HUMMER H2 2004 Owners Manual

{CAUTION:
Snow can trap exhaust gases under your
vehicle. This can cause deadly CO (carbon
monoxide) gas to get inside. CO could
overcome you and kill you. You can not see it
or smell it, so you might not know it is in your
vehicle. Clear away snow from around the
base of your vehicle, especially any that is
blocking your exhaust pipe. And check around
again from time to time to be sure snow does
not collect there.
Open a window just a little on the side of the
vehicle that is away from the wind. This will
help keep CO out.Run your engine only as long as you must. This saves
fuel. When you run the engine, make it go a little
faster than just idle. That is, push the accelerator
slightly. This uses less fuel for the heat that you get and
it keeps the battery charged. You will need a
well-charged battery to restart the vehicle, and possibly
for signaling later on with your headlamps. Let the
heater run for a while.
Then, shut the engine off and close the window almost
all the way to preserve the heat. Start the engine
again and repeat this only when you feel really
uncomfortable from the cold. But do it as little as
possible. Preserve the fuel as long as you can. To help
keep warm, you can get out of the vehicle and do
some fairly vigorous exercises every half hour or so until
help comes.
4-55

If You Are Stuck: In Sand, Mud, Ice
or Snow
In order to free your vehicle when it is stuck, you will
need to spin the wheels, but you do not want to
spin your wheels too fast. The method known as
“rocking” can help you get out when you are stuck, but
you must use caution.
{CAUTION:
If you let your tires spin at high speed, they
can explode, and you or others could be injured.
And, the transmission or other parts of the
vehicle can overheat. That could cause an
engine compartment re or other damage.
When you are stuck, spin the wheels as little as
possible. Do not spin the wheels above 35 mph
(55 km/h) as shown on the speedometer.
Notice:Spinning your wheels can destroy parts of
your vehicle as well as the tires. If you spin the
wheels too fast while shifting your transmission
back and forth, you can destroy your transmission.
For more information about using tire chains on your
vehicle, seeTire Chains on page 5-75.
Rocking Your Vehicle To Get It Out
First, turn your steering wheel left and right. That will
clear the area around your front wheels. Your vehicle
has a Traction Control System that will activate when the
system senses that the wheels are spinning. See
Traction Control System (TCS) on page 4-9for more
information. Then, with the wheels straight ahead, shift
back and forth between REVERSE (R) and a forward
gear, spinning the wheels as little as possible. Release
the accelerator pedal while you shift, and press
lightly on the accelerator pedal when the transmission is
in gear. By slowly spinning your wheels in the forward
and reverse directions, you will cause a rocking
motion that may free your vehicle. If that does not get
you out after a few tries, you may need to be towed out.
Or, you can use your recovery loops. If you do need
to be towed out, seeTowing Your Vehicle on page 4-65.
4-56

Using the Recovery LoopsYour vehicle may be
equipped with recovery
loops at the front and rear
of your vehicle. You
may need to use them if
you are stuck off-road and
need to be pulled to
some place where you can
continue driving.
Front of Vehicle
Rear of Vehicle
4-57

{CAUTION:
These loops, when used, are under a lot of
force. Keep people away from the vicinity of
the loops and any chains or cables during use.
Always pull the vehicle straight out. Never pull
on the loops at a sideways angle. The loops
could break off and you or others could be
injured from the chain or cable snapping back.
Notice:Never use the recovery loops to tow the
vehicle. Your vehicle could be damaged and it would
not be covered by warranty.
4-58

First Aid Kit and Tool Kit
Your vehicle may have a rst aid kit and/or a tool kit
located in the storage bin behind the spare tire. They are
held in place with a hook and loop fastener strap.If your vehicle has the tool kit, the kit includes a
ashlight, a tire pressure gage and a multi-purpose
tool set.
4-59

