high beam Hyundai Coupe 2003 User Guide

CONTROLS AND EQUIPMENT1- 27
SB210K1-E
OIL PRESSURE WARNING LAMP
CAUTION: If the oil pressure lamp illuminates when the engine is running, an insufficient oil pressurelevel for continued safe operation of the en-gine exists. Continued operation of the en-gine in this condition may result in seriousengine damage. Under normal circumstances, the lamp will illu- minate when the ignition is turned "on" and will beextinguished when the engine is started.If the oil pressure warning lamp illuminates whilstthe engine is running, stop the engine immedi-ately and check the engine oil level. If the level isinsufficient, add the required amount of oil asindicated by the engine oil dipstick. If the lampfails to extinguish when the engine is restarted,do not continue to operate the vehicle.If the oil pressure lamp illuminates during normaloperation and the cause is not an insufficient oillevel, or the lamp fails to illuminate when theignition is turned "on", contact the nearest Hyundaidealer before further operating the vehicle.
SB210G1-E TURN SIGNAL INDICATOR LAMPS
Operation of a turn signal is indicated by the warning lamp located in the instrument cluster. Ifthe lamp fails to illuminate or does not flash, amalfunction within the turn signal system is indi-cated.
SB210J1-E HIGH BEAM INDICATOR LAMP
The high beam indicator lamp will illuminate whenever the headlamps are switched to highbeam of flash position.
260P02Y-EAT
ABS SERVICE REMINDER IN- DICATOR (Not all models)
When the key is turned to the "ON" position, the Anti-Lock Brake System SRI will come on andthen go off in a few seconds. If the ABS SRIremains on, comes on while driving, or does notcome on when the key is turned to the "ON"position, this indicates that there may be a prob-lem with the ABS.If this occurs, have your vehicle checked by yourHyundai dealer as soon as possible. The normalbraking system will still be operational, but with-out the assistance of the anti-lock brake system. WARNING:If the both ABS SRI and Parking Brake/Brakefluid level warning lights remain "ON" orcome on while driving, there may be a prob-lem with E.B.D (Electronic brake force distri-bution).If this occurs, avoid sudden stops and haveyour vehicle checked by your Hyundai dealeras soon as possible.
B260B01GK-GAT
SRS (AIRBAG) SERVICE REMINDER INDICATOR (SRI)
The SRS service reminder indicator (SRI) comes on and flashes for about 6 seconds after theignition key is turned to the "ON" position or afterthe engine is started, after which it will go out. This light also comes on when the SRS is not working properly. If the SRI does not come on orilluminates continuously when the ignition key isturned to "ON", or continuously remains on afterflashing for about 6 seconds when you turned theignition key to the "ON" position or started theengine, or if it comes on while driving, have theSRS inspected by an authorized Hyundai Dealer.

CONTROLS AND EQUIPMENT
1- 34 SB220D1-E HIGH AND LOW BEAM To turn on the headlight high beams, push the lever forward (away from you). For low beams,pull the lever back (toward you). The appropriateheadlight beam indicator light will come on at thesame time.
SB220E1-E HEADLIGHT FLASH
SB220C3-ELIGHTING SWITCH The vehicle sidelamps and headlamps are oper- ated by rotating the end of the turn signal switchbarrel. To operate the sidelight, rotating the switchto the first detent with ignition switch at the "OFF"position will cause the lamps to illuminate. Tooperate the headlamps, the turn signal switchbarrel should be rotated to the second detent.The headlamps will only operate when the igni-tion switch is at the "On" position. If the ignitionswitch is turned to the "Off" position, only thesidelight will function. The headlight may be flashed by pulling the turnsignal switch lever towards the steering wheel.The headlight will be extinguished when theswitch is released.
To indicate an intention to change lanes, movingthe lever slightly towards the direction of therelevant turn signal will cause the turn signallamps to flash. When the lever is released, it willreturn to the "off" position.
HGK039-D
To operate the automatic light feature, turn the barrel on the end of the multi-function switch. Ifyou set the multi-function switch to "AUTO", thetail lights and headlights will be turned automati-cally on or off according to external illumination.
B340G01L-GAT Auto Light (Not all models)
HGK041-D
HGK233-D
NOTE: The ignition must be in the "ON" position toturn on the headlights. Parking light auto cut If you do not turn the parking lights "OFF" afterdriving, the parking lights will automatically shut"OFF" when the driver's door is opened.To turn them "ON" again you must simply turn theignition key to the "ON" position.

