main relay HONDA CIVIC 2002 7.G User Guide

PGM-FISystem
DTC Troubleshooting (cont'dl
14. Measure voltage between ECM connector terminal
E7 and body ground.
ECM CONNECTOR E 13lPI
MRLYIBEO/YEL)
Wire side of female terminals
ls there battery voltage?
YES Go to step 15.
NO-Update the ECM if it does not have the latest
software, or substitute a known-good EClvl, then
recheck (see page 11-6). lf the symptom/indication
goes away with a known-good ECM, replace the
original ECM.I
Disconnect ECI\4 connector A (31P).
Turn the ignition switch ON (ll).
Measure voltage between body ground and ECIM
connector terminals 43 and 42 individually.
ECM CONNECTOR A {3.IP)
IGP2 IGP1(YEI./BLX) (YEL/BLKI
Wire side of female lerminals
ls there battery voltage?
YES-Go to step 18.
NO Update the ECM if it does not have the latest
software, or substitute a known-good ECM, then
recheck (see page 11-6). lf the symptom/indication
goes away with a known-good ECM, replace the
original ECM/PCl\4.1
15.
to.
17.
11-82
18.
19.
Remove the glove box (see page 20-63).
Remove the PGM-FI main relay '1 {A).
Measure voltage between body ground and ECM
connector terminals A3 and A2 individually.
ECM CONNECTOR A {31PI
IGP2 IGP1(YEL/BLK) (YEL/BLK)
Wire side of female terminals
I s there battery v oltage?
YES Repair shortto power in the wire between
the ECI\4 (A2.A3) and the PGM-Fl main relay 1.1
NO Replacethe PGM Fl main relay 1.!
20.

3.
4.
5.
6.
DTC Pl361: Camshaft Position (CMP) Sensor
B (TDC Sensor) Intermittent Interruption
DTC Pl362: Camshaft Position (CMP) Sensor
B (TDC Sensor) No Signal
1. Reset the ECM (see page 11-4).
2. Start the engine.
ls DTC P1361 and/or P1362 indicated?
YES Go to step 3.
NO- Intermittent failure. system is OK at this time.
Check for poor connections or loose terminals at
the CMP sensor B (TDC sensor) and at the ECM.I
Turn the ignition switch OFF.
Disconnectthe CMP sensor B (TDC sensor) 3P
connector.
Turn the ignition switch ON (ll).
Measure voltage between CMP sensor B (TDC
sensor) 3P connector terminal No. 3 and body
grouno.
CMP SENSOR B {TDC SENSOR) 3P CONNECTOR
{YEL/BLK}
Wire side ol temale terminals
ls there battety voltage?
YES Go to step 7.
NO-Repair open in the wire between the PGM-Fl
main relay 1 and the CMP sensor I (TDC sensor).I
IGP
123
7. l\4easure voltage between CMP sensor B {TDC
sensor) 3P connector terminal No. 1 and body
ground.
CMP S€NSOR 8 ITDC SENSOR) 3P CONNECTOR
Wlre s de ollemaleterminals
ls there about 5 V?
YES-Go to step 8.
NO-Go to step 10.
8. Measure voltage between Cl\ilP sensor B (TDC
sensor) 3P connector terminals No. 2 and No, 3.
CMP SENSON B llOC SENSOfi) 3P CONNECTOF
Wire s de olfema etefminals
ls there battery voltage?
YES-Go to step 9.
NO Repair open in the wire between the CMP
sensor B (TDC sensor) and G101.1
9. Substitute a known-good CMP sensor B (TDC
sensor) and recheck.
ls DTC P1361 and/or P1362 indicated?
YES Update the ECM if it does not have the latest
software, or substitute a known-good ECM, then
recheck (see page 11-6). lf the symptom/indication
goes away with a known-good ECM, replace the
original ECM.I
NO Replace the original CMPsensorB(TDC
sensor).1
(cont'd)
11-95

