light HONDA INSIGHT 2010 2.G Repair Manual

Your vehicle is equipped with f ront
disc brakes. The brakes on the rear
wheels are drum. A power assist
helps reduce the ef f ort needed on
thebrakepedal.TheABShelpsyou
retain steering control when braking
very hard.
Resting your f oot on the pedal keeps
the brakes applied lightly, builds up
heat, reduces their ef f ectiveness and
reduces brake pad lif e. In addition,
f uel economy can be reduced. It also
keeps your brake lights on all the
time, conf using drivers behind you.Check the brakes after driving
through deep water. Apply the
brakes moderately to see if they f eel
normal. If not, apply them gently and
f requently until they do. Be extra
cautious in your driving.
Constant application of the brakes
when going down a long hill builds
up heat and reduces their
ef f ectiveness. Use the engine to
assist the brakes by taking your f oot
of f the accelerator and downshif ting
to a lower speed.
Braking System
324
—
—y
y
)"yy
2010 Insight

If you have the skills and tools to
perf orm more complex maintenance
tasks on your vehicle, you may want
to purchase the service manual. See
page f or inf ormation on how to
obtain a copy, or see your dealer. This section explains why it is
important to keep your vehicle well
maintained and how to f ollow basic
maintenance saf ety precautions.
This section also includes
instructions on how to read the
maintenance minder messages on
the multi-information display, and
instructions f or simple maintenance
tasks you may want to take care of
yourself .......................
Maintenance Saf ety .336
....................
Maintenance Minder . 337
..............................
Fluid Locations .347
........................
Adding Engine Oil .348
.........
Changing the Oil and Filter . 350
..............................
Engine Coolant .353
....................
Windshield Washers .355
....
Automatic Transmission Fluid . 356
Continuously Variable ............
Transmission (CVT) . 356
....................................
Brake Fluid .357
.............................................
Lights .359
................................
Roof Antenna .369
................
Cleaning the Seat Belts . 369
.....................................
Floor Mats .369
..................
DustandPollenFilter . 370
.................................
Wiper Blades .370
...............................................
Tires .375
......
Checking the 12 Volt Battery . 381
.............................
Vehicle Storage .383
Maintenance
Maint enance
335
—
—y


y
)"yy
435
2010 Insight

µµµ
µ
µ µ
Youshouldcheckthefollowing
items at the specif ied intervals. If
you are unsure of how to perf orm
any check, turn to the appropriate
page listed.
Engine oil level Check every
time you fill the fuel tank. See
page .
Engine coolant level Check the
radiator reserve tank every time
youfillthefueltank.Seepage .
Automatic transmission Check
the f luid level monthly. See page .
Brakes Check the f luid level
monthly. See page .
Tires Check the tire pressure
monthly. Examine the tread f or
wear and foreign objects. See page . Lights Check the operation of
the headlights, parking lights,
taillights, high-mount brake light,
turn signals, brake lights, and
license plate light monthly. See
page .
According to state and federal
regulations, Honda will not deny a
claim f or emissions warranty
coverage simply because you did not
maintain the vehicle or do not have
maintenance records to show that
you did. However, any part of that
f ails because of abuse or lack of
required maintenance will not be
covered by this warranty. U.S. Vehicles:
289
356 357
375 359
288
CONT INUED
Owner’s Maintenance Checks
Maintenance, replacement, or
repair of emissions control
devices and systems may be done
by any automotive repair
establishment or individual using
parts that are ‘‘certif ied’’ to EPA
standards.
Maintenance Minder
Maint enance
345
—
—y


y
)"yy
2010 Insight

CONT INUED
Open the hood.
Your vehicle has halogen headlight
bulbs. When replacing a bulb, handle
it by its base, and protect the glass
f rom contact with your skin or hard
objects. If you touch the glass, clean
it with denatured alcohol and a clean
cloth. Theheadlightswereproperlyaimed
when your vehicle was new. If you
regularly carry heavy items in the
cargo area, readjustment may be
required. Adjustments should be
done by your dealer or another
qualif ied technician.
To change the bulb on the right
side, remove the upper part of the
windshield washer reservoir tank.
Use a f lat-tipped screwdriver to
remove the holding clip, then
remove the upper part by pulling it
straight up.Remove the electrical connector
f rom the cover by pushing on the
tab to unlock it, then slide the
connector of f the cover.
Remove the cover on the back of
the headlight assembly by turning
it counterclockwise.
1.
2.
3.
Headlight A iming
Replacing a Headlight Bulb
Lights
High Beam Headlight
Maint enance
359
HOLDING CLIP
CONNECTOR
Halogen headlight bulbs get very hot
when lit. Oil, perspiration, or a scratch
on the glass can cause the bulb to
overheat and shatter.
—
—y