CONTROLS AND EQUIPMENT
1- 38
SB320A2-F HEADLIGHT LEVELING DEVICE SYS- TEM
HGK157-D
To adjust the headlight beam level according to the number of the passengers and the loadingweight in the luggage area, turn the beam level-ing switch.The higher the number of the switch position, thelower the headlight beam level.Always keep the headlight beam at the properleveling position, or headlights may dazzle otherroad users.Listed below are the examples of recommendedswitch settings.For loading conditions other than those listedbelow, adjust the switch position so that thebeam level may be the nearest as the conditionobtained according to the list.
B450A01GK-GAT DRINK HOLDER (Not all models)
HGK149-D
The drink holder is used for holding cups or cans. To use the passenger's drink holder, push thedrink holder. WARNING: Do not place objects other than cups or cansin the drink holder. Such objects can bethrown out in the event of a sudden stop or anaccident, possibly injuring the passengers inthe vehicle. Driver's
Passenger's
B430A01GK-AAT FRONT ASHTRAY The front ashtray may be opened by pushing and releasing the ashtray door at its top edge. To remove the ashtray in order to clean it, the metal ash receptacle should be lifted out from theashtray door. Do not attempt to remove the entireashtray door assembly or damage will result. Toreinstall it, place it in the proper position andpress it down in the ashtray door. The ashtraylamp will only illuminate when the exterior bodylights are switched on.HGK146-D

OWNER MAINTENANCE
6-18 NOTE: Grinding noise from power steering pumpmay be heard immediately after the engine isstarted in extremely cold condition (below-20°C). In this case, if the noise stops duringwarm up, there is no abnormal function in thesystem. This is due to a power steering fluidcharacteristic in extremely cold conditions. FLUID RECOMMENDATION
Only automatic transaxle fluid meeting the speci-
fication of PSF-3 or Dexron 2 oil should be used in the power steering system.
SG230A1-E POWER STEERING FLUID LEVEL The power steering fluid level should be checked daily.To check the power steering fluid level, be surethe ignition is "OFF", then check to make certainthat the power steering fluid level is between the"MAX" and "MIN" level markings on the fluidreservoir.
SG250A2-E REPLACING HEADLIGHT BULBSIn the event of bulb failure being experienced, ensure that the relative lighting circuit is turnedoff prior to attempting to replace the bulb. Theillustrations on the following pharagraph will as-sist in locating and removing the headlight bulbs.Ensure that the replacement bulb has the samecap configuration and wattage as the original.
SG230B1-E POWER STEERING HOSESPower steering hoses should be checked for damage, deterioration and leakage at each ser-vice.
The engine cooling fan should operate before thetemperature gauge reaches the upper portion ofthe scale and the condenser fan should operatewhenever the air conditioning is in use.
HGK214 G270A02A-GAT HEADLIGHT BULB Replacement instructions:
HGK225
1. Allow the bulb to cool. Wear eye protection.
2. Always grasp the bulb by its plastic base, avoid touching the glass.
3. Disconnect the power cord from the bulb base in the back of the headlight.
4. Remove the dust cover.
5. Push the bulb spring for removing the head- light bulb.
6. Remove the protective cap from the replace- ment bulb and install the new bulb by match-ing the plastic base with the headlight hole.Install the dust cover after retightening thebulb spring and reconnect the power cord.
7. Use the protective cap and carton to dispose of the old bulb.
8. Check for proper headlight aim.High Beam Low Beam
Turn signal Light

OWNER MAINTENANCE 6-19
G290A01GK-EAT HEADLIGHT AIMING ADJUSTMENT
Before performing aiming adjustment, make sure of the following.
1. Keep all tyres inflated to the correct pressure.
2. Place the vehicle on level ground and press
the front bumper & rear bumper down severaltimes. Place vehicle at a distance of 118.1 in.(3m) from the test wall.
3. See that the vehicle is unloaded (except for full levels of coolant, engine oil and fuel, andspare tyres, jack, and tools).
4. Clean the head lights lens and turn on the headlight.
5. Open the bonnet.
6. Draw the vertical line (through the centre of each headlight beam pattern) and the hori-zontal line (through the centre of each head-light beam pattern) on the aiming screen.And then, draw a parallel line at 1.18 in. (30mm) under the horizontal line.
WARNING:The halogen bulb contains gas under pres-sure and if impacted could shatter, resultingin flying fragments. Always wear eye protec-tion when servicing the bulb. Protect the bulbagainst abrasions or scratches and againstliquids when lighted. Turn on the bulb onlywhen installed in a headlight. Replace theheadlight if damaged or cracked. Keep thebulb out of the reach of children and disposeof the used bulb with care.
Vertical aiming
G290A01GK
Horizontal aiming
Low Beam
Vertical aiming
G290A02GK
Horizontal aiming
High Beam
7. Adjust each cut-off line of the low beam to the
parallel line with a phillips screwdriver - VER- TICAL AIMING.
8. Adjust each cut-off line of the low beam to the each vertical line with a phillips screwdriver -HORIZONTAL AIMING.
G290B01GK-EAT Adjustment After Headlight Assembly Replacement
G290B02Y
Vertical line
Cut-off line Ground line
Horizontal line
LW
H
H "P"1.18 in.(30 mm)
If the vehicle has had front body repair and the headlight assembly has been replaced, the head-light aiming should be checked using an aimingscreen as shown in the illustration. Turn on theheadlight switch.
1. Adjust headlights so that main axis of light is parallel to centre line of the body and isaligned with point "P" shown in the illustration.
2. Dotted lines in the illustration show centre of headlights.

OWNER MAINTENANCE
6-20
SPECIFICATION: "H"Horizontal centre line of headlights from ground:Low Beam: 26.7 in. (679mm)High Beam: 26.5 in. (672mm) "W" Distance between each headlight centre : LowBeam: 47.3 in. (1,202mm)High Beam: 38.0 in. (966mm) "L" Distance between the headlights and the wallthat the lights are tested against : 118.11 in.(3,000 mm)