oil HONDA INTEGRA 1998 4.G Workshop Manual
[x] Cancel search | Manufacturer: HONDA, Model Year: 1998, Model line: INTEGRA, Model: HONDA INTEGRA 1998 4.GPages: 1681, PDF Size: 54.22 MB
Page 1057 of 1681

I
I
ChargingLeak Test
Use only service equipment that is U.L.-listed and is cer-
tified to meet the requirements of SAE J2210 to remove
HFC-134a (R-134a) from the air conditioner system.
CAUTION: Exposure to air conditioner refrig6rant and
lubricant vapol or mist can irritate eyes. nose and
throat. Avoid broating the air conditione. relrigerant
and lubricant vapor o; mist.
lf accidental system discharge occurs, ventilate work
area before resuming service.
R-134a service equipment or vehicle air conditioner sys-
tems should not be pressure tested or leak tested with
compressed air.
@ some mixtures of air and R-1348 have
been shown to be combustible at €levat€d pre3sures
and can rosult in fire or explosion causing iniury or
property damage. Never use compressed air to pressure
test R-134a s€rvics oquipment or vehicle air conditioner
Systems.
Additional health and safety information may be
obtained from the refrigerant and lubricant manufac-
rures.
Connect a R-134a refrigerant Recovery/Recycling/
Charging System to the vehicle, as shown in the pre-
vious column, following the equipment manufactur-
er's instructions.
NOTE: Be sure to install the same amount of new
refrigerant oil back into the A/C system before
charging.
Open high pressure valve to charge the system to
the specified capacity, then close the supply valve,
and remove the charging system couplers.
R€frigerani capacity: 700 1o g 124.7 llroz)
Check the system for leaks using a R-134a refriger-
ant leak detector with an accuracy of 14 g (0.5 oz)
per year or better.
lf you find leaks that require the system to be
opened (to repair or replace houses. fittings, etc.),
recover the system according to the Recover
Procedure on page 22-22.
After checking and repairing leaks, the system must
be evacuated (see System Evacuation on page 22-
38).
JUse only service equipment that is U.L.-listed and is cer-
tified to meet the requirements of SAE J2210 to remove
HFC-134a (R-134a) from the air conditioner system.
CAUTION: Exposure to air conditioner r€frigsrant and
lubricant vapol or mist can irritate eyos, nose and
throat. Avoid broathing the air conditioner reftigerant
and lubricant vapor or mist.
lf accidental system discharge occurs, ventilate work
area before resuming service. Additional health and
safety information may be obtained from the refrigerant
and lubricant manufactures.
Retrigerant capscity: 700 % g (2,[.7 i.sozl
CAUTION: Do nol overcharge tho sy3tem; the compres-
sor will b6 damaged.
Connect a R-134a refrigerant Recovery/Recycling/
Charging System to the vehicle, as shown. tollowing the
equipment manufacturer's instructions.
n6covery/Rocycling/Charging Svslem
LOW-PRESSURESIDE
22-39
Page 1063 of 1681

Troubleshooting
Schematic Symbolsym
BATTEBY
tr3
o-
GROUNDGround terminal Componenr ground
I il
FUSE
rhtdl
l9l.|
CIGARETTE LIGHTER
,A
lrl
Y
RESISTOR
+
T
VARIABLE RESISTOR
TD
=rX
ttf
THERMISTOR
/b'
t=l
v
IGNITION SWITCH
1-\-T- l.--
BULB
A
Y
HEATER
-h
t=l
tr
MOTOR
0
PUMP
A
Y
CIRCUIT EREAKER
I
t
Y
HORN
+
DIODE
+
SPEAKER, BUZZER
D
Mast
Y
ANTtiNNA
T,
TRANSISTOR (Tr)
ll
+1^'l
)
Wire Color Codes
The following abbreviations are used to identify wire
colors in the circuit schematics:
WHT ............ White
YE1 .............. Yellow
81K .............. Black
B1U .............. Blue
GRN ............. Green
RED .............. Red
ORN ............. Orange
PNK .............. Pink
BRN .............. Brown
GRY ............. Gray
PUR .............. Purple
LT BLU ......... Light Blue
LT GRN ......... Light Green
The wire insulation has one color or one color with
another color stripe.'The second color is the stripe.
WHT/BLK
,//,aI,//t- /
R
BELAY lln noNormally open relayrmal position)
Normally closed relay
-tr-f,-
l=T= |
til
trf
CONDENSER
I
T
SWITCH {ln nrNormally openswitch
I
/6\
v
I
)rmal position)Normally closed
I
A
w
I
LIGHT EMITTINGDIODE (LEDI
AJ"
YT
CONNE
V
I
CTIONOutput
J,
CONNECTOR
+>-
l-l'l
REED SWITCH
.K
Irr ]
Y
Page 1070 of 1681

