Tension HONDA CR-V 1998 RD1-RD3 / 1.G Repair Manual

Ftom page24-54
Check for 6 short power in the cable r6el {cont'd):5. Reconnect the battery positive cable, then reconnect thenegative cable.6. Erase the DTC memory (see page 24-28).7. Read the DTC (see page 24-261.
b DTC 1-4 indicarodz
YESNO
Short to power in lhe cablo roel; replace th€ cabl€ ieel{see pago 24-91).
Check tor a short to power in th. SRS main harn$s:1. Disconnect the battery negative cable, then disconnectthe positive cable, and wait for three minutes.2. Disconnect the front passenger's airbag connector {anddisconnect both seat belt tensioner connectors).3. Rernove the special tool (2 O) from the SRS main harness2P connector.4. Disconnect the SRS main harness 18P connector fromthe SRS unit.5. Beconnect the batterv positive cable, then reconnect thenegative cable.6. Connect a voltmeter between the No. 1 {+) terminal olthe SRS main harness 18P connector and body ground.7. Turn the ignition switch ON (ll), and measure voltage.There should be 0.5 V or less.8. Turn the ignition switch OFF.9. Connect a voitmeter between the No. 13 {+i terminal ofthe SRS main harness 18P connector and body ground.10.Turn the ignition switch ON lll), and measure voltage.There should be 0.5 V or less.
Are voltages as specified?
YESNO
Faulty SRS unit; replaco th€ SRS unit lsoo pas6 24-95).
Short to power in th€ SRS main hamoss; roplece the SRSmain haanass.
SRS MAIN HARNESS18P CONNECTOR
24-55
www.emanualpro.com

)
SRS MAIN HARNESS18P CONNECTOR
)
From page 24 56
Check{or a short to ground in the cable reel (cont'd):
5. Reconnect the batterv positive cable, then reconnect thenegative cable.6. Erase lhe DTC memoty lsee page 24-28).7. Read the DTC lsee page 24 26).
ls OTC 1-5 indicated?
YESNO
Short lo ground in the cable reel; replace the cable reel{see oaoe 2,1-91}.
Check for a short to ground in the SRS main harness:'1. Disconnect the battery negative cable, the disconnect thepositive cable, and wait for three minutes.2. Disconnect the tront passenger's airbag 2P connector(6nd disconnect both seat belt tensioner connectors).3. Remove the special tool 12 {))from the SRS main harness2P connector.4- Disconnect the SRS main harness 18P connector fromthe sRs unit.5. Check resistance between the No. l terminal o{theSRSmain harness 18P connector and ground, and betweenthe No. 13 terminal of the SRS main harness 18P connec-tor and ground.There should be I M0 or more.
ls lhe resistance as soecitiod?
NOYES
Faulw SRS unit reDlace the SRS unit lsee paqe 24-951.
Short to ground in the SRS main harness; replace the SRSmain ham€ss,
24-57
www.emanualpro.com

)
From page 24 58
Check fo. an oD6n in the SRS main harness:1. Disconnect the battery negative cable, then disconnectthe positive cable, and wait for three minutes.2. Disconnectthe driver's airbag 2P connector land disconnectboth seat belt tensioner connectors) (see page 24 23).3. Disconnect the SRS main harness 18P connector fromthe SRS unit. Do not disconnect the soecial tool (2 Oifrom the SRS main harness.4. Check resistance between the No. 10 terminal and No. 14terminal of the SRS main harness 18P connector. Thereshould be aoorox. 2.0 - 3.0 g.
ls the .osistanc€ as soecified?
NOYES
Poor contacl ai the SRS main harness 18P connecloricheck lhe connector,.lf the conneclor is OK, substitute a known-good SRSunit, and recheck..lf the problem is still present, replace the SRS mainhatnesli,
Open or increased resistance in the SRS main harness;replace the harness.
UNITsRs
18P CONNECTOR
24-59
www.emanualpro.com

)
SRS MAIN HARNESS18P CONNECTOR
)
)
From page 24 60
Ch6ck tor a short to another wire or decreasod aGsistance inlh€ SRS main harness:1. Disconnect the battery negative cable, then disconnectthe positive cable, and wait for three minutes.2. Disconnect the driver's airbag 2P connector (and disconnectboth seat belt tensioner connectors).3. Disconnect the SRS main harness '18P connector fromthe SRS unit. Do not disconnect the special tool (2 O).4. Check resistance between the No. 10 terminal and No. 14terminal of the SRS main harness 18P connector. Thereshould be aoorox. 2.0 - 3.0 0.
ls the rosistanc6 as specified?
YESNO
Faultv SRS unit; replace lhe SRS unit lsee page 24-95).
Short to anothor wire or decre.sed re3i3t.nce in the SRSmain harness; replac€ the SRS main harn*s.
24-61
www.emanualpro.com