PGM-FI System
MIL Circuit Troubleshooting (cont'dl
11.
Try to start the engine.
Does the engine start?
YES-Go to step 11.
NO-Go to step 14.
Turn the ignition switch OFF.
Connect ECM connector terminal E31 to bodyground with a jumper wire.
10.
12.
ECM CONNECTOR E 13lPI
MIL(GRN/ORN}
Wire side of female terminals
Turn the ignition switch ON (ll).
ls the M lL on?
YES Update the ECM if it does not have the latest
software, or substitute a known-good ECM, then
recheck (see page 1 1-6). lf the symptom/indication
goes away with a known-good ECIM, replace the
original ECM.I
NO-Check for an open in the wire between the
ECM (E31) and the gauge assembly. Also check for
a blown MIL bulb. lf the wires and the bulb are OK,
replace the gauge assembly.l
Turn the ignltion switch OFF,
Inspect the No. 6 ECU (ECIM) (15A) fuse in the
under-hood fuse/relay box.
ls the f use OK?
YES-Go to step 22.
NO-Go to step 16.
't 4.
15.
ll2l345617l 18I
415161,/ 1182(2t2'23 24z7l/ 12931
JUMPERWIRE
11-98
to.Remove the blown No. 6 ECU {ECfU) (154) fuse
from the under-hood fuse/relay box.
Remove the glove box (see page 20-63) and the
PGM'FI main relay 1.
Check for continuity between body ground and
PGM-Fl main relay 1 4P connector terminals No. 2
and No. 4 individuallv.
PGM-FI MAIN RELAY 14P CONNECTOR
Wrre srde ol lemale termrnals
ls there continuity?
YES-Repair short in the wire between the No.6
ECU (ECl\4) (15A) fuse and the PGM-Fl main relay 1.
Also replace the No.6 ECU (ECM) (15A) fuse.l
NO-Go to step 19.
17.
18.
fVBv) (wHr/
IA BLK)(

19. Disconnect each of the components or the
connectors below, one at a time, and check for
continuity between PGM-FI main relay 1 4P
connector terminal No. 1 and body ground.
. PGfvl-Fl main relay 2. ECM connector A (31P)
. Each injector 2P connector. ldle air control (lAC)valve 3P connector. Camshaft Position (CMP) sensor B (Top dead
center (TDC) sensor) 3P connector. Crankshaft position (CKP) sensor 3P connector
PGM-FI MAIN RELAY 14P CONNECTOR
ls thete continuity?
YES Go to step 20.
NO- Replace the component that made continuity
to body ground go away when disconnected. lf the
item is the ECM, update the ECM if it does not have
the latest software. or substitute a known-good
ECM, then recheck (see page 11-6). lf the symptom/
indication goes away with a known'good ECM,
replace the original ECM.
Also replace the No. 6 ECU (ECM) (15 A) fuse,
Disconnect the connectors of all these components.
. PGM-Fl main relay 2. ECM connector A (31P)
. lnjectors. ldle air control (lAC)valve
. Camshaft Position {CMP) sensor B (Top dead
center (TDC) sensor). Crankshaft position (CKP) sensor
20.
Wire side of female terminals
22.
21. Check for continuity between PGM-FI main relay 1
4P connector termlnal No. 1 and body ground.
PGM-FI MAIN RELAY 14P CONNECTOR
ls there continuity?
YES Repair short in the wire between the PGM-Fl
main relay 1 and each item. Also replace the No. 6
ECU {ECM) (15A) fuse.l
NO-Replace the PGM-Fl main relay 1. Also replace
the No 6 ECU {ECIM) (15A) f use. I
Inspectthe No. 17 FUEL PUI\4P (15A)fuse in the
under-dash f use/relay box.
ls the tuse OK?
YES Go to step 34.
NO Go to step 23.
Remove the blown No, 17 FU EL PUMP (15A) fuse
from the under-dash fuse/relay box.
Disconnect ECfvl connector E (31P).
(conr'd)
23.
24.
Wire side of female terminals
11-99

