wheel Hyundai Accent 2006 Manual PDF

3 IN CASE OF EMERGENCY
12
D080B01A
VEHICLE TOWING OR RECOVERY
D080A01A
o OK FOR AUTOMATIC OR MANUAL
TRANSAXLE EQUIPPED VEHICLE WITH NO DAMAGE
BD090A1-E Manual Transxle Vehicle The vehicle may be towed by the con- ventional method using the towing eye at the front of the vehicle as an attach- ment point. In addition, a suspendedtow with or without a towing dolly may be used with either the front or the rear wheels being suspended, provided theabove caution is observed.
SD080A1-E
CAUTION:
An incorrect tow or recovery couldresult in serious damage to the ve- hicle. If any damage to the suspen- sion, steering or transaxle is appar-ent or suspected, a towing dolly must be used. o OK FOR AUTOMATIC OR MANUAL
TRANSAXLE EQUIPPED VEHICLE
!
Ensure that the spare wheel, jack and wheel nut wrench as well tools arecorrectly located in the boot of the vehicle to prevent damage and noise.

3
IN CASE OF EMERGENCY
13
D080C02A
D080C01A
SD100A2-E Automatic Transaxle Vehicle The vehicle may be towed by the con- ventional method using the towing eyeat the front of the vehicle as an attach- ment point. In addition, a suspended tow may begiven to the front of the vehicle without a towing dolly. In the event of a sus- pended tow being given to the rear ofthe vehicle, the use of a towing dolly is imperative. o NOT OK FOR AUTOMATIC
TRANSAXLE EQUIPPED VEHICLE
o OK FOR MANUAL TRANSAXLE
In addition, the following points must be noted:
o If towing by conventional means,
the ignition key must be at the "ACC" position, otherwise the steering lock will be activated.
o Because the brake system and
steering system power assis-tance is derived from the engine, the amount of effort required tostop or steer the vehicle will be greater than normal.
o If a suspended tow is being given to the rear, the ignition key mustbe at the "ACC" position since the steering lock is not designedto withstand the force required to hold the front wheels straight during the tow.
o The vehicle must not be towed with the front wheels on theground for more than thirty miles.
! CAUTION:
The following restriction must be observed in order to avoid serious damage to the transaxle . The vehicle must never be towedfrom the rear with the front wheels on the ground. The vehicle must not be towed untiltransaxle fluid has been added to bring the level up to the "HOT" marking on the dipstick. (The levelwill need to be reduced again after towing).
o OK FOR AUTOMATIC OR MANUAL
TRANSAXLE EQUIPPED VEHICLE

3 IN CASE OF EMERGENCY
14IF YOU LOSE YOUR KEYS
D120A01A-EAT Information about the key of immobiliser system will be found on page 1-4.
The vehicle must not be towed atspeeds faster than 25 mph. or dis- tances greater than fifty miles. Thegeneral points regarding the steer- ing lock etc. described in the pre- ceding section (Manual transaxlevehicle) should be observed.
D080D03A-EAT EMERGENCY TOWING For emergency towing when no com- mercial tow vehicle is available, attach a tow cable, chain or strap to one of the towing hooks under the front/rear ofyour car. Do not attempt to tow your vehicle in this manner on any unpaved HLC4014surface. This may result in serious damage to your car.Nor should it be attempted if the wheels, drive train, axles, steering or brakes are damaged. Before towing, be surethe transaxle is in neutral and the key in "ACC" (with the engine off) or in the "ON" position (with the engine run-ning). A driver must be in the towed car to steer it and operate the brakes.
CAUTION:
If the car is being towed with all fourwheels on the ground, it can be towed only from the front. Be surethat the transaxle is in neutral. Do not tow at speeds greater than 25 mph(50 km/h) and for more than 15miles (25 km). Be sure the steering is unlocked by placing the key in the "ACC" posi-tion. A driver must be in the towed vehicle to operate the steering and brakes.
!
Front
Rear