The tire pressure gage has
a reset button in the gage
stem. After taking a
pressure reading, press
the button to reset
the gage to zero.
Front Receiver
Your vehicle is equipped with a front receiver.
You can use the receiver with a power winch platform
(described later in this section), receiver extension
or with other accessories.
Never use the front receiver to tow a trailer.
You can use the front receiver to tow your vehicle
behind another. SeeRecreational Vehicle Towing on
page 4-65.
4-60

Receiver Extension (If Equipped)
Use the receiver extension with the front receiver and
various light-duty accessories such as bike racks.
Notice:Do not attach accessories or cargo that
weigh more than 240 lbs. (108 kg) to the receiver
extension. You could damage the receiver extension
and/or your vehicle’s frame components.
The receiver extension was not intended for heavy-duty
use, such as trailer towing, winching or vehicle
recovery.To use the front receiver with the receiver extension, do
the following:
1. Locate the receiver extension (A) in the rear of the
vehicle where it is attached to the spare tire
mounting plate.
2. Loosen the wing nuts (B) holding the extension to
the spare tire plate and remove it.
3. The extension attaches to the front receiver exactly
as the power winch platform does. See “Power
Winch Platform” following in this section.
4. Attach the accessory you will be using to the
receiver extension.
4-61

Power Winch Platform (If Equipped)
You can use the power winch platform with an
aftermarket winch. Connect the winch to the platform
and wiring to the vehicle following the winch
manufacturer’s guidelines.
1. Slide the winch platform into the front receiver of
your vehicle. To secure it, follow the next step.
You will be using the locking pin (if equipped) stored
with the jack/tool kit. SeeChanging a Flat Tire on
page 5-79for more information on location.
2. Slide the pin down through the hole in the front
bumper and into the receiver.If you look under the
receiver, you will see the
locking portion (clip) of the
pin coming through the
bottom hole in the receiver.
3. Turn the clip so that it is
perpendicular to the
pin. Pin is shown off the
vehicle for clarity.
4-62

4. Push the clip so it
locks in place. Pin is
shown off the
vehicle for clarity.
5. With the clip locked
and the pin secure,
your setup should look
like this if you look
under the receiver. The
pin is now secure
and you will be able to
use the winch.To remove the winch platform, you must rst unlock the
clip so you can pull out the pin. To unlock the clip,
squeeze the clip and turn it so it is in line with the rest
of the pin. Remove the pin and slide the winch platform
out from the receiver.
Notice:Do not use the winch platform to winch at
a tension of more than 9,000 lbs. (4 082 kg). This
would damage your vehicle’s frame. This damage
would not be covered by your vehicle’s warranty.
4-63

If you are using a winch to pull out another vehicle,
follow the winch manufacturer’s guidelines and observe
the following to prevent damage to your vehicle:
If possible, have your vehicle anchored from the
opposite side of the winch to a solid, immovable
object.
If winching from the front, use both of the rear
recovery loops. If winching from the rear, use both
of the front recovery loops.
Put your transmission in NEUTRAL (N).
Use your regular brakes to hold your vehicle in
place and block the wheels to keep the vehicle
from moving.
Notice:Using a power winch with the transmission
in gear to pull out another vehicle may damage
the transmission. When operating a power winch,
always leave the transmission in NEUTRAL (N).
Notice:Driving your vehicle through an automatic
car wash with the winch installed, can cause
damage to your vehicle and the car wash. Always
remove the winch from your vehicle before using an
automatic car wash. SeeCleaning the Outside of
Your Vehicle on page 5-95for more information.If you are using a winch to pull out your own vehicle,
follow the winch manufacturer’s guidelines for self
recovery and observe the following to prevent damage
to your vehicle:
Do not self recover your vehicle by wrapping the
winch cable around an object (such as a pulley
block or tree) and attaching it back to your vehicle’s
recovery loops.
Always attach the winch cable directly to a solid
anchor directly in front of your vehicle to achieve
a straight line pull.
4-64