Frcm page24-62
Check lor a short to power in the SRS main harness:
1. Disconnect the battery negative cable, then disconnectthe positive cable, and wait for three minutes.
2. Disconnect the drive/s airbag 2P connector (and disconnect
both seat belttensionerconnectors).3. Disconnect the SRS main harness 18P connector trom
the SRS unit.4. Remove the specialtool (2 0) from the SRS main harness
2P connector,5. Reconnect the batterv positive cable, then reconnect the
negative cable.6. Connect a voltmeter between the No. 10 (+) terminal of
SRS main harness 18P connector and ground.
7. Turn the ignition switch ON (ll). and measure voltage
There should be 0.5 V or less.8. Connect a voltmeter between the No. 141+) terminal of
the SRS main harness 18P connector and ground, and
measure voltage. There should be 0.5 V or less.
Are voltages .3 specifiedT
YESNO
Faulty SRS unit; replace the SRS unit (sce page 24'95).
Short to powor in the SRS main ha.ne3s; replace the SRS
main hdrness.
sRs.I8P CONNECTOR
24-63
www.emanualpro.com

)J
From page 24'64
Check for a short to ground in the SRS main harnessl1. Disconnect the battery negative cable, then disconnectthe posilive cable. and wait for three minutes.2. Disconnect the driver's airbag 2P connector (and discon-nect both seat belt tensioner connectors),3. Disconnect the SBS main harness 18P connector fromthe sRs unit.4. Remove the special tool (2 O) from the SRS main harness2P connector,5. Check resistance between the No. 10 terminal of the SRSmain harness 18P connector and ground, and betweenthe No. 14 terminal of the SRS main harness 18P connector and ground. There should be 1 M0 or more.
ls the resistance as sD€citied?
NOYES
Faultv SRS uniu replace the SRS unit {see paqe 24-951.
Short to ground in the SRS main harn€ss; replac€ ihe SRSmain harness.
sRs18P CONNECTOF
24-65
www.emanualpro.com

Troubleshooting
DTC 3-1 and DTC 3-2
CAUTION: Whenever the ignition switch is ON flll, orhas been turned OFF for less than three minutes, b€careful not to bump th€ SRS unit; the airbags couldaccidenlally deploy and cause damage or iniuries.
DRIVER'SSEAT BELT TENSIONERLEFT SIOE WIREHARNESS2P CONNECTOR2P CONNECTOR
-
\
SRS SIMULALEAD C07TAZ - SZ501rAand SRS INFLATORSTMULAToR It2 0JACKI IoTsaz - TB4ot lA t
24-66
Try to reproduce the SRS indicatoi light:1. Erase the DTC memory (see page 24-29).2. Turn the ignition switch ON 1 ), and check that the SRSindicator light comes on for about six seconds and thengoes off.
Does the SRS indicaior lighr stay on?
YESNO
Intermittent failure, system is OK at this time. SeeTroubleshooting lfiermittent Failu.6s on page 24-28.
Check tor an open in the driver's seat b6lt tensioner:1. Disconnect the negative battery cable, and wait lor threeminutes.2. Disconnect the drave/s seat belt tensioner 2p connectorfrom the left side wire harness 2P connector (see page24-23). Do not disconnect the lront passenger,s seat belttensioner 2P connector.3. Connect the special tool {2 O) to the left side wire harness2P connector,4. Reconnect the negative baftery cable5. Erase the DTC memory {see page 24,28).6. Read the DTC (see page 24-26).
ls OTC 3-1or DTC 3-2 indicatedT
YESNO
Open or increased resistance in the d.iver's seat belt ten-sioner; replace the driver's seat belt {see page 2il-91).
To page 24 67
www.emanualpro.com

