tire size HONDA CIVIC COUPE 2016 10.G Quick Guide

98 || 99
DRIVING
DRIVING
Braking
Slow down or stop your vehicle, and keep it from moving when parked.
Foot Brake
Press the brake pedal to slow down or stop your vehicle from moving.
Brake Assist System
During hard or emergency braking, the system increases braking force. The brake pedal may move slightly or make a noise; this is normal. Continue to hold the brake pedal rmly down.
Anti-lock Brake System (ABS)
During hard or emergency braking, the system rapidly pumps the brakes to prevent wheel lockup and help you maintain steering control. The brake pedal may pulsate slightly during ABS operation; this is normal. Do not pump the brake pedal, and continue to hold it rmly down.
Brake pedalCVT
Brake pedal
The ABS may not function correctly if you use an incorrect tire type and size.
NOTICE
Electric Parking Brake
Keep your vehicle from moving while parked using a simple switch.
To apply: Pull up the switch. The BRAKE indicator
appears in the instrument panel.
To release: Press the brake pedal and make sure
your seat belt is fastened. Press the switch down to release. The parking brake can release automatically:
CVT models: Depress the accelerator pedal while
the transmission is in D or R.Manual transmission models: Depress the
accelerator pedal and release the clutch while the transmission has a gear engaged. All models: Automatic release works only when your seat belt is fastened.
Pull up to apply.
Press down to release.
Manual transmission
Automatic Brake Hold
Maintains brake hold even after the brake pedal is released. Make sure the vehicle is on and your seat belt is fastened when operating this feature.
1. Press the BRAKE HOLD button behind the shift
lever. The BRAKE HOLD indicator appears in the instrument panel.
2. With the shift lever in Drive (D) or Neutral (N), press the brake pedal and come to a complete stop. The HOLD indicator appears, and brake hold is applied. Release the brake pedal.
Press the accelerator pedal (or shift into a gear and release the clutch pedal for manual transmission) to cancel brake hold and start moving.
To turn off brake hold: Press the brake pedal and press the BRAKE HOLD button
again.
Automatic brake hold cancels when: •  Braking is applied for more than 10 minutes.
•  The electric parking brake is engaged.
•  The foot brake is pressed and the shift lever is moved to P or R.
•  The engine stalls (manual transmission).
•  The driver’s seat belt is unfastened.
•  The engine is turned off.
Activating the automatic brake hold system on steep hills or slippery roads may still allow the vehicle to move if you remove your foot from the brake pedal.
If a vehicle unexpectedly moves, it may cause a crash resulting in serious injury or death.
Never use the automatic brake hold system or rely on it to keep a vehicle from moving when stopped on a steep hill or slippery roads.
WARNING
Using the automatic brake hold system to park the vehicle may result in the vehicle unexpectedly moving.
If a vehicle moves unexpectedly, it may cause a crash, resulting in serious injury or death.
Never leave the vehicle when braking is temporarily kept by automatic brake
hold and always park the vehicle by putting the transmission in Park (P) and applying the parking brake.
WARNING

118 || 119
HANDLING THE UNEXPECTED
HANDLING THE UNEXPECTED
Tire Pressure Monitoring System (TPMS)
Monitors the tire pressure while you are driving. If your vehicle’s tire pressure becomes
signicantly low, the low tire pressure indicator comes on and a message appears on
the display. Available on U.S. models only.
What to Do
Stop your vehicle in a safe place. Check the tire pressure and adjust the pressure to the specied
level on the label on the driver’s doorjamb.
TPMS Calibration
Any time you inate, change, or rotate one or more of the tires, you need to recalibrate the system.
The calibration process requires approximately 30 minutes of cumulative driving at
speeds between 30–65 mph (48–105 km/h). The vehicle must be stopped to begin
calibration, and the process nishes automatically.
Models with TPMS button
Press and hold the TPMS button until the low tire pressure indicator blinks twice, indicating the calibration process has begun.
Models with color audio system and Driver Information Interface
Use the steering wheel buttons to make and enter selections in the Driver Information Interface (see page 29).
1. Scroll to the Vehicle Settings screen, and select it.
2. Select TPMS Calibration.
3. Select Calibrate.
Models with Display Audio
Touch items on the screen to make and enter selections.
1. From the HOME screen, select Settings.
2. Select Vehicle.
3. Select TPMS Calibration.
4. Select Calibrate.
TPMS button
Low tire pressure/ TPMS indicator