PGM-FI System
25.
MIL Circuit Troubleshooting (cont'dl
Check for continuity between ECM connector
terminal E9 and body ground.
ECM CONNECTOR E (31P)
Wire side o{ {emale terminals
ls therc continuity?
YES-Go to step 26.
NO Replace the No. lTFUELPUMP(15A)fuse,
and update the ECM if it does not have the latest
software. or substitute a known-good ECM, then
recheck (see page 1 1-6). lf the symptom/indication
goes away with a known-good ECM. replace the
original ECM.I
26. Remove the PGM-Fl main relay 2 (A).
11-100
27. Check for continuity between ECIVI connector
terminal Eg and body ground.
ECM CONNECTOR E 131P)
Wire side oI Jemale terminals
ls there continuity?
YES Repair short in the wire between the No. 17
FU EL PUMP (15A)fuse and the ECM (E9), or
between the No. 17 FUEL PU MP (15 A) fuse and the
PGM-FI main relay 2. Also replace the No. 17 FUEL
PUMP (15A)fuse.l
NO Go to step 28.
Remove the rear seat cushion (see page 20-80).
Remove the access panel from the floor.
Disconnect the fuel pump 5P connector.
\
28.
29.
30.

31. Check for continuity between fuel pump 5P
connector terminal No. 5 and body ground.
FUEL PUMP 5P CONNECTOR
Wire side of temale terminals
ls therc continuity?
YES Repair short in the wire between the fuel
pump and the PGM-Fl main relay 2. Also replace
thE NO. 17 FUEL PUMP (15A) fUSE.T
NO-Go to step 32.
32. Reinstallthe PGM-Fl main relay 2 (A).
33. Check for continuity between fuel pump5P
connector terminal No. 5 and body ground.
FUEL PUMP 5P CONNECTOR
=
Wire side ol lemal€ rerminals
ls there continuity?
YES Replace the PGM-Fl main relay 2. Also
replace the No. 17 FUEL PUMP (15A) fuse.l
NO Check the iuel pump, and replace il if
necessary. Also replace the No. 17 FUEL PUMP(15A) fuse.!
34. Disconnect ECM connector E (31P).
35. Turn the ignition swirch ON {111.
36. Measure voltage between ECM connectorterminal
E9 and body ground.
ECfl CON|{CCIOR E (3rPt
Wire side ol female lerminals
ls there battery voltage?
YES Go to step 37.
NO Repair open in the wire between the No. 17
FUEL PUMP (15A)fuse and the ECM (E9).1
(cont'd)
11-101

PGM-FI System
MIL Circuit Troubleshooting (cont'dl
37. lvleasure voltage between ECM/PCM connector
terminal E7 and body ground.
ECM CONNECTOR E {31PI
Wire side of female terminals
ls there battery voltage?
YES Go to step 42.
NO Go to step 38.
Turn the ignition switch OFF.
Remove the PGM-FI main relay 1
38.
39.{A}
-A
MRLY
11-102
40. lvleasure voltage between PGN4-Fl main relay 1 4P
connector terminal No. 4 and bodv qround.
PGM-FI MAIN RELAY 1ilP CONNECTOR
41.
ls there battery voltage?
YES-Go to step 41.
NO Repair open in the wire between the No. 6
ECU (ECM) (15A) fuse and the PGfM-Fl main relay 1.
I
Check for continuity between PGM-FI main relay 1
4P connector terminal No. 3 and ECM connector
terminal E7.
PGM.FI MAIN RELAY 14P CONNECTOR
\
ECM CONNECTOR E 131PI
ls there continuity?
YES-Testthe PGM-Fl main relay 1 (see page 22-
51 ). lf the relay is OK, update the ECM if it does not
have the latest software, or substitute a known-
good ECM, then recheck {see page 1 1'6). lf the
symptom/indication goes away with a known-good
ECM, replace the original ECM.I
NO*Repair open in the wire between the PGM-FI
main relay 1 and the ECM (E7).1
Wire side ot lemale terminals
MRLY (RED/YEL)
MRLY (RED/YEL)
Wire side of female terminals