Connector ldentification and Wire Harness Routing
JHow to ldenti{v Connectors:
ldentification numbers have been assigned to all connectors. The number is preceded by the letter "C" for connectors,"G" for single ground terminals ot "f" lor single non-ground terminals.
/
Location
HarnossEngine CompartmentDashboardOthers (Floor, Door,
Trunk. Rooll
Starter cablesT1, T2, and @
Battery ground cableG1 and O
Engine ground cable A
G2
Engine ground cable BT4
G3
Under-hood ABS fuse/relav box cableT5 and @
Engine wire harnessC101 through C134
T101 and T102
G101
A,/C wire harnessC151 through C156
G151
Engine compartment wire harnessC301 through C320
G301
Main wire harnessC201 through C223
G20'l and G202
C40l through C454
G401
Rear wire harnessC501 through C536
G501 (Sedan), G502
and G503
Dashboard wire harnessC551 through C569
G551
Driver's door wire harnessC601 through C612
Front passenger's door wire harnessC626 through C634
Left rear door wire harness (Sedan)C65l through C654
Right rear door wire harness (SedanlC656 throughc659
Roof wire harnessC661 through C667
Heater sub-harness AC671 through C677
Heater sub-harness BC68l through C684
ABS sub-harnessC701 through C706
G701 and G702
Hatch wire harness (Hatchback)C751 through C758
Spoiler sub-harness {Hatchback)C761 through C763
Rear window defogger ground wire
(Hatchback)
c11 l
G77'l
SRS main harnessC801 through C808
G801
23-13
Page 1073 of 1681

Connector ldentification and Wire Harness Routing
Connectot or
Terminal
Numbel of
CavitiesLocationConnects toNotes
c'to 1
c102
c103
c'1 04
c105
c106
c 107
c108
c108
c109
c110
c112
c113
c'r 14
c115
c116
c117
c118
ct'l9
c119
c120
c121
c122
c124
c't 26
c127
c128
c129
c130
c111
4
10
14
6
I
1
2
2
10
2
3
2
J
4
3
3
2
2
I
3
2
2
2
2
2
I
2
14
Right side of engine compartment
Right side of engine compartment
Right side ot engine compartment
Right side of engine compartment
Right side oI engine compartment
Right side of engine
Right side of engine
Transmission
Transmission
Middle ot engine
Middle ot engine
Right side of engine
Right side of engine compartment
Middle rear of engine compartment
N4iddle of engine
N4iddle ol engine
Middle oI engine
Nliddle ot engine
Middle of engine
Lelt side of engine
Left side of engine
Middle of engine
Middle oI engine
Middle of engine
Middle of engine
Middle ot engine
Left side of engine compartment
Lelt side ot engine compartment
Left side of engine compartment
Transmission
Transmission
Transmission
Main wire harness (C221)
Main wire harness (C222)
Main wire harness 1C223)
lvlain wire harness (C220)
Starter solenoid
Engine coolant temperature (ECT)
sensor
Engine coolant temperature (ECT)
gauge sending unit
Back-up light switch
Lock-up control solenoid valve A and B
Distributor
Crankshatt speed fluctuation (CKF)
sensor
Engine coolant temperature (ECT)
switch
Vehicle speed sensor (VSS)
Primary HO2S
MAP sensor
Throttle position (TP) sensor
ldle air control (lAC) valve
EVAP purge control solenoid valve
Engine oil pressure switch
Alternator
Alternator
lntake air temperature (lAT) sensor
No. 1 fuel injector
No. 2 fuel injector
No. 3 fuel injector
No. 4 fu€l injector
Junction connector
Engine compartment wire harness
(c304)
Engine compartment wire harness
(c30s)
Shift control solenoid valve A and B
Countershaft speed sensor
lvlainshaft speed sensor
M/T
NT
USA
Canada
Afi
Afi
T101
T102
Left side oI engine
Right side of engine compartment
Alternator
Under hood fuse/relay box
G'1 01Right side oI engineEngine ground. via engine wire
harness
Engine Wire Harness (B188l enginel
23-16
Page 1075 of 1681

