maintenance reset HONDA CIVIC COUPE 2016 10.G Quick Guide

26 || 27
INSTRUMENT PANEL
INSTRUMENT PANEL
Condition Indicators
These indicators may require you to perform an action.
Parking brake
Release the parking brake before driving. You will hear a beep if you drive with it not fully released. Seat belt reminder Make sure seat belts are fastened for you and all passengers. The indicator
blinks and beeps sound continuously if you or your front passenger has not
fastened your seat belts when you begin driving. If the indicator remains on
after seat belts are fastened, see your dealer. Door/trunk open A door or the trunk is not closed. A beep sounds if open while driving. Low fuel
Refuel as soon as possible. If the indicator blinks, there is a problem with the
fuel gauge. Have your vehicle checked by a dealer. Low tire pressure*
Stop in a safe place, check tire pressures, and inate tire(s) if necessary. The indicator also appears if the system has not been calibrated (see page 118).
Washer uid level *
The washer uid is low. Rell the washer uid (see page 137).System message* When a condition or malfunction indicator comes on, a message also appears on the Driver Information Interface. Check the display for more information. Press the display/information button on the steering wheel to clear the message. Maintenance Minder* Scheduled maintenance for your vehicle is due. Immobilizer/security system
Your key or remote transmitter cannot be recognized by the vehicle. If the
indicator blinks, you may not be able to start the engine. Turn the vehicle off, remove the key from the ignition*, press and hold the brake pedal, and restart the vehicle. If it continues to blink, there may be a problem with the
system. Have your vehicle checked by a dealer. Canadian models: To reset the immobilizer system, follow the steps above
after the battery has been disconnected.
U.S.
Canada
*if equipped VSA off VSA engaged (blinking)CRUISE MAIN onCRUISE CONTROL onACC* onCMBS* offLKAS* on
Turn signals/hazards on Fog lights* onHigh beams onExterior lights onECON mode onAutomatic brake hold onAutomatic brake hold activated
U.S.
Canada
On/Off Indicators
These indicators remind you when an item is on or off.
Brake depress Press the brake pedal before applying or releasing the electric parking
brake or automatic brake hold. A blinking indicator means automatic brake hold operation ceased. Immediately press the brake pedal.
CV
T models
MT models

128 || 129
MAINTENANCE
MAINTENANCE
Maintenance Minder™
Reminds you when indicated maintenance service is due.
Models with information display
When maintenance is due, the Maintenance Minder indicator comes on and a message
appears on the display every time you turn the vehicle on. Press the TRIP knob in the instrument panel to change displays (see page 28).
Models with Driver Information Interface
When maintenance is due, the system message indicator comes on and a message
appears on the display every time you turn the vehicle on. Press the display/information button on the steering wheel to change displays (see page 29).
Maintenance Minder message
Maintenance
Minder indicator
Sub items
Main item
Maintenance Minder message
System message

indicator
Sub items
Main item
U.S. models
Maintenance, replacement, or repair of emissions control devices and systems may be done by any automotive repair establishment or individuals using parts that are
certied to EPA standards. According to state and federal regulations, failure to perform maintenance on the
maintenance main items marked with # will not void your emissions warranties.
However, all maintenance services should be performed in accordance with the intervals indicated by the Driver Information Interface.
Maintenance Minder Service Codes
These codes indicate what services are due on your vehicle.
U.S. models
*1: If a Maintenance Minder indicator does not appear more than 12 months after the display is
reset, change the engine oil every year.
#: See information on maintenance and emissions warranty.
CODEMaintenance Main Items
A 
Replace engine oi l*1
B
Replace engine oi l*1
and oil lter
 Inspect front and rear brakes
 Inspect these items:
• Tie rod ends, steering gear box, and boots
•S uspension components
• Driveshaft boots
• Brake hoses and lines (including ABS/VSA)
• All uid levels and condition of uids
• Exhaust system #
•F uel lines and connection s#
*2:If you drive in dusty conditions, replace the air cleaner element every 15,000 miles (24,000 km).*3:If you drive primarily in urban areas that have high concentrations of soot in the air from industryand diesel-powered vehicles, replace the dust and pollen lter every 15,000 miles (24,000 km).*4:Driving in mountainous areas at very low vehicle speeds results in higher transmission
temperatures. This requires transmission uid changes more frequently than recommended by
the Maintenance Minder. If you regularly drive your vehicle under these conditions, have the
transmission uid changed every 25,000 miles (40,000 km).
CODEMaintenance Sub Items
1 
Rotate tires
2
Replace air cleaner element *2
 Replace dust and pollen lter *3
 Inspect drive belt
3 
Replace transmission uid *4
4
Replace spark plug s
 Inspect valve clearance
5 
Replace engine coolant
7Replace brake uid*5
*5:If a Maintenance Minder indicator does not appear more than 36 months after the display for item 7 is reset, change the brake uid every 3 years.
In addition: •  Inspect idle speed every 160,000 miles (256,000 km).
•  Adjust the valves during services A, B, 1, 2, or 3 if they are noisy.

