ignition HONDA FIT 2007 1.G Service Manual

When you turn the ignition switch to
the START (III) position, you do not
hear the normal noise of the engine
trying to start. You may hear a
clicking sound or series of clicks, or
nothing at all.
Check these things:
Check the transmission interlock.
If you have a manual transmission,
the clutch pedal must be pushed
all the way to the floor or the
starter will not operate. With an
au tomatic transmission, it must be
in Park or neutral.
Turn the ignition switch to the ON
(II) position. Turn on the
headlights, and check their
brightness. If the headlights are
very dim or do not come on at all,
the battery is discharged. See on page .
You can hear the starter motor
operating normally, or the starter
motor sounds like it is spinning
f aster than normal, but the engine
does not start up and run. You hear nothing, or almost
nothing. The engine’s starter
motor does not operate at all, or
operates very slowly.
Diagnosing why the engine won’t
start f alls into two areas, depending
on what you hear when you turn the
ignition switch to the START (III)
position:
Make sure the wire support ring is
ontheoutersideof thetirevalve
as shown.
3.
214
Changing a Flat Tire, If the Engine Won’t Start
Nothing Happens or the Starter
Motor Operates Very Slowly
Jump Starting
If the Engine Won’t Start
212
WIRE SUPPORT RING

Turn the ignition switch to the
START (III) position. If the
headlights do not dim, check the
condition of the fuses. If the fuses
areOK,thereisprobably
something wrong with the
electrical circuit for the ignition
switch or starter motor. You will
need a qualified technician to
determine the problem. See
on page .
If the headlights dim noticeably or
go out when you try to start the
engine, either the battery is
discharged or the connections are
co rroded. Check the condition of the
battery and terminal connections
(see page ). You can then try
jump starting the vehicle from a
booster battery (see page ). In
this case, the starter motor’s
speed sounds normal, or even faster
than normal, when you turn the
ignition switch to the START (III)
position, but the engine does not run.
Are you using the proper starting
procedure? Refer to
on page .
Are
you using a properly coded
key? An improperly coded key will
cause the immobilizer system
indicator in the instrument panel
to blink rapidly (see page ). Do
you have fuel? Check the fuel
gauge; the low fuel indicator may
not be working.
There may be an electrical
problem, such as no power to the
fuel pump. Check all the fuses
(see page ).
Ifyoufindnothingwrong,youwill
need a qualified technician to find
the problem. See
on page .
226
203 214 76
148 221
226
If theEngineWon’tStart
Emergency T owing T he Starter Operates Normally
Starting the
Engine Emergency
Towing
T aking Care of t he Unexpect ed
213

If your vehicle has an automatic
transmission, the malfunction
indicator lamp may also come on
with the ‘‘D’’ indicator.
If
you have recently refueled your
vehicle, the indicator coming on
could be due to a loose or missing
fu el fill cap. You will also see a
‘‘CHECK FUEL CAP’’ message on
the information display. Tighten the
cap until it clicks at least once.
Tightening the cap will not turn the
indicator off immediatel y; it can take
several days of normal driving. If
the indicator comes on repeatedly,
even though it may go off as you
continue driving, have your vehicle
checked by a dealer as soon as
possible.
If
this indicator comes on
while driving, it means one
of the engine’s emissions control
systems may have a problem. Even
though you may feel no difference in
your vehicle’s performance, it can
reduce your fuel economy and cause
increased emissions. Continued
operation may cause serious damag e.
Your vehicle has certain ‘‘readiness
codes’’ that are part of the on-board
diagnostics for the emissions
systems. In some states, part of the
emissions testing is to make sure these
codes are set. If they are not
set, the test cannot be completed.
If the battery in your vehicle has
been disconnected or gone dead,
these codes are erased. It can take
several days of driving under various
conditions to set the codes again.
To check if they are set, turn the
ignition switch to the ON (II)
position, without starting the engine.
The malfunction indicator lamp will
come on for 20 seconds. If it then
goes of f , the readiness codes are set.
If it blinks f ive times, the readiness
codes are not set. If possible, do not
take your vehicle for a state
emissions test until the readiness
codes are set. Ref er to for more
inf ormation (see page ). 240
Malf unction Indicator L amp
Readiness Codes State
Emissions T esting
T aking Care of t he Unexpect ed
219
If you keep driving with the
malf unction indicator lamp on, you can
damage your vehicle’s emissions
controls and engine. Those repairs may
not be covered by your vehicle’s
warranties.

