seat HONDA CIVIC 2003 7.G Repair Manual

6. Remove the seat cushion cover (A) withtheseat
cushion pad from the seat cushion frame.
Pull back the edge of the seat cushion cover all the
way around. and release the clips {A), then remove
the seat cushion cover (B).
1.
r {, ]
:F+r
r* ?
8. Installthe cover in the reverse order of removal,
and note these items;
. To prevent wrinkles when installlng a seat
cushion cover, make sure the material is
stretched evenly over the pad before securing
the clips and hooks.. Make sure the side airbag harness and OPDS
harness (passenger's seat) are routed properly.
. Replace any clips you removed with new ones
(A). Installthem with commercially available
upholstery ring pliers (B).
20-79

Seats
Rear Seat Removal/lnstallation
NOTE: Take care not to scratch the body or tear the seat covers.
'1. Remove the rear seat as shown. To remove the seat-back, remove the front portion of the cargo floor mar lseepage 20-52).
2. Install the seat in the reverse order of removal, and note these items:
'Beforeinstallingthecenteranchorboltsontheseat-backwiththecentershoulderbelt,makesurethereareno
twists or kinks in the belt.. Make sure the seat-backs lock securelv.
Fastener Locations
A>:Bolt,2 B>rBolt, 1 C>:Bott, 1D >: Clip, 2
lltl
agrf(1
Vt-r_r+*.
\'7
CUSHION
6x1.0mm9.8Nm{1.0 kgf.m,7.2lbf.ft)
/-<.{\.-- F.i\-- K\-|J].Pt-HAP
CENTER PIVOT BOLT8 x 1.25 mm22 N.m{2.2 kgf.m, 16lbf.ftl
RIGHT SEAT-BACK
CENTER BELT
PIVOT BUSHING
CENTER ANCHOR BOLT7/16-20 UNF32Nm(3.3 kgf m.24 lbt ftl
SEAT BELT BUCKLE
8 x 1.25 mm22 N.m 12.2 kgt m, 16lbf.ft)
SEAT.BACKCENTER HINGE
BUSHING
LEFT SEAT.BACK
PIVOTBUSHING
HOOK
20-80
SEAT

IRear Seat-back Latch Replacement
1.Remove the seat-back (see page 20-80).
Remove the seat-back cover (see page 20-82).
Remove the seat-back pad {A) from the seat-back
frame (B). On right seat-back with center shoulder
belt, pass the center belt (C) through the hole in the
seat-back pad.
Remove the bolts, then remove the seat-back latch
(A) from the seat-back frame (B), and release the
pivot pin {C) of the latch lever (D) from the seat'
back f rame.
Fastener Locations
lnstallthe latch in the reverse order of removal, and
make sure the seat-back locks and unlocks properly.
\
Rear Seat-back Striker Replacement
NOTE: Take care not to scratch the interior trim.
1. Remove the rear side trim panel (see page 20-5'l).
2. Remove the bolts, then remove the seat-back
striker (A).
Fastener Locations
) : Bolt, 2
F
,-;1
8 x 1.25 mm22 N m 12.2 kgl rn,16 tbf.ft)
3. lnstallthe striker in the reverse order of removal,
and move the striker (A) up or down until it is
centered in the seat-back latch {B).
20-81

Seats
Rear Seat-back Cover Replacement
NOTE:. Take care not to tear the seams or damage the seat
covers.. Put on gloves to protect your hands.
'1. Remove the seat-back (see page 20-80).
Remove the headrest.
Pull up the latch cover (A) to telease the clips. then
remove it.
Fastener Locations
) : Clip, 4
1W
4.Pull up the outside edge of the latch lever cover (A)
to release the clips, and release the cover from thepivot pins (B) ofthe latch lever {C) while pulljng the
latch lever.
Fastener Locations
D : Clip, 2
i
*rJ
20-82
5. On right seat-backi Using a Torx T30 bit, remove
the bolts, then remove the belt holder trim (A), and
remove the trim from the center belt (B).
Fastener
) : Bolt,
A*-\./-
Locations6x1.0mm9.8Nm(1.0 kgf.m,7.2 lbf.ft)
Release the hook (A), and unzip the seat-back cover(B). The right seat-back is shown. the left seat-back
is similar.
\

7. Pull back the edge of the seat-back cover (A), and
release the clips {B).
Pull back the edge of the seat-back cover, and pull
out the seat-back frame {A) from the seat-back pad
{B), then pull out the headrest guide (C) while
pinching the end of the guides, and remove them.
9. Remove the seat-back cover (A)from the seat-back
pad (B). On right seat-back with center shoulder
belt, pass the center belt (C) through the hole in the
seat-bacl( cover.
lnstallthe cover in the reverse order of removal,
and note these items:
. To prevent wrinkles when installing a seat-back
cover, make sure the material is stretched evenly
over the pad before securing the hooks and clips
. On right seat-back: When installing the seat-back
frame to the pad, slip the center belt through the
hole in the seat-back cover and pad.
. Replace any clips you removed with new ones.
Install them with commercially available
upholstery ring pliers.
10,
20-83

