reset HONDA ELEMENT 2005 1.G Owners Manual

µ
Canadian models onlyThis indicator reminds you that it is
time to take your vehicle in for
scheduled maintenance.
This indicator comes on if any door
is not closed tightly. This indicator comes on if the
tailgate or the hatch is not closed
tightly. This indicator comes on when the
washer f luid level is low. Add washer
f luid when you see this indicator
come on (see page ). Ref er to the maintenance schedules
f or normal and severe driving
conditions on pages
.
For the f irst 8,000 miles (12,800 km)
af ter the maintenance required
indicator is reset, it will come on f or
2 seconds when you turn the ignition
switch to ON (II).
Between 8,000 miles (12,800 km)
and 10,000 miles (16,000 km), this
indicator will come on f or 2 seconds
when you first turn the ignition
switch to ON (II), and then flash for
10 seconds. Hold the button for about 10
seconds until the indicator goes
of f . Press and hold the Select/Reset
button on the instrument panel,
then turn the ignition switch to
ON (II). Turn of f the engine.
Your dealer will reset this indicator
af ter completing the scheduled
maintenance. If this maintenance is
notdonebyyourdealer,resetthe
indicator as f ollows. If you exceed 10,000 miles (16,000
km) without having the scheduled
maintenance perf ormed, this
indicator will remain on as a constant
reminder.
1.
2.
3.
174
165 166
Washer L evel Indicator
Maintenance Required
Indicator
Door-open Indicator Tailgate and Hatch Open
Indicator
Instrument Panel Indicators
Inst rument s and Cont rols
57

This shows the number of miles (U.S.)
or kilometers (Canada) driven since
you last reset it.
There are two trip meters: Trip A
and Trip B. Switch between these
displays and the odometer by
pressing the Select/Reset button
repeatedly.Each trip meter works independently,
so you can keep track of two
dif f erent distances.
To reset a trip meter, display it, and
then press and hold the Select/Reset
button until the number resets to
‘‘0.0.’’ Both trip meters will reset if
the vehicle’s battery goes dead or is
disconnected.The odometer shows the total
distance your vehicle has been
driven. It measures miles in U.S.
models and kilometers in Canadian
models. It is illegal under U.S.
federal law and Canadian provincial
regulations to disconnect, reset, or
alter the odometer with the intent to
change the number of miles or
kilometers indicated.
This shows how much f uel you have.
It may show slightly more or less
than the actual amount. Driving
uphill or make turns can cause the
needle to f luctuate or the low f uel
indicator to come on early. The
needle returns to the bottom after
you turn of f the ignition. Odometer
Trip Meter Fuel Gauge
Gauges
58
TACHOMETER SPEEDOMETER FUEL GAUGE
ODOMETER/TRIP METER TEMPERATURE GAUGE SELECT/RESET
BUTTON
Avoid driving with an extremely low
f uel level. Running out of f uel could
cause the engine to misf ire, damaging
the catalytic converter.

If your f uel cap is loose or missing, a
‘‘CHECK FUEL CAP’’ message
appears as text in the odometer/trip
meter display after you start the
engine. Turn the engine of f and
conf irm the f uel cap is installed. If it
is, loosen the cap, then retighten it at
least 3 clicks. When you restart the
engine, the message appears again.
To clear the message, press and hold
the select/reset button until the
message is replaced the odometer/
trip meter display.This shows the temperature of the
engine’s coolant. During normal
operation, the pointer should rise to
about the middle of the gauge. In
severe driving conditions, the pointer
may rise to the upper zone. If it
reaches the red (hot) mark, pull
safely to the side of the road. Turn to
page f or instructions and
precautions on checking the engine’s
cooling system.
If the system still detects a loose or
missing f uel cap, the malf unction
indicator lamp (MIL) comes on.
Turn the engine of f and check or
retighten the f uel cap at least 3 clicks.
The MIL goes out af ter 3 days of
normal driving once the cap is
tightened or replaced. If it does not
go out, have your dealer inspect the
vehicle. For more inf ormation, see
page .
210 207
Gauges
Check Fuel Cap Indicator
(odometer/trip meter message) Temperature Gauge
Inst rument s and Cont rols
59