Tire Pressure Monitoring System (TPMS) - Required Federal Explanation
Each tire, including the spare (if provided), should be checked monthly when cold and inated to the ination pressure recommended by the vehicle manufacturer on the vehicle placard or tire ination pressure label. (If your vehicle has tires of a different size than the size indicated on the vehicle placard or tire ination pressure label, you should determine the proper tire ination pressure for those tires.) As an added safety feature, your vehicle has been equipped with a tire pressure monitoring system (TPMS) that illuminates a low tire pressure telltale when one or more of your tires is signicantly underinated.
Accordingly, when the low tire pressure telltale illuminates, you should stop and check your tires as soon as possible, and inate them to the proper pressure. Driving on a signicantly underinated tire causes the tire to overheat and can lead to tire failure. Underination also reduces fuel efciency and tire
tread life, and may affect the vehicle’s handling and stopping ability. Please note that the TPMS is not a substitute for proper tire maintenance,
and it is the driver’s responsibility to maintain correct tire pressure, even if underination has not reached the level to trigger illumination of the TPMS low tire pressure telltale.
Your vehicle has also been equipped with a TPMS malfunction indicator to
indicate when the system is not operating properly. The TPMS malfunction indicator is combined with the low tire pressure telltale. When the system detects a malfunction, the telltale will ash for approximately one minute and then remain continuously illuminated. This sequence will continue upon subsequent vehicle start-ups as long as the malfunction exists. When the malfunction indicator is illuminated, the system may not be able to detect or signal low tire pressure as intended. TPMS malfunctions may occur for a variety of reasons, including the installation of replacement or alternate tires or wheels on the vehicle that
prevent the TPMS from functioning properly. Always check the TPMS malfunction telltale after replacing one or more tires or wheels on your vehicle to ensure that the replacement or alternate
tires and wheels allow the TPMS to continue to function properly.
Driving on an extremely underinated tire can cause it to overheat. An overheated tire can fail. Always inate your tires to the specied pressure.
NOTICE

120 || 121
HANDLING THE UNEXPECTED
HANDLING THE UNEXPECTED
Changing a Flat Tire
If a tire goes at while driving, grasp the steering wheel rmly, and brake gradually to reduce speed. Then, stop in a safe place. Replace the at tire with the compact spare
tire. Go to a dealer as soon as possible to have the full-size tire repaired or replaced.
Getting Ready to Change the Tire
Park the vehicle on a rm, level, non-slippery surface. Apply the parking brake, shift
to Park (P), and turn the vehicle off. Turn on the hazard warning lights.
1. Open the trunk oor lid.
2. Take the tool case out of the trunk. Take the jack
and wheel nut wrench out of the tool case.
3. Unscrew the wing bolt, then remove the spacer cone. Remove the spare tire.
4. Place the compact spare tire (wheel side up) under the vehicle body, near the tire that needs to be replaced.
5. If necessary, put the at tip of the jack handle bar into the edge of the wheel cover. Carefully
pry the edge and remove the cover.
6. Loosen each wheel nut about one turn using the wheel nut wrench.
Spare Tire Tool Case
Jack handle ba
r
Wheel nu t
Wheel cover
Setting Up the Jack
1. Place the jack under the jacking point closest to
the tire to be changed.
2. Turn the end bracket clockwise (as shown in the image) until the top of the jack contacts the jacking point. Make sure that the jacking point tab is resting in the jack notch.
3. Raise the vehicle, using the jack handle bar and the jack handle, until the tire is off the ground.
Jacking Points
Jack handle bar Wheel nut
Wrench as jack handle
The vehicle can easily roll off the jack, seriously injuring anyone underneath.
Follow the directions for changing a tire exactly, and never get under the vehicle when it is supported only by the jack.
WARNING
The following instructions must be followed to use the jack safely: •  Do not use the jack with people or luggage in the vehicle.
•  Use the jack provided in your vehicle. Other jacks may not support the weight
(“load”) or t the jacking point.
•  Do not use while the engine is running.
•  Use only where the ground is rm and level.
•  Use only at the jacking points.
•  Do not get in the vehicle while using the jack.
•  Do not put anything on top of or underneath the jack.

