
system recognizes that you are
driving at night.
■ The vehicle speed is above
25 mph (40 km/h).The system operates when:
When the camera detects lig hts coming from a preceding or oncoming vehicle, the
headlights remain in low beam.
When the camera detects no lights coming from a preceding or oncoming vehicle,
the headlights change to high beam.
The view angle or distance that the camera can detect lights ahead differs
depending on conditions, such as the brightness of the lights and the weather.How it works