lock HUMMER H2 2006 Owners Manual

4. Open the tool bag. You will nd the following
tools needed to remove the spare tire and change
a at tire:
A. Jack Handle
B. Jack Handle Extension (Used for Rear Flats Only)
C. Wheel Wrench
D. Ratchet
Before proceeding, be sure to set the wheel blocks at
the appropriate tires as previously shown.Removing Jack B and Tools (SUT)
To remove the cover, unlock it and then pull the
cover off.
Remove the tool kit/rst aid kit to gain access to the tire
changing equipment. Jack A Tools
5-73

Once it is removed, you will see the following:
Release the jack by turning the end of the jack handle
counterclockwise.
To remove the tools, do the following:
1. Pull the bottom of the driver’s side second row seat
up to access the tools. See60/40 Split Bench Seat
on page 1-6for more information.2. Remove the strap from the seat rail. Then
carefully slide the tool bag out from under the
seat rail as shown.
Take care to not pinch the seat cables or electrical
harnesses. Jack B
5-74

3. Open the tool bag. You will nd the following tools
needed to remove the spare tire and at tire:
A. Jack Handle
B. Jack Handle
Extensions (2)
C. Wheel WrenchD. Wheel Wrench
Extension
E. Wheel BlocksBefore proceeding, be sure to set the wheel blocks at
the appropriate tires as previously shown.
To use a wheel block, lift
the wheel block as shown
to lock it into place.
Jack B Tools
5-75

5. Turn the ratchet counterclockwise to loosen the
wheel nuts.Or, turn the wheel wrench with the wheel wrench
extender (jack B) counterclockwise to loosen
the wheel nuts.
6. Remove the three wheel nuts holding the spare tire
onto the tire carrier.
7. Pull off and gently lower the spare tire to the
ground. Set it next to the at tire. Jack A Tools
Jack B Tools
5-77

Removing the Spare Tire and
Tools (SUV)
Removing the Jack (SUV)
Your vehicle is equipped with either jack A or jack B.
The jack (A or B) is stored behind the driver’s side
second row seat.
1. Fold the driver’s side second row seat down to
access the jack. See60/40 Split Bench Seat on
page 1-6for more information.
2. For jack A, turn the
wing nut
counterclockwise to
release it. Then
remove the bracket
retaining the jack.For jack B, turn the
jack handle end
counterclockwise
to release it.
3. Grasp and lift the jack out of the bracket.
Jack A
Jack B
5-78

4. Open the tool bag. You will nd the following tools
needed to remove the spare tire and at tire:
A. Jack Handle
B. Jack Handle
Extension (2)
(Used for Rear
Flats Only)C. Wheel Wrench
D. RatchetA. Jack Handle
B. Jack Handle
Extensions (2)
C. Wheel WrenchD. Wheel Wrench
Extension
E. Wheel Blocks
Jack A Tools
Jack B Tools
5-80

Before proceeding, be sure to set the wheel blocks at
the appropriate tires as previously shown. To use
the wheel blocks, do the following:
For jack A, locate the wheel blocks which are stored
behind the jack on the driver’s side of the vehicle.
For jack B, remove the
wheel blocks from the tool
bag. Then, lift the wheel
block as shown to
lock it into place.Removing the Spare Tire (SUV)
The spare tire is attached to the tire carrier. To remove
the spare tire, do the following:
1. Open the tire carrier. SeeTailgate/Spare Tire
Carrier on page 2-14for tire carrier operation.
2. Unscrew the wing nut on the back of the tire carrier. Jack B Wheel Blocks
5-81

3. Pull off the license plate holder from the spare tire.
4. For jack A, slide the ratchet onto the wheel
wrench with the DOWN mark facing you. For jack B,
attach the wheel wrench to the wheel wrench
extender to remove the wheel nuts.5. Turn the ratchet with the wheel wrench (jack A)
counterclockwise to loosen the wheel nuts.
Jack A Tools
5-82

Or, turn the wheel wrench with the wheel wrench
extender (jack B) counterclockwise to loosen
the wheel nuts.
6. Remove the three wheel nuts holding the spare tire
onto the tire carrier.
7. Pull off and gently lower the spare tire to the
ground. Set it next to the at tire.
Removing the Flat Tire and
Installing the Spare Tire (SUT
and SUV)
Jack A (SUV and SUT)
1. To remove the center
cap, place the at end
of the wheel wrench
in the slot on the wheel
and carefully pry the
center cap out.
Jack B Tools
5-83

2. Slide the ratchet onto the wheel wrench with the
DOWN mark facing you.
3. Turn the ratchet counterclockwise to loosen the
wheel nuts. Do not remove them yet.
You will now need to jack the vehicle up using the
following instructions.4. Assemble the jack and tools as follows:
Front Flat Tire:Attach the jack handle with the
hook end connected to the u-hook/clevis on
the jack. Slide the ratchet onto the jack handle with
the UP mark facing you.
Rear Flat Tire:Assemble the jack together with the
jack handle and the jack handle extension. Press
with the UP mark facing you. The retention clip
on the jack handle extension (arrow) so it engages
into the jack handle. Slide the ratchet onto the
jack handle extension.
5. Turn the ratchet clockwise to raise the jack head to
the lifting point.
5-84