122 || 123
HANDLING THE UNEXPECTED
HANDLING THE UNEXPECTED
Replacing the Flat Tire
1. Remove the wheel nuts and at tire.
2. Mount the compact spare tire. Replace the
wheel nuts, and lightly tighten them.
3. Lower the vehicle and remove the jack. Tighten the wheel nuts in the order indicated in the image. Go around, tightening the nuts, two to
three times in this order. Do not overtighten the wheel nuts.
Models with wheel covers: Make sure the wire
support ring is hooked into the clips around the edge
of the wheel cover. Align the valve mark on the wheel cover to the tire
valve on the wheel, then install the wheel cover. If you drive with the spare tire installed, the low tire pressure/TPMS indicator appears. The indicator stays on until a regular tire is installed.
spilC
spilC
Valve mark
Storing the Flat Tire
1. Remove the center cap, if necessary.
2. Open the trunk. Place the at tire face down in
the spare tire well.
3. Remove the spacer cone from the wing bolt, ip it over, and insert it back on the bolt. Secure the at tire with the wing bolt.
4. Models with wheel covers: Make sure the wire
support ring is hooked into the clips around the
edge of the wheel cover.
5. Securely put the jack and wheel nut wrench back in the tool case. Store the case in the trunk.
Loose items can y around the interior in a crash and can seriously injure the occupants. Store the wheel, jack, and tools securely before driving.
WARNING
Spacer cone Wing bolt
For compact
spare tireFor full -
size tire
Tire valv e
Wire support rin g

140 || 141
MAINTENANCE
MAINTENANCE
Tire Information
To safely operate your vehicle, your tires must be of the proper type and size, in good condition with adequate tread, and properly inated.
Inflation Guidelines
•  Properly inated tires provide the best combination of handling, tread life, and
comfort. Refer to the driver’s doorjamb label or the specications (see page 147) for the specied pressure.
•  Underinated tires wear unevenly, adversely affect handling and fuel economy,
and are more likely to fail from overheating.
•  Overinated tires make your vehicle ride harshly, are more prone to road hazards,
and wear unevenly.
•  Every day before you drive, look at each of the tires. If one looks lower than the
others, check the pressure with a tire gauge.
•  Measure the air pressure when tires are cold. This means the vehicle has been
parked for at least 3 hours, or driven less than 1 mile (1.6 km). If necessary, add or release air until the specied pressure is reached, and then calibrate the system
(see page 118). If checked when hot, tire pressure can be as much as 4–6 psi (30–40 kPa, 0.3–0.5 kgf/cm 2
) higher than checked when cold.
•  At least once a month or before long trips, use a gauge to measure the pressure in
all tires, including the spare. Even tires in good condition can lose 1–2 psi (10–20 kPa, 0.1–0.2 kgf/cm 2
) per month.
Inspection Guidelines
Every time you inate the tires, check for the following: •  Any damage to tires, including bumps, bulges, cuts, splits, or cracks in the side or
tread. Remove any foreign objects and inspect for air leaks. Replace tires if you see fabric or cord.
•  Uneven or excessive tread wear. Have a dealer check the wheel alignment.
•  Cracks or other damage around the valve stems.
Wear Indicators
The groove where the wear indicator is located is 1/16 inch (1.6 mm) shallower than elsewhere on the tire. If the tread has worn so low that the indicator is exposed, replace the tire. Worn out tires have poor
traction on wet roads.
Example of a wear indicator mark
Tire and Loading Information Label
The label attached to the driver’s doorjamb provides necessary tire and loading information.
Tire and Wheel Replacement
Replace your tires with radials of the same size, load range, speed rating, and
maximum cold tire pressure rating (as shown on the tire’s sidewall). Using tires of a
different size or construction can cause certain vehicle systems to work incorrectly.
It is best to replace all four tires at the same time. If that isn’t possible, replace the front or rear tires in pairs.
If you change or replace a wheel, make sure that the wheel’s specications match those of the original wheels. Using tires that are excessively worn or improperly inated can cause a crash in which you can be seriously hurt or killed.
Follow all instructions in this owner’s manual regarding tire ination and maintenance
.
WARNING
Original tire sizesNumber of people your vehicle can carryProper cold tire pressureTotal weight your
vehicle can carry (do not exceed)
Installing improper tires on your vehicle can affect handling and stability. This can cause a crash in which you can be seriously hurt or killed.
Always use the size and type of tires recommended in the Owner’s Manual.
WARNING