Connector ldentification and Wire Harness Routing
Engine Wire Harness (B18Cl enginel
Connectol ol
Terminal
Number of
CavitiesLocationConnects toNotes
c 101
c102
c103
c104
c105
c106
c101
c108
cr09
c110
c'r 11
cl12
c1't3
c114
c115
c116
cl17
c118
c119
c119
c120
cI2'l
cl24
c126
c127
cl31
c132
c133
c134
10
14
3
1
2
1
2
10
2
'I
3
2
2
2
I
1
2
2
?
3
2
14
Right side of engine compartment
Right side of engine compartment
Right side of engine compartment
Right side ol engine compartment
Right side of engine compartment
Righr side oI engine
Right side of engine
Transmission
Middle of engine
Middle of engine
Right side of engine
Right side of engine compartment
Middle rear of engine compartment
Middle of engine
Middle of engine
Middle of engine
Middle of engine
i/iddle of engine
Left side ot engine
Lelt side ot engine
Middle ot engine
Middle of engine
Middle of engine
Middle of engine
Middle of engine
Left side of engine companment
Left side of engine compartment
Lelt side of engine compartment
Right side of engine
Right side of engine
Middle of engine
Middle of engine
lvlain wire harness (C221 )
Main wire harness {C222)
Main wire harness (C223)
Main wire harness (C220)
Starter solenoid
Engine coolant temperature (ECT)
sensor
Engine coolant temperature (ECT)
gauge sending unit
Back-up light switch
Distributor
Crankshalt speed fluctuation (CKFI
sensor
Engine coolant temperature {ECT)
switch
Vehicle speed sensor (VSS)
Primary HO2S
MAP sensor
Throttle position {TP) sensor
ldle air control (lAC) valve
EVAP purge control solenoid valve
Engine oil pressure switch
Alternator
Alternator
Intake air temperature llAT) sensor
No. 1 fuel injector
No. 2 fuel injector
No. 3 tuel injector
No. 4 tuel injector
Junctron connector
Engine compartment wire harness(c304)
Engine companment wire harness(c30s)
VTEC solenoid valve
VTEC oil pressure switch
Knock sensor (KS)
Intake air bypass {lAB) control sole-
noid valve
USA
Canada
T101
r 102
Left side ot engine
Right side of engine compartment
Alternator
Under-hood fuse/relay box
G 101Right side of engineEngine ground, via engine wire
naaness
23-18
Page 1101 of 1681

Gonnector ldentification and Wire Harness Routing
Hatch Wire Halness (Hatchback)
Connactoa oa
Tcrminal
Numb€r of
CavitiesLocationConnects toNot€s
c751
c152
c754
c755
c757
c758
2
1
2
2
Bight side of cargo area
Right side of cargo area
Right side of rear window
Right side of hatch
Middle of hatch
Middle of hatch
Right side of cargo area
Middle of hatch
Rear wire harness {C526}
Rear wire harness (C525)
Rear window defogger (+)
Spoiler sub-harness (C761 )Rear window wiper motor
High mount brake light
Rear wire harness (C527)
Tailgate open switch
Right side of hatchBody ground, via hatch wire
narness
*1: Hatchback with rear sDoiler
Spoiler Sub-harness (Hatchback with Rear Spoilell
Connector or
Telminal
Number ot
CavitiesLocationConnects toNotes
c761
c762
c763
2
1
1
Right side of hatch
Middle of hatch
Middle of hatch
Hatch wire harness (C754)
High mount brake light { + )High mount brake light { - )
Rear Window Defogger Ground Wire {Hatchback)
Connectot or
Telminal
Number of
CavitiesLocationConnects toNotes
c7711Left side of rear windowRear window defogger (- )
G711Left side of rear windowBody ground, via rear window
defogger ground wire
23-44
Page 1102 of 1681