44APPEARANCE CARE
2
SE020A1-E By using the most advanced design and construction practices, every Hyundai is built to retain the original factory finish for many years. How-ever, long term durability is also greatly dependant upon maintaining the vari- ous protection systems and coatingsused in manufacture since constant, exposure to the elements will result in a breakdown and loss of effective-ness. The following suggestions are made to assist in the maintenance of the vehicle bodywork. SE030A1-E UNDERBODY COATINGS Every Hyundai passenger car receives a full underbody and cavity injectiontreatment during production. In order that this treatment may retain maxi- mum effectiveness it is recommendedthat the underbody receives a power wash and a thorough inspection after each winter season. In doing so anyaccumulations of mud, which act as moisture traps and combine with road salts to accelerate corrosion will beremoved. In order to maintain the Anti Perforation Warranty, the requirements regarding the retreatment programmemust be observed in accordance with the Terms and Conditions outlined in the separate Anti Perforation WarrantyBooklet. NOTE: The underbody should never be steam cleaned since the underbody coating may be removed by thisprocess. During the interim period between power washing the underbody, themore vulnerable areas such as wheel arches should be hosed off particularly during the winter sea-son to prevent prolonged contact with road salts. Ensure that the various drain pointslocated at the bottom of the door panels and sills are kept clear to prevent water from becomingtrapped within the cavities. Wher- ever possible, the parking of the vehicle in a confined, poorly venti-lated location (a garage for example) should be avoided when the ve- hicle is wet or is covered with snowor ice. Under these conditions, the internal cavities of the vehicle will remain damp for prolonged peri-ods of time which will encourage corrosion. Parking the vehicle where good ventilation exists (out-side for example) is preferable.
PROTECTING YOUR HYUNDAI FROM CORROSION

4
CORROSION PREVENTION AND APPEARANCE CARE
3
4
APPEARANCE CARE
3
SE040A1-E Regular cleaning of the exterior paintwork serves two important func- tions. Firstly, the removal of abrasive dirt and contaminants will maintain thelustre of the paintwork and will prevent discolouration and dulling due to pro- longed contact.Secondly, the presence of damage through impact or abrasion will be ap- parent allowing early rectification to bemade thus preventing corrosion from becoming established and spreading beneath the paint film. To avoid "waterspotting" the vehicle should not be washed in direct sunlight particularly in the case of vehicles having dark bodycolours. The heat from the sun rays is absorbed by the paint film increasing the surface temperature. This actioncauses water used for washing to evaporate quickly leaving behind the deposits from the water and the sham-poo used. Use only a shampoo intended for the purpose and ensure that the body workis thoroughly wetted to soften the dirt film prior to attempting to remove this. After removing the dirt film with a soft sponge, the body work should be thor-oughly rinsed and then dried with agood quality chamois leather to pre- vent streaking or spotting of the paint work.Household detergents, solvents and abrasive cleaning materials should not be used in order to avoid damaging thepaint film. Plastic wheel covers should be cleaned using a sponge and water. Cast alloywheels should be cleaned using a mild soap or neutral detergent. Abrasive compounds must not be used since inthe event of these damaging the lac- quer coating, oxidization of the alu- minium wheel will occur, spoiling theappearance. The use of an a toothbrush will facili- tate cleaning between the wheel"spokes".
VALETING
SE050A1-E INTERIOR During the winter period, it is possible that the passenger compartment floor-ing may become wet from damp foot- wear or quantities of snow adhering to footwear. The carpet should not beallowed to remain in this condition since the carpet may begin to create musty smells and will promote corrosion ofthe floor pan in addition to the carpet and under felt beginning to rot.

5
VEHICLE MAINTENANCE REQUIREMENTS
5
F030C02TB-EAT R : Replace I : Inspect and, after inspection, clean, adjust, repair or replace if necessary
GENERAL MAINTENANCE COOLING SYSTEMCOOLANTCOOLANT SPECIFIC GRAVITYMANUAL TRANSAXLE OILAUTOMATIC TRANSAXLE FLUID BRAKE PIPES, HOSES, AND CONNECTIONS BRAKE FLUIDCLUTCH FLUIDREAR BRAKE LININGS AND CYLINDERSBRAKE PADS SUSPENSION AND STEERING SYSTEM FRONT SUSPENSION BALL JOINTSPOLLEN FILTER (FOR EVAPORATOR AND BLOWER UNIT)REAR WHEEL BEARINGSTYRE CONDITION AND PRESSURE (incl. Spare)LUBRICATE LOCKS AND HINGES CHECK ALL ELECTRICAL SYSTEMS ROAD TESTCHECK ALL SYSTEMS WITH HI-SCAN 60 72
50 60
4048
I I I
R I
R R I I II
R II I III
I I IIIII I II
R I I IIII
I I III
RR IIII
R I I IIII
30 36
I I IIIII I II
R I I IIII
I I III
RR IIII
R I I IIII
10 12
I I IIIII I II
R I I IIII
MILES X 1000 MONTHS
NO. DESCRIPTION
1 2345 6 789
10 11 1213141516 17 1819
See Note (1)
Note : (1) FOR THE FIRST TIME, REPLACE THE COOLANT 60,000 MILES OR 60 MONTHS. AFTER THAT, REPLACE IT EVERY 30,000 MILES OR 24 MONTHS.
20 24