142 || 143
MAINTENANCE
MAINTENANCE
Tire Service Life
The life of your tires is dependent on many factors, including driving habits, road
conditions, vehicle loading, ination pressure, maintenance history, speed, and environmental conditions (even when the tires are not in use). In addition to regular inspections and ination pressure maintenance, it is recommended that you have annual inspections performed once the tires reach ve years old. All tires, including the spare, should be removed from service after 10 years
from the date of manufacture, regardless of their condition or state of wear.
Winter Tires
If driving on snowy or frozen roads, mount all season tires marked “M+S”, snow tires,
or tire chains; reduce speed; and maintain sufcient distance between vehicles when
driving. For winter tires, select the size and load ranges that are the same as the original tires, and mount them to all four wheels.
Tire Chains
Because your vehicle has limited tire clearance, we strongly recommend using the following chains: For 215/55R16 tires:
Cable-type: Autotrac 0154505 For 215/50R17 tires:
Cable-type: Autotrac 0154005
Install tire chains on the front tires only. Mount chains as tightly as you can, and make sure that they do not touch the brake lines or suspension.
Using the wrong chains, or not properly installing chains, can damage the brake lines and cause a crash in which you can be seriously injured or killed.
Follow all instructions in this guide regarding the selection and use of tire chains.
WARNING
Traction devices that are the wrong size or improperly installed can damage your
vehicle’s brake lines, suspension, body, and wheels. Stop driving if they are hitting any part of the vehicle.
NOTICE
Tire Labeling
The tires that came on your vehicle have a number of markings. Those you
should be aware of are described below. Here is an example of what each marking means: P205/55R16 89H
P: Vehicle type (passenger)205: tire width in millimeters55: aspect ratio (tire section height as a percentage of its width) R: tire construction code (radial)16: rim diameter in inches89: load index (code indicating maximum load tire can carry) H: speed symbol (code indicating maximum speed rating)
Tire Identification Number (TIN)
The tire identication number (TIN) is a group of numbers and letters that look like the
example below. TIN is located on the sidewall of the tire.
Glossary of Tire Terminology
Cold Tire Pressure – The tire air pressure when the vehicle has been parked for at least three hours or driven less than 1 mile (1.6 km). Load Rating – The maximum load that a tire is rated to carry for a given ination pressure. Maximum Ination Pressure – The maximum tire air pressure that the tire can hold.
Maximum Load Rating – The load rating for a tire at the maximum permissible ination pressure for that tire. Recommended Ination Pressure – The cold tire ination pressure
recommended by the manufacturer.
Treadwear Indicators (TWI) – The projections within the principal grooves designed to give a visual indication of the degrees of wear of the tread.
Tire size
Tire identication number (TIN)
Maximum tire load
Maximu m
tire pressure
Tire siz e
DOT B97R FW6X 2209 DOT: This indicates that the tire meets allrequirements of the U.S. Department ofTransportation .
B97R: Manufacturer’s identication markFW6X: Tire type code22 09: Date of Transportation

Year
Week

146 || 147
SPECIFICATIONS
MAINTENANCE
Testing of Readiness Codes
Your vehicle has “readiness codes” as part of the onboard self-diagnostic system. Some
states refer to these codes as a test to see if your vehicle’s emissions components are
working properly. The codes may not be read if you go through the testing just after the battery has gone dead or been disconnected.
To check if they are set, turn the vehicle on without starting the engine. The malfunction
indicator lamp will come on for several seconds. If it goes off, the readiness codes are set. If it blinks ve times, the readiness codes are not set. If you are required to have your vehicle tested before the readiness codes are set, prepare the vehicle for retesting by doing the following:
1. Fill the gas tank to approximately 3/4 full.
2. Park the vehicle and leave the engine off for 6 hours or more.
3. Make sure the ambient temperature is between 40°F and 95°F (4°C and 35°C).4. Start the engine without touching the accelerator pedal, and let it idle for 20 seconds.
5. Keep the vehicle in Park (P) or Neutral for manual transmission. Increase the engine speed to 2,000 rpm, and hold it there for about 3 minutes.
6. Let the engine idle with your foot off the accelerator for 20 seconds.
7. Select a nearby, lightly traveled major highway where you can maintain a speed of 50 to 60 mph (80 to 97 km/h) for at least 20 minutes. Drive on the highway with
the vehicle in Drive (D) or 5th gear. Do not use cruise control. When trafc allows,
drive for 90 seconds without using the accelerator pedal. (Vehicle speed may vary
slightly; this is OK.) If you cannot do this for a continuous 90 seconds because of
trafc conditions, drive for at least 30 seconds, then repeat two more times (for a total of 90 seconds).
8. Drive in city/suburban trafc for at least 10 minutes. When trafc conditions allow, let the vehicle coast for several seconds without using the accelerator pedal or the brake pedal.
9. Park the vehicle and leave the engine off for 30 minutes.
The readiness codes are erased when the battery is disconnected, and set again only after several days of driving under a variety of conditions.
If a testing facility determines that the readiness codes are not set, you may be
requested to return at a later date to complete the test, or see your dealer.SPECIFICATIONS 1.5-L engine models
Vehicle
ModelHonda Civic 2-Doo r
No. of Passengers :
Fron t2
Rear 3
Tota l5
Weights:Gross Vehicle Weight Rating U.S.: 3,902 lbs (1,770 kg )
Canada: 1,770 kg
Gross Axle Weight
Rating (Front )U.S.: 2,105 lbs (955 kg )
Canada: 955 kg
Gross Axle Weight
Rating (Rear)U.S.: 1,808 lbs (820 kg )
Canada: 820 kg
Light Bulbs
*1:Models with halogen headlights*2: Models with LED headlights
Headlights (Low Beam)55W (H11) *1
LE D*2
Headlights (High Beam )60W (HB3)
*1
LE D*2
Fog Lights35W (H8
)
Parking/Da ytime Running Light sLED
Front Side Marker Lights3W
Front Turn Signal Lights 21W (Amber
)*1
LE D*2
Side Turn Signal Lights