µµ
If the MAIN switch is OFF, the
passenger’s window cannot be raised
or lowered. Keep the MAIN switch
off whenyouhavechildreninthe
vehicle so they do not injure
themselves by operating the
passenger’s window unintentionally. To open/close the driver’s
window, push the window switch
f irmly down or up to the second
detent, and release it. The window
will automatically go up or down all
the way. To stop the window, pull/
push on the window switch brief ly. If the driver’s
window senses any obstacle while it
is closing automatically, it will
reverse direction and then stop. To
close the window, remove the
obstacle, then use the window switch
again.
If your vehicle’s battery is
disconnected or goes dead, or the
driver’s window f use is removed, the
AUTO f unction will be disabled. The
power window system needs to be
reset af ter reconnecting the battery
or installing the f use.
If the power windows do not operate
properly af ter resetting, have your
vehicle checked by your dealer. Pull and hold the driver’s window
switch to close the window
completely, then hold the switch
f or a second or two more. Start the engine. Push down and
hold the driver’s window switch
until the window is f ully open.
Turn the ignition switch to ON (II)
to raise or lower either window. To
open the window, push the switch
downandholdit.Releasetheswitch
when you want the window to stop.
Pull back on the switch and hold it to
close the window. 1.
2.
AUTO AUTO REVERSE
Power Windows
Inst rument s and Cont rols
81
DRIVER’S WINDOW SWITCH
MAIN SWITCH
Closing a power window on
someone’s hands or fingers can
cause serious injury.
Make sure your passenger is
away from the window before
closing it.

Playing the AM/FM Radio
94
AM/FM BUTTON STEREO INDICATORSCAN INDICATORSCAN BUTTON
SEEK BAR
PWR/VOL
KNOB
AUTO SELECT
BUTTON
PRESET BUTTONS PWR/VOL KNOB
SEEK BUTTONS
TUNE KNOB SCAN BUTTON PRESET BUTTONS AUTO SELECT
BUTTON
TUNE KNOB
AM/FM
BUTTON
STEREO INDICATOR
U.S. LX and Canadian DX models
Canadian EX models

Playing the AM/FM Radio
Features
95
STEREO INDICATOR
PWR/VOL KNOB
SEEK BUTTONS
SCAN BUTTON PRESET BUTTONS
AUTO SELECT
BUTTON AM/FM
BUTTON
TUNE KNOB
U.S. EX models

µµ
µ µ
You can use these five methods to
f ind radio stations on a selected
band: the
preset buttons, and .
The ignition switch must be in
ACCESSORY (I) or ON (II) position.
Turn the system on by pushing the
PWR/VOL knob or the AM/FM
button. Adjust the volume by turning
thesameknob.
The band and f requency that the
radio was last tuned to is displayed.
To change bands, press the AM/FM
button. On the FM band, ST will be
displayed if the station is broadcast-
ing in stereo. Stereo reproduction on
AM is not available.
Use the TUNE knob to
tune the radio to a desired f requency.
Turn the knob right to tune to a
higher f requency, or lef t to tune to a lower f requency.
The SEEK f unction
searches up and down from the
current f requency to f ind a station
with a strong signal. To activate it,
press either ( or ), then
release it.
The SCAN f unction
samples all stations with strong
signals on the selected band. To
activate it, press the SCAN button,
then release it. You will see SCAN in
the display. The system will scan f or
a station with a strong signal. When
it f inds one, it will stop and play that
station f or about 5 seconds (LX and
DX models) or 10 seconds (EX
model).
If you do nothing, the system will
then scan f or the next strong station
and play it f or 5 seconds (LX and DX
models) or 10 seconds (EX models).
When it plays a station you want to listen to, press the SCAN button
again.
Each preset button can
store one f requency on AM, and two
f requencies on FM.
Select the desired band, AM or
FM. FM1 and FM2 let you store
two f requencies with each preset
button.
UsetheTUNE,SEEK,orSCAN
function to tune the radio to a
desired station.
Pick a preset button, and hold it
until you hear a beep.
Repeat steps 1 through 3 to store a
total of six stations on AM and
twelve stations on FM.
On all models except EX, the preset
f requencies will be lost if your
vehicle’s battery goes dead, is
disconnected, or the radio f use is
removed. 2.
3.
4. 1.
To Play the Radio
To Select a Station
TUNE,SEEK,SCAN, AUTO SELECT
TUNE SEEK
SCAN
Preset
Playing the AM/FM Radio
96