130 || 131
MAINTENANCE
MAINTENANCE
*1: If a Maintenance Minder message does not appear more than 12 months after the display is
reset, change the engine oil every year.
*2: If you drive in dusty conditions, replace the air cleaner element every 24,000 km (15,000 miles). *3:
If you drive primarily in urban areas that have high concentrations of soot in the air from industryand diesel-powered vehicles, replace the dust and pollen lter every 24,000 km (15,000 miles).
*4: Driving in mountainous areas at very low vehicle speeds results in higher transmission
temperatures. This requires transmission uid changes more frequently than recommended by
the Maintenance Minder. If you regularly drive your vehicle under these conditions, have the
transmission uid changed every 40,000 km (25,000 miles).
*5: If a Maintenance Minder Indicator does not appear more than 36 months after the display for
item7 is reset, change the brake uid every 3 years.#:See information on maintenance and emissions warranty.
CODEMaintenance Main Items
A 
Replace engine oi l*1
0
Replace engine oi l*1
and oil lte r
CODEMaintenance Sub Items
1 
Rotate tires
2Replace air cleaner element *2
 Replace dust and pollen lte r*3
 Inspect drive belt
3 
Replace transmission uid *4
4
Replace spark plugs
 Inspect valve clearance
5 
Replace engine coolant
7
Replace brake uid *5
9 
Service front and rear brakes
 Inspect these items:
•T ie rod ends, steering gearbox, and boots
•S uspension components
•D riveshaft boots
•B rake hoses and lines (including ABS/VSA)
•A ll uid levels and condition of uid s
•E xhaust system #
•F uel lines and connections #
Canadian models
In addition: • 
Inspect idle speed every 256,000 km (160,000 miles).
•  Adjust the valves during services A, 0, 1, 2, 3, or 9 if they are noisy.
Under the Hood
1.5 ℓ engine models
Brake fluid (black cap)
Reserve tank
Washer fluid (blue cap) Engine oil dipstick (orange)
Engine oil fill cap
Battery
Reserve tank cap
U.S. odelsWasher fluid (blue cap)

134 || 135
MAINTENANCE
MAINTENANCE
Recommended Engine Oil
•  Honda Genuine Motor Oil
•  Premium-grade 0W-20 detergent oil with an API Certication Seal on the
container
This seal indicates the oil is energy conserving and
that it meets the American Petroleum Institute’s latest requirements. Use Honda Genuine Motor Oil or another commercial engine oil of suitable viscosity for the ambient temperature as shown.
You may also use synthetic motor oil if it is labeled with the API Certication Seal and is of the specied viscosity grade.
Adding Oil
1. Unscrew and remove the engine oil ll cap.
2. Add oil slowly.
3. Reinstall the engine oil ll cap, and tighten it securely.
4. Wait for three minutes and recheck the engine oil dipstick.
Ambient temperature
Engine oil ll cap
1.5 ℓ engine models
Engine oil ll ca p
2.0 ℓ engine models
Do not ll the engine oil above the upper mark. Overlling the engine oil can result in leaks and engine damage.
NOTICE
Resetting the Engine Oil Life
If you change or replace the vehicle’s engine oil yourself, you must reset the engine oil life.
Models with information display
1. Press the TRIP knob in the instrument panel until
the engine oil life appears in the display.
2. Press and hold the knob for 10 seconds or more, until the display begins to blink.
3. Press and hold the knob for 5 seconds or more. The engine oil life display returns to 100%.
Models with Driver Information Interface
Use the steering wheel buttons to make and enter selections (see page 29).
1. Scroll to the Maintenance Minder screen, and select it.
2. Press and hold the ENTER button for about 10 seconds to enter the reset mode.
3. Scroll to the maintenance item you want to reset (or All Due Items), and select it.
Models with Display Audio
Use the touchscreen to make and enter selections.
1. From the HOME screen, select Settings.
2. Select Vehicle.
3. Select Maintenance Info.
4. Select Select Reset Items.
5. Select an item on the list to reset.
Failure to reset the engine oil life after a maintenance service results in the system showing incorrect maintenance intervals, which can lead to serious mechanical problems.
NOTICE

138 || 139
MAINTENANCE
MAINTENANCE
Checking the Battery
Check the battery terminals for corrosion monthly. For jump starting, see page 114.
The battery gives off explosive hydrogen gas during normal operation. A spark or ame can cause the battery to explode with enough force to kill or seriously hurt you. When conducting any battery maintenance, wear protective clothing and a face shield, or have a skilled technician do it. Battery posts, terminals, and related accessories contain lead and lead
compounds. Wash your hands after handling.
WARNING
Changing Wiper Blades
If the wiper blades leave streaks across the windshield, try cleaning them rst with a paper towel or soft cloth and wiper uid. If the wiper blade rubber has deteriorated, you should change the wiper blades.
1. Turn the vehicle off.
2. Hold the wiper switch in the MIST position, then turn the vehicle on. Both wiper arms lift up. Turn the vehicle off.
3. Lift both wiper arms.
4. Press and hold the tab, then slide the blade holder toward the base of the wiper arm.
5. Slide the wiper blade out from its holder by pulling the tabbed end out.
6. Slide the new wiper blade into the holder. The tab on the holder should t in the indent of the wiper blade.
7. Slide the wiper blade holder onto the wiper arm securely.
8. Lower the passenger side wiper arm rst, then the driver side.
Tab
Blade
Tab
Blade
TabBlade
Avoid dropping the wiper arm, as it may damage the windshield.
NOTICE
After replacing or reconnecting the battery, keep in mind:
•  Some systems are temporarily deactivated. Drive a short distance at 12 mph (20
km/h) or more, and the indicator(s) should go off.
•  The immobilizer system needs to be reset (see page 26).*
*Canadian models only
Holder
Holder
Cap