ECU HONDA ODYSSEY 1999 Owner's Manual

HomeLink Universal Transmitter

1. This step erases all previously learned
codes. Perform this step before
training the transmitter for the very

first time. Press and hold the two
outside buttons until the red light
in the transmitter flashes (approximately 20 seconds).
Release the buttons.
2. Hold the end of the garage door opener remote control 1 to 3
inches from the HomeLink
transmitter. Make sure you are
not blocking your view of the redlight in the transmitter.
3. Select the transmitter button you want to train.
4. Press the button on the remote control and the button on the
transmitter at the same time. Holddown both buttons. 5. The red light in the transmitter
should begin flashing. It will flashslowly at first, then rapidly.
6. When the red light flashes rapidly, release both buttons. The
transmitter should have learned
the code from the remote control.
7. Test the transmitter button by pushing it. It should operate the
garage door.
8. Repeat these steps to train the other two transmitter buttons to
operate any other remotely-
controlled devices around your
home (lighting, automatic gate, security system, etc.).
Canadian Owners:

The remote control you are training from may stop transmitting after twoseconds. This is not long enough for
the HomeLink transmitter to learn
the code. Release and press the
button on the remote control every
two seconds until the transmitter has
learned the code.
If you are programming the
transmitter to operate a garage door or gate, it is recommended that you
unplug the motor for that device during programming. Repeatedly
pressing the remote control button could burn out the motor.
The HomeLink transmitter stores the code in a permanent memory.
There should be no need to retrain the transmitter if your vehicle's
battery goes dead or is disconnected.

Instruments and ControlsProCarManuals.comMain Menu Table of Contents s t

HomeLink Universal Transmitter

Retrainings Button

To train an already programmed transmitter button to operate a new
device:

1. Select the transmitter button you want to train.
2. Press and hold the transmitter button until the red light begins to
flash slowly (approximately 20
seconds).

3. While continuing to hold the transmitter button, place the
remote control for the device 1 to 3 inches from the HomeLink
transmitter.
4. Press and hold the button on the remote control. Hold both buttons
until the red light begins to flash
rapidly.
5. Release both buttons. The transmitter, should now be trained
to operate the device. Training With a Rolling Code
System
For security purposes, newer garage
door opening systems use a "rolling"
or variable code. If you know that
your garage door opener has a rolling code, or you have been
unable to train the transmitter afterseveral attempts, use the following
procedure. You will need someone to
help you. TRAINING
BUTTON
GARAGE DOOR
OPENER MOTOR/
CONTROL UNIT
1. Make sure you have properly completed the "Training the
Transmitter" procedure.
2. Find the 'Training" button on your garage door opener motor/controlunit. The location will vary,
depending on the manufacturer.
The manufacturer's documentation may help.

CONTINUED

Instruments and ControlsProCarManuals.comMain Menu Table of Contents s t

Seats

Third Seat Access
Convertible Second Row Bucket Seats
model
To get into or out of the third row
seat, walk between the second row

seats.
When the seat on the passenger's

side is moved to the center, walk

through the passenger's side to get
into or out of the third row seat. Bench Seat model
To get into or out of the third row seat, pull the seat-back angle
adjustment lever on the second row seat to tilt the seat-back forward.
The seat-back folds flat when you pull the angle adjustment lever. Hold
the seat-back to keep it from foldingquickly.
Make sure the seat-back is securely
locked before driving.
Instruments and ControlsSEAT-BACK ANGLE
ADJUSTMENT LEVERProCarManuals.comMain Menu Table of Contents s t

Seats

Moving the Second Row Bucket
Seat
The second row bucket seat on the
passenger's side can be moved to the
center to provide access to the thirdrow seat.
Remove the two floor covers
between the bucket seats in the second row by carefully prying on
the back edge of the covers with a
flat-tipped screwdriver. Unlock the seat from the floor by
pulling the lock release lever under
the seat cushion's front edge and lifting the rear of the seat.
Slide the seat toward the center of
the vehicle. Push the back of the seat down over
the floor hooks. Make sure the seat
is securely locked in place.

Instruments and Controls
LOCK
RELEASE LEVERProCarManuals.comMain Menu Table of Contents s t

Seats
Install the floor covers over the outer
floor hooks on the passenger's side as shown. Make sure the seat is securely
locked in place before driving. A seat
that is not locked in place could fly around and cause injury in a suddenstop or crash.
Reverse this procedure to move the
seat back to the outside.

Instruments and ControlsProCarManuals.comMain Menu Table of Contents s t

Seats

Removing the Bucket Seats in the

Second Row

Both seats can be removed to give
more cargo capacity.
To remove a seat: Pull up the seat-back angle
adjustment lever, and fold the seat-
back forward.
Unlock the seat from the floor by
pulling the lock release lever under
the seat cushion's front edge and
lifting the rear of the seat. Unhook the front of the seat from
the floor by pulling it back slightly,
then pivoting it upward.
Always remove an unlocked seat from the vehicle before driving. Aseat that is not locked in place could
fly around and cause injury in a sudden stop or crash. To reinstall the seat, hook the front
of the seat to the floor, then push the
back into the locks. Make sure both the front and the back of the seat aresecurely latched before driving.
Instruments and Controls LOCK RELEASE LEVERProCarManuals.comMain Menu Table of Contents s t

Seats

To reinstall the seat, hook the front of the seat to the floor, then push the
back into the locks. Make sure both
the front and the back of the seat are securely latched before driving. Folding the Third Seat
RELEASE BUTTON
To create more cargo space, you can fold the third seat into the floor

recess.

To fold the third seat:
1. Remove the head restraints by pushing the release buttons and
pulling the restraints out. 2. Store the head restraints in the
side cargo net. To install the side
cargo net, hook the four loops on
the net to the tabs on the left side
panel.

Instruments and ControlsProCarManuals.comMain Menu Table of Contents s t

Seats

HANDLE

3. Unlock the seat-back by pulling
the handle. Push the seat-back

forward. HANDLE
4. Pull the handle on the back of the seat cushion while you pull the
entire seat towards you with the
strap. Pivot the seat into the floor

recess.
Make sure the center shoulder belt
is stored in the holder and the outer
shoulder belts are positioned on each
hook whenever the third seat is

folded.

Make sure all items in the cargo area
are secured. Loose items can fly
forward and cause injury if you have
to brake hard. See Carring Cargo
on page 191.

CONTINUED

Instruments and ControlsProCarManuals.comMain Menu Table of Contents s t

Seats

To return the seat to the upright
position:

1. Pull the seat out of the recess by pulling on the handle and the strap.Pivot the seat forward all the way. HANDLE
2. Pull up on the handle on the seat- back, and pull the seat-back
upright with the strap. Make sure
the seat is securely locked in place.
3. Reinstall the head restraints.

Instruments and ControlsProCarManuals.comMain Menu Table of Contents s t

Service Station Procedures

If you can open the hood without
lifting the hood latch handle, or the
hood latch handle moves stiffly or does not spring back as before, the
mechanism should be cleaned and
lubricated (see page 248 ).
3. Pull the support rod out of its clipand insert the end into the hole on
the driver's side of the hood. To close the hood, lift it up slightly to
remove the support rod from the
hole. Put the support rod back into its holding clip. Lower the hood to
about a foot (30 cm) above the
fender, then let it drop.
After closing the hood, make sure it is securely latched.

CONTINUED

Before Driving

SUPPORT RODProCarManuals.comMain Menu Table of Contents s t