coolant reservoir HONDA PASSPORT 2002 2.G Owners Manual

191In Case of Emergency
find a leak, it must be repaired
before you can continue
driving. (See Towing on page
191.)
•If you don’
t find an obvious
leak, check the coolant level in
the radiator reserve tank. If the
level is below the
MIN mark, add
coolant to halfway between the
MIN and MAX marks.
•If there was no coolant in the
reserve tank, you may also
have to add coolant to the
radiator.
Let the engine cool down until
the pointer reaches the middle
of the temperature gauge, or
lower, before checking the
radiator.
Removing the radiator cap
while the engine is hot can
cause the coolant to spray
out, seriously scalding you.
Always let the engine and
radiator cool down before
removing the radiator cap.
•
If needed, add coolant to the
radiator to bring the level up to
the filler neck, and to the
reservoir up to the level
indicated on the reservoir tank. Proper equipment must be used to
prevent damage to vehicles during
any towing. State and local laws
that apply to vehicles in tow must
be followed. Get detailed towing
instructions from your Honda
dealer.
Should it become necessary to
tow your vehicle, follow these
directions.Precautions
•Before towing, make sure that
the power train, axle,
transmission, wheels and
steering system are in good
condition.
If any of these items are
damaged, a flatbed trailer must
be used.
Towing

219Care and Maintenance
(–36

C) to ensure protection
against corrosion and loss of
engine coolant from boiling.
This should be done even if
freezing temperatures are not
expected.
•Add ethylene glycol-based
antifreeze when antifreeze has
to be added because of engine
coolant loss or if more
protection against freezing at
temperatures lower than –33
F
(–36
C) is needed. Do not use
an alcohol-based or
methanol-based antifreeze, or
plain water. They boil at a
lower point, and do not provide
corrosion protection.
Thermostat
The engine coolant temperature is
controlled by a thermostat, which
stops engine coolant flow through
the radiator until a preset
temperature is reached. This
thermostat is installed in the
engine coolant inlet on the front
of the engine block. The same
thermostat is used in both winter
and summer.Brake Master Cylinder
Check the master cylinder fluid
level in the reservoir every time
you check the engine oil level.
The level should be between the
MAX and ADD level line. If the
level is lower than the
ADD level
line, fill to the
MAX level line
with
DOT-3 or DOT-4 fluid.
Other Required
Maintenance

223Care and Maintenance
Spark Plugs
Replace the spark plugs with the
type specified in the “Technical
Data” section.
Clutch
Check the clutch play at the pedal.
Lubricate the clutch pedal bushing
and clevis pin, at the intervals
shown in the Maintenance
Schedule, with water-resistant
chassis lubricant. If you hear a
squeaking noise coming from the
area of the bushing or clevis pin at
the clutch pedal arm when the
clutch pedal is depressed,
lubricate it with water-resistant
EP
chassis grease.
Check the fluid level in the clutch
reservoir at the interval shown in
the Maintenance Schedule. If the
fluid is low in the reservoir, it should be filled to the maximum
level line with
DOT-3 or DOT-4
fluid.
Fluid or Lubricant Levels
Check the fluid or lubricant level
in the brake master cylinder,
clutch master cylinder, power
steering reservoir, rear axle,
engine and transmission,
windshield washer reservoir and
engine coolant at specified
intervals.
Power Steering
Check the fluid level in the power
steering fluid reservoir as
recommended in the Maintenance
Schedule. The fluid level should
be between the “
MIN” and
“
MAX” marks on the reservoir.
Use only automatic transmission
fluid labeled
DEXRON III.