However, if the brake pedal does not
feel normal, you should take
immediate action. A problem in one
part of the system’s dual circuit
design will still give you braking at
two wheels. You will feel the brake
pedal go down much farther before
the vehicle begins to slow down, and
you will have to press harder on the
pedal.
If you must drive the vehicle a short
distance in this condition, drive
slowly and carefully.
Slow
down by shifting to a lower
gear, and pull to the side of the road
when it is safe. Because of the long
distance needed to stop, it is
hazardous to drive the vehicle. You
should have it to wed and repaired as
soon as possible (see
on page ).
The
brake system indicator normally
comes on when you turn the ignition
switch to the ON (II) position, and as
a reminder to check the parking
brake. It will stay on if you do not
fully release the parking brake.
If the brake system indicator comes
on while driving, the brake fluid level
is probably low. Press lightly on the
brake pedal to see if it feels normal.
If it does, check the brake fluid level
thenexttimeyoustopataservice
station (see page ). If the ABS indicator comes on with
the brake system indicator, have
your vehicle inspected by your
dealer immediately.
If the f luid level is low, take your
vehicle to a dealer, and have the
brake system inspected f or leaks or
worn brake pads/shoes. 185
226Emergency
Towing
Brake System Indicator
220
Canada
U.S.

If something electrical in your
vehicle stops working, check for a
blown fuse first. Determine from the
chart on pages and , or the
diagram on the f use box lid, which
f use or f uses control that device.
Check those f uses f irst, but check all
the f uses bef ore deciding that a
blown f use is the cause. Replace any
blown f uses, and check if the device
works.
Turn the ignition switch to the
LOCK (0) position. Make sure the
headlights and all other
accessories are of f .
Remove the cover f rom the f use
box. Check each of the large f uses in
the under-hood f use boxes by
looking through the top at the wire
inside. Removing these f uses
requires a Phillips-head
screwdriver.
Check the smaller f uses in the
primary under-hood f use box and
all the f uses in the interior f use
box by pulling out each one with
the f use puller provided in the
interior f use box.
3.
1.
2. 4.
224 225
Fuses
Checking and Replacing Fuses
222
FUSE
BLOWN FUSE PULLER

ÎÎ
Î
Î
µ
µ µ
µ
µ
µ
Î
Î
No.
No. Circuits Protected Amps. Amps. Circuits Protected
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
26
27
28
29
30
31
32
33
1
2
3
4
5
6
7
8
9 Back Up Light
Not Used
IG METER
Turn Light
Not Used
Front Wipers
SRS
Daytime Running Light
Rear Defogger
10 A
10 A
10 A
30 A
10 A
(7.5 A) 20 A 7.5 A
15 A
10 A
10 A
15 A
20 A
20 A
20 A
(10 A)
(20 A) 10 A
10 A
7.5 A
7.5 A 15 A
(20 A) 20 A
7.5 A 15 A
15 A HAC
Fuel Pump
Rear Wiper
SRS
IGP
Left Rear Power Window
Right Rear Power Window
Right Front Power Window
Daytime Running Light
Not Used
Not Used
Fog Light
Small Light
LAF
Not Used
ABS
ACC Radio
ACC Socket
Power Door Lock
Driver’s Power Window
Not Used
LAF
DBW
Ignition Coil
1 : If equipped
2 : Canadian models
2 2
1
1
Fuse Locations
224
INTERIOR FUSE BOX