(on Door Mirrors) *LE
D
Brake Light s2 1W
Rear Turn Signal Lights21W (Amber)
Rear Side Marker Lights LED
Back-Up Lights16 W
DEL
sthgilliaT
High-M ount Brake LightRear License Plate Light LEDTrunk Light5W
In terior Lights
Map Lights8 W
Ceiling Ligh t8 W
DEL
Engine and Fuel
Engine FuelDisplacemen t91.26 cu-in (1,496 cm 3
)
Spark Plug sN GKILZKAR8H8S
Fuel: TypeUnleaded gasoline, Pump octane number of 87 or highe r
Fuel Tank Capacity 12.39 US gal (46.9 ℓ)
Fluids
Air ConditioningRefrigerant TypeHFO-1234yf (R-1234yf)
Charge Quantity 13.2 – 15.0 oz (375 – 425 g)
Lubricant TypeRL85HM (POE)
Quantity 2.7 – 3.6 oz (77 – 103 g)
Washer Fluid
Tank CapacityU.S.: 2.6 US qt (2.5 ℓ) Canada: 4.8 US qt (4.5 ℓ)
Brake Fluid
Continuously Variable Transmission Fluid
SpeciedHonda Heavy Duty Brake Fluid DOT 3
SpeciedHonda HCF-2 Transmission Flui d
Capacity Change 3.9 US qt (3.7 ℓ)
Engine Oil
Engine Coolan
t
Recommended·Genuine Honda Motor Oil 0W-20 ·API Premium-grade 0W-20 detergent oi l
Capacity Change
3.4 US qt (3.2 ℓ)
Change including
lte r 3.7 US qt (3.5 ℓ)
SpeciedHonda Long Life Anti
freeze/Coolant Type 2
Ratio 50/50 with distilled wate r
Capacity1.34 US gal (5.09 ℓ)

(change including the remaining
0.2 US gal (0.75 ℓ) in the reserve tank )
Tires
RegularSize215/50R17 91HPressure psi (kPa [kgf/cm 2
])32 (220 [2.2] )
Compact Spar e Size
T125/80D16 97M
Pressure psi (kPa [kgf/cm 2
]) 60 (420 [4.2]
)
Wheel SizeRegular17 x 7JCompact Spar e16 x 4T