y
)"yy
2010 Insight

Remove the electrical connector
f rom the bulb by pushing on the
tab and pulling the connector
down.Remove the bulb f rom the
headlight assembly by turning it
one-quarter turn counterclockwise.Install the new bulb, and turn it
one-quarter turn clockwise to lock
it in place.
Push the electrical connector back
onto the bulb. Make sure it is on
all the way.
Reinstall the cover over the back
of the headlight assembly and turn
it clockwise to lock it in place.
Push the electrical connector back
onto the cover.
Turn on the headlights to test the
new bulb.
4.
5. 6.
7.
8.
9.
Lights
360
BULB
COVER
CONNECTOR
—
—y


y
)"yy
2010 Insight

Install the new bulb, and turn it
one-quarter turn clockwise to lock
it in place.
Push the electrical connector back
onto the bulb. Make sure it is on
all the way.
Turn on the headlights to test the
new bulb.
Install the upper part of the
windshield washer reservoir tank
in the reverse order of removal.
Remove the bulb f rom the
headlight assembly by turning it
one-quarter turn counterclockwise. Remove the electrical connector
f rom the bulb by pushing on the
tab and pulling the connector
down. Open the hood.
(Right side)
3. 4.
5.
6.
2. 1.
10.
Lights
L ow Beam Headlight
Maint enance
361
BULB
CONNECTOR
—
—y

y
)"yy
2010 Insight

Open the hood.
To change the bulb on the right
side, remove the upper part of the
windshield washer reservoir tank.
Use a f lat-tipped screwdriver to
remove the holding clip, then
remove the upper part by pulling it
straight up.Remove the socket from the
headlight assembly by turning it
one-quarter turn counterclockwise.
Pull the bulb straight out of its
socket. Push the new bulb straight
into the socket until it bottoms.Install the socket back into the
headlight assembly. Turn it
clockwise to lock it in place.
Turn on the lights to make sure
the new bulb is working.
Install the upper part of the
windshield washer reservoir tank
in the reverse order of removal. (Right side)
6.
1. 2.
3.4.
5.
Lights
Replacing a Front Parking Light
Bulb
362
BULB
HOLDING CLIP
SOCKET
—
—y

y
)"yy
2010 Insight

Place a cloth on the edge of the
light assembly garnish. Remove
the cover by caref ully prying in
the notch on its lef t edge with a
f lat-tipped screwdriver.Remove the socket f rom the f ront
turn signal light assembly by
turning it one-quarter turn
counterclockwise.Pull the bulb straight out of its
socket. Push the new bulb straight
into the socket until it bottoms.
Insert the socket back into the
f ront turn signal light assembly.
Turn it clockwise to lock it in place.
Turn on the lights to make sure
the new bulb is working.
Install the light assembly in the
reverse order of removal. Make
sure to secure the bolt.
Install the garnish in the original
position securely.
Remove the bolt and pull the f ront
turn light assembly f rom the
bumper while taking the tab out
f rom the holder. 5.
6.
1. 7.
8.
3. 4.
2.
Lights
Replacing the Front T urn Signal
Light Bulb
Maint enance
363
TAB
BOLT
GARNISH
NOTCH
BULB
—
—y

y
)"yy
2010 Insight

Open the hood.
Remove the socket from the
headlight assembly by turning it
one-quarter turn counterclockwise.Pull the bulb straight out of its
socket. Push the new bulb straight
into the socket until it bottoms.
Install the socket back into the
headlight assembly. Turn it
clockwise to lock it in place.
Turn on the lights to make sure
the new bulb is working.
2. 3.
4.
5.
1.
Lights
Replacing a Front Side Marker
Light Bulb
364
BULB
SOCKET
—
—y

y
)"yy
2010 Insight

CONT INUED
Open the hatch.
Push on the area of the trim as
shown in the illustration above to
detach the upper hooks f rom the
light assembly.Pry on the gap between the trim
and light assembly caref ully with a
f lat-tipped screwdriver to detach
the lower hooks.
Make sure that all hooks are
removed f rom the light assembly.
Unclip the top half of the trim
fromthebodybypullingitout.
Then unclip the bottom half.
1.
2.
3.
4.
Lights
Replacing the Rear Bulbs
Maint enance
365
HOOKS
TRIM
HOOKS CLIP
CLIP
—
—y

y
)"yy
2010 Insight