Î
Î
No.Amps. Circuits Protected No. Amps.
Amps. Circuits Protected Circuits Protected
1
2
3
4
5
6
7
8
80 A Battery 9
10
11
12
13
14
15
16 30 A
30 A
30 A
20 A
20 A
10 A
30 A
15 A
80 A
60 A
50 A
30 A
40 A
40 A
(30 A) 10 A Battery
EPS
Ignition
ABS
Blower Relay
Power Window
(HAC Option)
Back Up Small Light
Cooling Fan
Condenser Fan, MG Clutch
Right Headlight
Left Headlight
Hazard
ABS F/S
Horn, Stop
: If equipped
Fuse Locations
T aking Care of t he Unexpect ed
225
Primary Fuse Box
PRIMARY
UNDER-HOOD FUSE BOXES
Secondary Fuse Box (On the battery)

µµ
If your vehicle needs to be towed,
call a prof essional towing service or
organization. Never tow your vehicle
with just a rope or chain. It is very
dangerous.
The operator
loads your vehicle on the back of a
truck. Therearetwowaystotowyour
vehicle: If , due to damage, your vehicle must
be towed with the f ront wheels on
the ground, do this:
Release the parking brake.
Shif t the transmission to neutral.
The tow
truck uses two pivoting arms that go
under the tires (f ront) and lif t them
of f the ground. The other two tires
remain on the ground. Turn of f the engine. ShifttoD,thentoN.
Start the engine.
Release the parking brake. Leave the ignition switch in the
ACCESSORY (I) position so the
steering wheel does not lock.
Leave the ignition switch in the
ACCESSORY (I) position so the
steering wheel does not lock.With the f ront wheels on the ground,
do not tow the vehicle more than 50
miles (80 km), and keep the speed
below35mph(55km/h).
Manual transmission:
Automatic transmission:
Flat -bed Equipment
Wheel-lif t Equipment
T his is the best way to
transport your vehicle.
T his is an
acceptable way to tow your
vehicle.
Emergency Towing
226
Improper towing preparation will
damage the transmission. Follow the
above procedure exactly. If you cannot
shif t the transmission or start the
engine (automatic transmission), your
vehicle must be transported with the
f ront wheels of f the ground.

If your vehicle gets stuck in sand,
mud, or snow, call a towing service
to pull it out (see page ).
For very short distances, such as
f reeing the vehicle, you can use the
detachable towing hook that mounts
on the anchor in the f ront bumper.
To use the towing hook:Take the towing hook and the
extension out of the tool kit in the
cargo area.
Lift the upper part of the cover
f rom the bumper by pushing the
lower part with your f inger. Put a
cloth into the space behind the
upper part of the cover. Using the
extension, remove the cover f ully.
1.
2.
226
CONT INUED
Emergency Towing, If Your Vehicle Gets Stuck
If Your Vehicle Gets Stuck
T aking Care of t he Unexpect ed
227
Trying to lif t or tow your vehicle by the
bumpers will cause serious damage.
The bumpers are not designed to
support the vehicle’s weight.
The steering system can be damaged if
the steering wheel is locked. Leave the
ignition switch in the ACCESSORY (I)
position, and make sure the steering
wheel turns f reely bef ore you begin
towing.

Thediagramsinthissectiongive
you the dimensions and capacities of
your vehicle and the locations of the
identif ication numbers. It also
includes inf ormation you should
know about your vehicle’s tires and
emissions control systems.................
Identif ication Numbers .230
................................
Specif ications .232
DOT Tire Quality Grading
......................
(U.S. Vehicles) .234
Unif orm Tire Quality ..................................
Grading .234
.................................
Treadwear .234
......................................
Traction .234
.............................
Temperature .235
.................................
Tire Labeling .236 .......................
Emissions Controls .237
.....................
The Clean Air Act .237
Crankcase Emissions Control
....................................
System .237
Evaporative Emissions Control ....................................
System .237
Onboard Ref ueling Vapor ................................
Recovery .237
...
Exhaust Emissions Controls .238
....................
PGM-FI System .238
Ignition Timing Control
................................
System .238
Exhaust Gas Recircuration ...................
(EGR) System .238
Three Way Catalytic ...........................
Converter .238
....................
Replacement Parts .238
..
Three Way Catalytic Converter .239
..............
State Emissions Testing .240
T echnical Inf ormation
Technical Inf ormation
229