)
LEFT SIDE WIREHARNESS2P CONNECTOR
SRS MAINHARNESS2P CONNECTOR
C
00
SRS SIMULATORLEAD C07TAZ - SZ5011Aand SRS INFLATOR
{2 0 JACKI07sAz - T84011A
art)
sRsUNIT
SRS MAIN HARNESS.I8P CONNECTOR
)
From page 24-66
Check for an oFn in thc aide wir6 harne$:1. Disconnect the left side wire harness 2P connector fromthe SRS main harness 2P connector.2. Connect the special tool (2 o) to the SRS main harness2P connector.3. Erase the DTC memory.4. Read the DTC.
ls DTC 3-l or DTC 3-2 indicated?
YESNO
Ooen or incrers€d reeidance in the lelt side wire hame3s;r€Dlaca the hamess.
Check for an open in the SRS main harness:1. Disconnect the negative battery cable, and wait for threeminutes.2. Disconnect the driver's and front passenger's airbags,and front passenger's seat belt tensioner connectors (see
page 24-231.3. Disconnect the SRS main harness 18P connector from
the SRS unit. Do not disconnect the special tool (2 O)from the SRS main harness 2P connector.4. Check resistance between the No. 4 and No. 11 terminalsof the SRS main harness 18P connector. There should be2.0 - 3.0 0.
13lhe resistance as soecified?
NOYES
Faulty SFS unil or poor contad at the SRS main h.m€ss18P connector and th€ SRS unit. check the connectionbetween the SRS main harn$s 18P connector and theSRS unit. lf the connector i3 OK. r€Dlaco ihe SRS unit(s66 pas6 24-951.
ODen or incaoased resistance in the SRS msin harness;reolace the SRS main harn€ss.
terminals
24-67
www.emanualpro.com

Troubleshooting
DTC 3-3
CAUTION; Whenever the ignition switch is ON llll, or
has b€on turned OFF for l6ss than three minutes, be
carelul not to bump the SRS unit; the airbags could
accidontally deploy and cause damage or iniuries.
ORIVER'SSEAT EELT TENSIONER2P CONNECTOR
SRS SIMULATORLEAO C07TAZ-525011Aand SRS INFLATORsrMULAroR It2 0 JACK| tozsAz - ls{orra !
s
Try to r€produce the SRS indicator light:1. Erase the DTC memory (see page 24-28).2. Turn the ignition switch ON (lll, and check that the SRSindicator light comes on for about six seconds and thengoes off.
Does the SRS indicator lighl stay on?
YESNO
Intarmittent failure, system is OK at this time. 506Troubl€shooting Intormittant Failures on paqe 24-28.
Check tor a 3hort to anoth€r wire or decreased resistance inihe driver's seat bolt tan3ioneri1. Disconnect the negative battery cable, and wait for threeminutes,2. Disconnect the driver's seat belt tensioner 2P connectorfrom the left side wire harness 2P connector (see page24-23). Do not disconnect the front passenger's seat belttensioner 2P connector,3. Connect the special tool (2 O) to the left side wire harness2P connector.4. Reconnect the negative battery cable5. Erase the DTC memory (see page 24-28).6. Read the DTC (see page 24.26l'.
ls DTC 3-3 indicated?
NOYES
Short to another wire or decreased.esistance in thedriver's s6at beh tcnsioner; replac€ the diive.'s seat bolt{se€ prge 24-911.
To page 24 69
24-64
LEFT SIDE WIREHARNESS2P CONNECTOB
ra
www.emanualpro.com

From page 24-68
Check lor a short to another wire or decreased reaistance inthe side wire harnoss:1. Disconnect the left side wire harness 2P connector tromthe SRS main harness 2P connector.2. Connect the special tool (2 0) to the SRS main harness2P connector.3. Erase the DTC memory.4. Read the DTC.
ls OTC 3-3 indicated?
YESNO
Short to another wire or decrcased resbtance in the le-hside wire harness; reglace the harneas.
Check lor a 3hort to another wire or dec.eased resistance inthe SRS main ha.ne$:1. Disconnect the negative battery cable, and wait for threeminutes,2. Disconnect the driver's and front passenger's airbags,and front passenger's seat belt tensioner connectors (seepage 24 23l'.3. Disconnect the SRS main harness 18P connector fromthe SRS unit.4. Disconnect the special tool (2 O) from the SRS main harness2P connector.5. Check resistance between the No. 4 and No. 11 terminals ofthe SRS main harness 18P connector. There should be1 M0 or more.
ls the resistanc€ as soocified?
NOYES
Faulty SRS unit; replace the SRS unit lso€ paqe 24-95).
Short to another wire or decr€asod rosistanco in the SBSmain harness; replace the SRS main harness.
\.p
LEFT SIDE WIREHARNESS2P CONNECTOR
SRS MAINHANNESS
C0a
2P CONNECTOR
SRS SIMULATORLEAD C07TAZ - SZ5011Aand SRS INFLAToRSIMULATOR{2 0 JACK}07sAz - TB4011A
IJ
SRS MAIN HARNESS18P CONNECTOR
SRS UNIT
lerminals.
IJ
t,rutEr-
24-69
www.emanualpro.com