ltlli
,l
HATCHWIRE HARNESS
SPOILER SUB-HARNESS
REAR WINDOWDEFOGGERGROUNO WIRE
Page 1105 of 1681
![HONDA INTEGRA 1998 4.G Workshop Manual Fuses
Under-dash Fuse/Relay Box
C920 [To SRS msin harnc$ lc8{,l}lC922 [To ignition rwitchl
C923lTo main wir. harn6! (Cil,alll
C€24 [To m.in wiro hrrno$ lc,l,l2]l
lTo pow.r windowrclayl
CgNlS Oo turn HONDA INTEGRA 1998 4.G Workshop Manual Fuses
Under-dash Fuse/Relay Box
C920 [To SRS msin harnc$ lc8{,l}lC922 [To ignition rwitchl
C923lTo main wir. harn6! (Cil,alll
C€24 [To m.in wiro hrrno$ lc,l,l2]l
lTo pow.r windowrclayl
CgNlS Oo turn](/img/13/6069/w960_6069-1104.png)
Fuses
Under-dash Fuse/Relay Box
C920 [To SRS msin harnc$ lc8{,l}lC922 [To ignition rwitchl
C923lTo main wir. harn6! (Cil,alll
C€24 [To m.in wiro hrrno$ lc,l,l2]l
lTo pow.r windowrclayl
CgNlS Oo turn 3ign.l/h.z.rd rcl.yl
C919 [To root wir. hsmolr {C661ll
al Spare fusel: Option connector (+B)
2: Option conn€ctor (oash lights)3: Option connector (ACC)
4: Option connector {lG2}*: Not us€d
Fusa Number Amp!wire Color
C928 [To r..] window d.toggd r.l.yl
Compon€nt(s) or Circuit(3) Protaqtad
C92l ITo d..hbo.rd wir. h.rness lc551ll
- r-t r-'l r-'t n n r-'t n n r-1 r-'l r-l4 2321 2s 26 27 28 29 30 3t 32 33IJ IJ IJ LI LI IJ LI LJ IJ LI LJ I.J
- r-t n n r-l r-'t r-t r-'l r-1 n r-'t r-1a 12 13 14 15 t6 17 ,t8 19 20 21 22I-J LI IJ IJ tJ LI LI IJ IJ IJ LI IJ
- r-'t |;l n r-1 n |;t r-'t r-t r-1 n r-'ta 12 3 it 5 67 8 910 11
LI IJ IJ IJ LI IJ LI LI I-J LI LJ LI
1204WHT/GRNPower door lock control unit
Not used
10AGRN,4/VHTRear window washer motor
GRN/BLKRear window wioer motor
410 ARED/BLURight headlight (high beam)
10ARED/GRNLeft headlight (high beam), high beam indicator light
Not used
720A.GRN/BLKLeft rear power window motor
a204YEUBLKRight rear power window motor
15 ABLK/YELlgnition coil
10204BLU/BLKPasseflger's power window motor
l1204WHTI/ELPower window master switch, power window control unit
23-48
Page 1113 of 1681

Power Distribution
Gircuit ldentification (cont'd)
No.42 {40AiFUSE(From page 2154)
BLKBLU
ELKBLU
+- BLK/YEL -ABSconlrolunil
Bear window detoggef relay(Via re window delogger swilch)
Oplional connoctor (lc2)
(Via power mircr swilch)
UNOEF,HOOO FUSSF€LAYBOX (To page 23-55)
I
VTo page23-58
BLKWHT
I
V
/ To page 23-59
(Fuse,telay box sockel)
cRN {or REot -i-
BLK'YEL -
Recirdlalion conlrol nolof,/C lhefmoslalMods conlrol motorHealer conlrol panel
oaylime running lights relay (Canada)
near washor molor(Via rear wiper^vasher swilch)
lgnilion coil
Tuln signal/harad relay(via swrtcl)
PGM.FI main relay
SRS unil (VA)
Cruise conlrol unit
BLK,TYEL --- Alernalorr_. TcM
BLK/YEL ---t- vss- E-D Jril (JSAj
Charging syslem l€hl
UNDEB-DASH FIJSE/RELAY BOX
N0.18 (7.5A)
N0.14 (7.5A)
IGN]TION SWI'TCH
\ Acc
23-56
Page 1136 of 1681
![HONDA INTEGRA 1998 4.G Workshop Manual 1.Remove the dashboard lower cover and knee bolster(see page 23-71],, then disconnect the 2P connector
from the switch.
Check for continuity between the terminals accord-
ing to the table.
2.
3.ll nec HONDA INTEGRA 1998 4.G Workshop Manual 1.Remove the dashboard lower cover and knee bolster(see page 23-71],, then disconnect the 2P connector
from the switch.
Check for continuity between the terminals accord-
ing to the table.
2.
3.ll nec](/img/13/6069/w960_6069-1135.png)
1.Remove the dashboard lower cover and knee bolster(see page 23-71],, then disconnect the 2P connector
from the switch.
Check for continuity between the terminals accord-
ing to the table.
2.
3.ll necessary, replace the switch or adiustthe switch
position (see section 12).
Terminal
cr,t"hP;i
-_\B
RELEASED
PUSHEDoo
Clutch lnterlock Switch TestStarter Solenoid Test
1. Check for continuity between the terminals accord-
ing to the table.
HOLD_ IN COIL
23-79
I
/
-
I
-a
Coil
Teminalt\4sHousing
HOLD INO-o
PULL-INo-o
PULL_ IN COIL