Transmission assembly HONDA CR-V 1998 RD1-RD3 / 1.G Workshop Manual

HONDA CR-V 1998 RD1-RD3 / 1.G Workshop Manual CR-V 1998 RD1-RD3 / 1.G HONDA HONDA https://www.carmanualsonline.info/img/13/5778/w960_5778-0.png HONDA CR-V 1998 RD1-RD3 / 1.G Workshop Manual

Page 41 of 1395

HONDA CR-V 1998 RD1-RD3 / 1.G Workshop Manual 
Lubrication Points
For the details of lubrication points and type of lubricants to be applied. refer to the illustrated index and various work pro-
cedures (such as Assembly/Reassembly, Replacement,

Page 89 of 1395

HONDA CR-V 1998 RD1-RD3 / 1.G Workshop Manual 
Disconnest the lilP connector from the control unit.
Csvity WireTest condition
R€conn€ct tho 14P connGctor to the control unit.
Test: Desired resultPossible cause it result is not obtained
BRNAr

Page 102 of 1395

HONDA CR-V 1998 RD1-RD3 / 1.G Workshop Manual 
Engine Removal/lnstallation
Removal (contd)
17. Disconnect the power steering pressure {psp} switchconnector, and remove the wire harness clamo.
Remove the slave cylinder and clutch hose bracket(Mrr

Page 440 of 1395

HONDA CR-V 1998 RD1-RD3 / 1.G Workshop Manual 
Manual Transmission
Diff€rential
lndex ...................... ......... 13-38
Backlash Inspestion ..,....,.,.....................,......, 13-38
Final Driven Gear Replacement .................... 13

Page 443 of 1395

HONDA CR-V 1998 RD1-RD3 / 1.G Workshop Manual 
Transfer Assembly
lnspection
@ Make sure tifts, iacks, and satety stands
are placed properly (see section 1).
L Raise the front of the vehicle, and support it with
safety stands (see section 1).
2. S

Page 444 of 1395

HONDA CR-V 1998 RD1-RD3 / 1.G Workshop Manual 
Removal
!@@ Make sure the lifts, i8cks. and safety stands
are placed properly {see section 1}.
1. Raise the front of the vehicle, and support it with
safety stands (see section 1).
2. Set the parking

Page 445 of 1395

HONDA CR-V 1998 RD1-RD3 / 1.G Workshop Manual 
Transfer Assembly
lnstallation
1. Install a new O-ring on the transfer assembly.
8 x 1.25 mm24 N.m (2.4 kgt m,17 rbt.ftl
10 x 1.25 mm44 N.m (4.5 kgJ.m,
2.
DOWEL PIN
Replace.TRANSFEBASSEMBLY
Clean the

Page 446 of 1395

HONDA CR-V 1998 RD1-RD3 / 1.G Workshop Manual 
Transmission AssemblY
Removal
@FMak. sw. iack" and safety stands are placed propel-
ly, and hoist brackets are attached to collect position
on the engine,
. Apply parking brake and block rear wheels

Page 447 of 1395

HONDA CR-V 1998 RD1-RD3 / 1.G Workshop Manual 
Transmission Assembly
Removal (contdl
6. Remove the cotter pins,
washers, plastic washers.
cable from the levers.
then remove the steel
shift cable, and select
1.
8.
Remove the cable bracket from th

Page 449 of 1395

HONDA CR-V 1998 RD1-RD3 / 1.G Workshop Manual 
Transmission Assembly
Removal (contd)
20. Remove the intermediate shaft.
21.Tie plastic bags over the both ends of the intermedi-
ate shaft. Coat all precision finished surfaces withclean engine oil
Page:   1-10 11-20 21-30 31-40 41-50 ... 80 next >