5VEHICLE MAINTENANCE REQUIREMENTS
10
6ZF070P1-A
o Driveshafts and boots
Check the drive shafts, boots and clamps for cracks, deterioration, or damage. Replace any damaged parts and, if necessary, repack the grease. 6ZF070Q1-A
o Air conditioning refrigerant
Check the air conditioning lines and connections for leakage and damage.Check air conditioning performance according to the relevant shop manual if necessary.
6ZF070M1-A o Steering gear box, linkage &
boots/lower arm ball joint
With the vehicle stopped and engine off, check for excessive freeplay in the steering wheel. Check the linkage for bends or dam- age. Check the dust boots and ball joints for deterioration, cracks, or dam- age. Replace any damaged parts. 6ZF070N1-A
o Power steering pump, belt and hoses
Check the power steering pump and hoses for leakage and damage. Re-place any damaged or leaking parts immediately. Inspect the power steer- ing belt for evidence of cuts, cracks,excessive wear, oiliness and proper tension. Replace or adjust it if neces- sary.

6OWNER MAINTENANCE
22
G160A01EHLC5008
CHECKING THE FREEPLAY
SG160A1-E CLUTCH PEDAL The clutch pedal freeplay should be checked against the specified value. Ifthe freeplay is not correct, the clutch should be adjusted by a Hyundai dealer. 0.24 ~ 0.51 in. (6 ~ 13 mm)
!
4. Replace the two filters.
5. Installation is the reverse order of
disassembly.
CAUTION:
Be sure to install the pollen filter in the direction of the arrow sign. Un-less, it may cause noise or deteriora- tion. HLC2099-D
SG150A1-E STEERING WHEEL Steering wheel freeplay should be checked to ensure that the specifiedvalue is not exceeded.
1.18 in. (30 mm)

Vehicle Identification Number (VIN) .............................. 8-2
Engine Number ............................................................. 8-2
Tyre Information ............................................................ 8-3
Tyre Pressures ............................................................. 8-3
Snow Tyres .................................................................. 8-3
Tyre Chains .................................................................. 8-4
Tyre Rotation ................................................................ 8-4
Tyre Balancing .............................................................. 8-4
Tyre Replacement ........................................................ 8-5
Wheel Replacement ..................................................... 8-5
Spare Tyre and Tools ................................................... 8-5
8
CONSUMER INFORMATION
8

8CONSUMER INFORMATION
4
I060A02A-EAT TYRE ROTATION Tyre wear will vary for each wheel. In order to increase the life of each tyre and keep wear uniform, tyre rotationshould be performed every 10,000 miles as shown in figure. NOTE:
o Do not include a steel wheel sparetyre when rotating aluminum al- loy wheel tyres.
o Do not mix bias-ply and radial-ply under any circumstances. Thismay cause dangerous handling characteristics. SI060A1-E TYRE BALANCING Incorrect tyre balance will cause steer- ing vibration and uneven tyre wear. Thevehicle tyres are balanced during pro- duction but may need further balancing throughout the life of the tyres.It is recommended that the tyres be balanced on the car for best results and that the tyres are balanced wheneverthey have been removed from the wheel for repair.
!
I050A01TB-EAT TYRE CHAINS Tyre chains, if necessary, should be installed on the front wheels. Be surethat the chains are installed in accor- dance with the manufacturer's instruc- tions.To minimize tyre and chain wear, do not continue to use tyre chains when they are no longer needed.
WARNING:
o When driving on roads covered with snow or ice, drive at lessthan 20 mph (30 km/h).
o Use the SAE "S" class or wire &
plastic chains.
o Don't use the tyre chains in 185/ 55R 15 tyre to prevent body dam-age.
o If you have noise caused by chains contacting the body, retighten thechain to avoid contact with thevehicle body.
o To prevent body damage, retighten
the chains after driving 0.3~0.6miles (0.5~1 km).
HA1409Spare tyre