d16y7 HONDA CIVIC 1998 6.G Workshop Manual

HONDA CIVIC 1998 6.G Workshop Manual CIVIC 1998 6.G HONDA HONDA https://www.carmanualsonline.info/img/13/6068/w960_6068-0.png HONDA CIVIC 1998 6.G Workshop Manual

Page 587 of 2189

HONDA CIVIC 1998 6.G Workshop Manual 12.
D16Y7 engine:
ENGINESTIFFENER
10 X 1.25 mmIt4 Nm (4.5 kqfm,33 lbfltl
Install the bolts in the cylinder head and attach a
chain hoist to the bolts, then lift the engine slightly
to unload the en

Page 591 of 2189

HONDA CIVIC 1998 6.G Workshop Manual Torque Value
A - 15 N.m (1.5 kgf.m, 11 lbf.ft)
B - 27 N.m (2.8 kgf.m. 20 lbift)
C - 31 N.m {3.2 kgnm, 23 lbift)
\
O BALL BEARING (*T)
ANGULAR
BALL BEARING {*2I
O 5TH SYNCHRO HUB
O 5TH SYNCHRO SLEEVE

Page 595 of 2189

HONDA CIVIC 1998 6.G Workshop Manual Mainshaft Assembly
I
lndex
Note the following during reassembly:
. The 3rd/4th and sth svnchro hubs are installed with a press
. Install the angular ball bearing with the thin-edge outer race facing t

Page 613 of 2189

HONDA CIVIC 1998 6.G Workshop Manual 7. lf the clearance is more than the standard, select a
new thrust shim from the following table
NOTE: It the clearance measured in step 6 is within
the standard. go to step 10.
Standard: 0 - 0.10 mm

Page 615 of 2189

HONDA CIVIC 1998 6.G Workshop Manual Cou ntershaft
1. Remove the needle bearing using the special tool as
shown. then remove the oil guide plate
3/g " -16 SLIDE HAMMER
{Commercially available)
PULLER, 25-40 mm07736-AO1000A
\
2. Install t

Page 616 of 2189

HONDA CIVIC 1998 6.G Workshop Manual Mainshaft Thrust Shim
Adjustment
Remove the thrust shim and oil
the transmission housing.
1.gu ide plate from
THRUST SHIM
OIL GUIDEPLATE
TBANSMISSIONHOUSING
Install the 3rd/4th synchro hub, spacer col

Page 786 of 2189

HONDA CIVIC 1998 6.G Workshop Manual Mai nshaft/Cou ntershaft
Linear Solenoid AssemblySpeed Sensors
Replacement
1. Remove the mounting bolts and the linear solenoid
assemory.
Clean the mounting surfaceand flu id passages.
6x1.0mm12 N.m 1

Page 800 of 2189

HONDA CIVIC 1998 6.G Workshop Manual Transmission
Removal
@Maks sure lifts, iacks and safety stands are placedproperly, and hoist bracket ate aftached to the cor_rec{ position on the engine lsee section 1).Apply parking brake and block r

Page 802 of 2189

HONDA CIVIC 1998 6.G Workshop Manual Transmission
Removal(contd)
10. Remove the cotter pins and castle nuts, th€n separatethe balljoints from the lower arms (see section 1gl.
DAMPER PINCH BOLT
NUT
FORI(FORK BOLT
11. Remove the right

Page 812 of 2189

HONDA CIVIC 1998 6.G Workshop Manual Transmission Housing
Removal
MAINSHAFT
TRANSMISSION HOUSINGMOUNTING BOLTS18 Bolts
TRANSMISSIONHANGERTRANSMISSION HOUSING
MAINSHAFTSUB.ASSEMBLY
SENSOR WASHERlD16Y7 engine)
MAINSHAFTSPEED SENSOR
TRANSMI