148 || 149
CUSTOMER INFORMATION
SPECIFICATIONS
2.0-L engine models
Vehicle
Model Honda Civic 2-Door
No. of Passengers :
Fron t2
Rear 3
Tota l5
Weights:Gross Vehicle Weight Rating U.S.: 3,737 lbs (1,695 kg )
Canada: 1,695 kg
Gross Axle Weight
Rating (Front )U.S.: 1,984 lbs (900 kg )
Canada: 900 kg
Gross Axle Weight
Rating (Rear)U.S.: 1,786 lbs (810 kg )
Canada: 810 kg
Light Bulbs
Headlights (Low Beam)55W (H11)Headlights (High Beam )60W (HB3)Parking/Daytime Running Light sLED
Front Side Marker Ligh t
Front Turn Signal Lights21W (Amber )
Brake Lights 21W
Rear Turn Signal Lights21W (Amber)
Rear Side Marker Lights LED
Back-Up Lights16W
DEL
sthgilliaT
High-M ount Brake LightRear License Plate Light LEDTrunk Light5W
In terior Lights
Map Light s8W
Ceiling Ligh t8 W
3W
DEL
Engine and Fuel
Engine FuelDisplacemen t121.76 cu-in (1,996 cm 3
)
Spark Plug s NG
K DILKAR7H11GS DILKAR7G11GS
DENSO DXE22HQR-D11 S
Fuel: TypeUnleaded gasoline, Pump octane number of 87 or highe r
Fuel Tank Capacity 12.39 US gal (46.9 ℓ)
Fluids
Air Conditioning *Refrigerant TypeHFO-1234yf (R-1234yf)
Charge Quantity 13.2 – 15.0 oz (375 – 425 g)
Lubricant TypeRL85HM (POE)
Quantity 2.7 – 3.6 oz (77 – 103 g)
Washer Fluid
Tank CapacityU.S.: 2.6 US qt (2.5 ℓ) Canada: 4.8 US qt (4.5 ℓ)
Brake/Clutch Fluid
Continuously Variable Transmission Fluid Manual Transmission Fluid
SpeciedHonda Heavy Duty Brake Fluid DOT 3
SpeciedHonda HCF-2 Transmission Flui d
Capacity Change 3.7 US qt (3.5 ℓ)
SpeciedHonda Manual Transmission Fluid (MTF )
Capacity Change 2.0 US qt (1.9 ℓ)
Engine Oil
Engine Coolan
t
Recommended·Genuine Honda Motor Oil 0W-20 ·API Premium-grade 0W-20 detergent oi l
Capacity Change
4.2 US qt (4.0 ℓ)
Change including
lte r 4.4 US qt (4.2 ℓ)
SpeciedHonda Long Life Anti
freeze/Coolant Type 2
Ratio 50/50 with distilled wate r
Capacity1.4 US gal (5.30 ℓ)
(change including the remaining
0.2 US gal (0.75 ℓ) in the reserve tank )
*
*
*
Tires
RegularSize215/55R16 93HPressure psi (kPa [kgf/cm 2
])32 (220 [2.2] )
Compact Spar e* Size
T125/80D16 97M
Pressure psi (kPa [kgf/cm 2
]) 60 (420 [4.2]
)
Wheel SizeRegular16 x 7JCompact Spar e16 x 4T
*if equipped
CUSTOMER INFORMATION
*if equipped
Learn about information specic to you as a Honda customer and how to get help.
Frequently Asked Questions/Troubleshooting
Below are some frequently asked questions and troubleshooting items that you may have about the vehicle. Q:
How do I set the vehicle clock?
A: For vehicles without navigation, see page 51. For vehicles with navigation, the
time is automatically set using GPS signals.Q: Why doesn’t the vehicle start when I press the ENGINE START/STOP button?*
A: The brake pedal must be pressed to start the engine.
Q: What is the AUTO* setting on my headlight lever?
A: When in the AUTO position, the vehicle’s exterior lights will automatically turn
on or off depending on the ambient lighting.Q: Why won’t the driver’s door unlock when I grab the door handle, even though 
  the keyless access remote is within range?* A: If you pull the handle too quickly, the system may not have time to conrm the
door is unlocked. Wait to hear a beep to conrm the door is unlocked. If you are
wearing gloves, the system may be slow to respond. Q: After my battery was disconnected or went dead, the audio system is asking for 
  a code. Where do I ind this? A: In most cases, you do not need to enter a code. Turn on the vehicle and the
audio system, and press and hold the power button until the system reactivates. Q: Why can’t I operate Pandora through the audio system?*
A: Audio may be streaming through Bluetooth Audio. Make sure Pandora mode
is selected and the phone cable is properly connected to the USB adapter
cable (if using). Some phones may prompt you to “Allow” a connection. Q: Is my phone compatible with  Bluetooth features?
A: Visit handsfreelink.com (U.S.) or www.handsfreelink.ca (Canada) to
check phone compatibility for Bluetooth Audio, Bluetooth HandsFreeLink,
and SMS text messaging.Q: Every time I press the Talk button, the system gives me voice prompts. Can I turn 
  these off?* A: From the Home screen, select SETTINGS. Select System, then select Voice
Prompt. Select Off.