42.
43.
44.
45.
46.
Reconnect ECI\4 connector E {31P).
Turn the ignition switch ON (ll).
Measure voltage between body ground and ECM
connector terminals 42 and 43 individually.
Wire side of female terminals
ls there battery voltage?
YES Go to step 51.
NO Go to step 45.
Turn the ignition switch OFF.
Remove the PGM'Fl main relay 1{A)
,A
47. Turn the ignition switch ON (ll).
ECM CONNECTOR A {31PI
49.
50.
48. Measure voltage between PGM-FI main relay 1 4P
connector terminal No. 2 and body ground.
PGM.FI MAIN RELAY 14P CONNECTOR
ls there battery voltage?
YES Go to step 49.
NO Repair open in the wire between the No.6
ECU {ECM) (15A}fuse and the PGM-Fl main
relay 1 . !
Turn the ignition switch OFF.
Check for continuity between PGM-Fl main relay 1
4P connector terminal No. 1 and ECM connector
terminals 42 and 43 individually.
PGM.FI MAIN RELAY IilP CONNECTOR
ls there continuity?
YES Replace the PGM-Fl main relay 1.1
NO Repair open in the wire between the PGM-FI
main relay '1 and the ECM (A2, A3).1
{cont'd}
Wire side of temale terminals
IGPl (YEL/BLK)
Wire side of female terminals
11-103

DTC Pl519: IAC Valve Circuit Malf unction
1. Resetthe ECM (see page 11-4).
2. Turn the ignition switch ON (ll)
ls DTC P 1519 indicated?
YES Go to step 3.
NO-lntermittent failure, system is OK at this time.
Check for poor connections or loose terminals at
the IAC valve and at the ECM.I
3. Turn the ignition switch OFF.
4. Disconnect the IAC valve 3P connector.
5. Turn the ignition switch ON (ll).
6. Measure voltage betlveen IAC valve 3P connector
terminal No. 2 and body ground.
IAC VALVE 3P CONNECTOR
IGP {YEL/BLK)
Wire side of female terminals
ls there battery voltage?
YES Go to step 7.
NO-Repair open in the wire between the IAC valve
and the PGM-Fl main relay 1.1
Turn the ignition switch OFF.
123
7.
8, Check for continuity between body ground and IAC
valve 3P connector terminal No. 1.
IAC VALVE 3P CONNECTOR
123
PG1 {BLK}
a.
Wire side of lemale terminals
Is there continuity?
YES-Go to step 9.
NO Repair open in the wire between the IAC valve
and G'101.1
Disconnect ECM connector A (31P)
Check for continuity between body ground and
ECM connector terminal A12.
ECM CONNECTOR A 131P)
r l2l3l4 5617s
r01l12 .// 1156 ./118192C21
da25126l27ln2930
IACV {BLK/RED}
1,)
Wire side oJ Jemale terminals
ls there continuity?
YES-Repair short in the wire between the IAC
valve and the ECM (A12).1
NO Go to step 1 1.
9.
10.
LCOnI Ol
11-131

ECM ldle Learn Procedure
The idle learn procedure must be done so the ECM can
learn the engine idle characteristics.
Do the idle learn procedure whenever you do any of
these actions:. Disconnect the battery.
Replace the ECM or disconnect its connector.
Reset the ECM.
NOTE: Erasing DTCS with the Honda PGM Tester
does not require you to do the idle learn procedure.
Remove the No.6 ECU {ECM) ( 15A) fuse from the
under-hood fuse/relay box.
Remove the No.19 baftery (80A) fuse from the under-
hood fuse/relay box.
Remove PGM-FI main relay 1.
Remove any of the wires from the under-hood fuse/
retay Dox.
Disconnect any of the connectors from the under
hood fuse/relay box.
Disconnect the connector between the engine
compartment wire harness and ECM wire harness.
Disconnect the G2 terminal from the transmission
ho u srng.
Disconnectthe G'l terminal from the body.
Disconnectthe G101 terminal from the cylinder head
cover.
Procedure:
To complete the idle learn procedure, do this:
1. Make sure all electrical items (Ay'C, audio, rear
defogger, l:ghts, etc.,) are off.
2. Start the engine, and hold it at 3,000 rpm with no
load {in neutral) until the radiator fan comes on, or
until the engine coolanttemperature reaches 194"F(90'c).
3. Let the engine idle for about 5 minutes with the
throttle fully closed.
NOTE: lf the radiator fan comes on, do not include its
running time in the 5 minutes.
11-139