µµ
µ
If you are
traveling far from home and can no
longer receive your preset stations,
you can use the auto select feature to
find stations in the local area. These two
modes adjust the strength of the
sound coming f rom each speaker.
BAL adjusts the side-to-side strength,
while FAD adjusts the f ront-to-back
strength.
Use
the TRE/BAS/SUB-W modes to
adjust the tone to your liking.
Press the A. SEL button. ‘‘A.SEL’’
f lashes in the display, and the system
goes into scan mode f or several
seconds. It stores the f requencies of
six AM, and twelve FM stations in
the preset buttons.
You will see a ‘‘0’’ displayed af ter
pressing a preset button if auto
select cannot f ind a strong station f or
every preset button.
If you do not like the stations auto
select has stored, you can store
other f requencies on the preset
buttons as previously described. press the
A. SEL button. This restores the
presets you originally set.
Press the MODE or SOUND knob
repeatedly to display the Bass (BAS),
Treble (TRE), Balance (BAL), Fader
(FAD), and Sub-Woof er (SUB-W)
settings.
Eachmodeisshowninthedisplayas
it changes. Turn the MODE or
SOUND knob to adjust the setting to
your liking. When the level reaches
the center, you will see ‘‘C’’ in the
display. The system will
automatically return the display to
the selected audio mode about 5
seconds af ter you stop adjusting a
mode.To turn of f auto select,AUTO SELECT Balance/Fader
T reble/Bass/Sub-Woof er
Adjusting the Sound
Playing the AM/FM Radio
Features
97

Your vehicle is capable of receiving
XM
Satellite Radio anywhere in the
United States, except Hawaii and
Alaska.
XM
is a registered trade mark of
XM Satellite Radio, Inc.
Satellite radio is only available on U.S.
models.
U.S. EX models
Satellite Digital Radio
Playing the XM Satellite Radio
100
TUNE
KNOB
PWR/VOL
KNOB
CATEGORY INDICATOR
CATEGORY
BUTTONS
XM BUTTON
SCAN
BUTTON PRESET
BUTTONSCHANNEL
INDICATOR
DISPLAY BUTTON
TM

µ
µ
µThe scan f unction samples
all channels f or 5 seconds. To
activate the f unction, push the SCAN
button. Push it again to get out of the
sequence.
Use the TUNE, SEEK or SCAN
function to tune the radio to a
desired channel.
The
SEEK/SKIP f unction selects the
various categories in XM, such as
Jazz/Blues, Rock, Classical, etc.
Push the to change the
category f orward. Push the to
change the category backward. To
search f or channels within a
category, turn the TUNE knob
clockwise. Each preset button can
store one channel in XM1 and one in
XM2. Push the XM button. (You will see
XM1 or XM2.)
Pick a preset button and hold it
until you hear a beep.
Repeat steps 1 to 3 to store a total
of six stations each on XM1 and
XM2.
1.
2.
3.
4. SCAN
SEEK /SK IP (CA T EGORY)
Preset
Playing the XM Satellite Radio
102
TM