Seats
Rear Seat Cushion Cover Replacement
'1.Remove the rear seat cushion (see page 2O-80).
Release all the clips (A) from under the seat
cushion, and fold back the seat cushion cover (B).
B
Pull back the edge of the seat cushion cover all theway around, and release the clips (A), then remove
the seat cushion cover.
iw F 1., 1L +. ts+'
il1rl-,+ J ,+ l l
20-84
4. Installthe cover in the reverse order of removal,
and note these items;
. To prevent wrinkles, make sure the material is
stretched evenly over the pad before securing
the clips.. Replace any clips {A) you removed with new
ones. Install them with commercially available
upholstery ring pliers (B).
\

Heating and Air Gonditioning
Compressor Clutch Overhaul (cont'd)
5. Reassemble the clutch in the reverse order of
disassembly, and note these items:
. Installthe field coil with the wire side facing
down, and align the boss on the field coil with the
hole in the compressor.. Clean the rotor pulley and compressor sliding
surfaces with contact cleaner or other
non-petroleum solvent..Install new snap rings, note the installation
direction, and make sure they are fully seated in
the groove.
. Make sure that the rotor pulley turns smoothly
after it's reassembled,. Route and clamp the wires properly or they can
be damaged by the rotor pulley.
21-50

Body Electrical
General Troubleshooting Information (cont'd)
Check for loose retainer (A) and rubber seals (B).
The backs of some connectors are packed with
dielectric grease. Add grease if necessary. lf thegrease is contaminated, replace it.
lnsert the connector all the way and make sure it is
securelv locked.
Position wires so that the open end of the cover faces
oown.
22-4
Handling Wires and Harnesses. Secure wires and wire harnesses to lhe frame with
their respective wire ties at the designated locations.. Remove clips carefully; don't damage their locks (A).
Slip pliers (A) under the clip base and through the
hole at an angle, then squeeze the expansion tabs to
release the clip.
After installing harness clips, make sure the harness
doesn't interfere with any moving pans.
Keep wire harnesses away from exhaust pipes and
other hot parts, from sharp edges of brackets and
holes, and from exposed screws and bolts.
Seat grommets in their grooves properly {A). Do not
leave grommets distorted (B).
lt" /wl/
\--------\tfl r'---'..-
It
J
|,f . ./.ll t/
----E; F.'l/
I

Relay and Control Unit Locations
Door and Seat
Driver's Door:
Passenger's Seat:
l\:
].\
POWER WINDOW MASTER SWITCHlHas built-in control unit)
22-12

Connectors and Harnesses
Connector to Harness lndex (cont'd)
Floor Wire Harness (Front sidel
Connec-tor or TerminalI Refuavftres Location connects to Nol6sDriver's seat belt switchDriver's side airbag inflatorDriver's side impact sensorLeft side seat belt buckle tensionerMemory erase signal (MES) connectorParking brake switchPassenger's seat belt switchPassenger's side airbag inflatorPassenger's side impact sensorRight side seat belt buckle tensionerSRS unit connector BSRS unit connector CUnder-dash fuse/relay boxconnector P {see page 22-45)Under-dash fuse/relay boxconnector O (see page 22,45)c402
c403
c453
c508
c509
c512
11l013121995374202111
'r8
22
23
2
14
1
6
3 I Under driver's seat2 i Under driver's seat2 I Left side offloor4 Under driver's seat2 Under dash fuse/relay box1 1 Middle offloor3 Under passenger's seat2 Under passenger's seat2 Right side offloor4 Under passenger's seat18 I Under middle of dash8 Under middle of dash18 Underdash fuse/relay box
8
]
Under dash fuse/relay box
10
I
Under middle of dash
4 Under middle of dash
6 Under middle of dash
4 Under middle of dash
6 Under middle ofdash
8
I
Under middle of dash
10 Under middle of dash
4 ] Unaer middle of aasn
Dashboard wire harness B{see page 22 30)Dashboard wire harness B(see page 22-30)ECM wire harness (see page22-321Dashboard wire harness A(see page 22-26)Dashboard wire harness A\see page 22-26)Dashboard wire harness A{see page 22-26)Engine compartment wireharness (see page 22 18)OPDS unit harness (see page22-421G551IL,nder passenger's seatBody ground via floor wire
22-34