ECO mode Hyundai Coupe 2003 Owner's Guide

CONTROLS AND EQUIPMENT
1- 12
SB090H1-E CARE OF SEAT BELTSSeat belt assemblies must never be disassembled or modified in any way. In addition, care shouldbe exercised to ensure that the belt assembliesdo not become damaged by being trapped in seatmechanisms, door shuts etc. SB090I-E Periodic Inspection It is recommended that all seat belts be inspected periodically for wear or damage of any kind.Parts of the system that are damaged should bereplaced as soon as possible. Under no circum-stances must any part of the seat belt assem-blies be dismantled or repaired. SB090J1-E Keep Belts Clean and Dry Seat belts should be kept clean and dry. If belts become dirty, they can be cleaned using a mildsoap solution and warm water. Bleach, dye,strong detergents or abrasives should not beused since the fabric may become damaged andweakened.
SB090K1-E Replacement of Seat BeltsThe entire seat belt assembly or assemblies should be replaced if the vehicle has been in-volved in an accident even if no damage isevident. Additional questions concerning seatbelt operation should be directed to a HyundaiDealer. SB090O1-F FRONT SEATBELT PIVOT HEIGHT AD- JUSTMENT (Not all models)
attempt to adjust the height of the upper anchor- age point while the vehicle is moving.If you are any doubt as to the method of adjust-ment or the optimum height position for your frontseat belt always contact your nearest HyundaiDealer. WARNING:
o The height adjuster must be in the locked
position when the vehicle is moving.
o The misadjustment of height of the shoul- der belt could reduce the effectiveness ofthe seat belt in a crash.
HGK109
The location of the upper anchorage point can be set (for greater belt comfort and security) to anyone of five preset positions. To adjust the seatbelt pivot push the knob upward or downward tothe required setting, ensuring that it engages oneof the preset positions (on releasing the knob).The height adjuster must always be locked intoposition while the vehicle is stationary. Do not

CONTROLS AND EQUIPMENT
1- 18 B180B01GK-GAT Pre-tensioner Seat Belt (Not all models)Your Hyundai vehicle is equipped with driver's and front passenger's pre-tensioner seat belts.The purpose of the pre-tensioner is to make surethat the seat belts fit tightly against the occu-pant's body in certain frontal collisions.The pre-tensioner seat belts can be activatedalone or, where the frontal collision is severeenough, together with the airbags. When the vehicle stops suddenly, or if the occu- pant tries to lean forward too quickly, the seat beltretractor will lock into position. In certain frontal
B180B01S-D
B230H03GK-EAT Child Seat Restraint Suitability For Seat Position Use child safety seats that have been officially approved and are appropriate for your children.
Age Group
Seating Position
0 : Up to 10 kg (0 ~ 9 months)0+ : Up to 13 kg(0 ~ 2 years)I : 9kg to 18kg(9 months ~4 years)II & III : 15kg to 36kg(4 ~ 12 years)
U : Suitable for "universal" category restraints
approved for use in this mass group
UF : Suitable for forward-facing "universal" cat- egory restraints approved for use in this mass group
L1 : Suitable for "Römer ISOFIX GR1" approved for use in this mass group(Approval No: E1 R44-03301133)
X : Seat position not suitable for children in this mass group
N/A : No seating position is provided The seat belt pre-tensioner system consistsmainly of the following components. Their locations are shown in the illustration.
1. SRS airbag warning light
2. Seat belt pre-tensioner assembly
3. SRS control module WARNING: To obtain maximum benefit from a pre-tensioner seat belt:
1. The seat belt must be worn correctly.
2. The seat belt must be adjusted to the
correct position.
B180B01GK-D
Driver's side airbag
1
2
3Passenger's side airbag
N/A N/A N/A N/A
Rear
Center
Rear
Outboard
X X
L1 X
1st
Passenger
XX X X NOTE: This vehicle is equipped with thether anchor-age and ISOFIX system to supply most suit-able safety. we recommend to buy a childrestraint system to use thether anchorageand ISOFIX system.
collisions, the pre-tensioner will activate and pullthe seat belt into tighter contact against theoccupant's body.

CONTROLS AND EQUIPMENT1- 19
B240A01GK
Driver's Airbag
B240A01GK-GAT SUPPLEMENTAL RESTRAINT (AIRBAG) SYSTEM (SRS)(Not all models) Your Hyundai is equipped with a Supplemental Restraint (Airbag) System. The indications of thesystem's presence are the letters "SRS AIRBAG" embossed on the ornament in the steeringwheel and the passenger's side front panel padabove the glove box. The Hyundai SRS consists of airbags installed under the pad covers in the center of the steeringwheel and the passenger's side front panel abovethe glove box. The purpose of the SRS is toprovide the vehicle's driver and/or the front pas-senger with additional protection than that of-fered by the seat belt system alone, in case of afrontal impact of sufficient severity.
NOTE:
o Both the driver's and front passenger's
pre-tensioner seat belts will be activatedin certain frontal collisions. The pre-tensioner seat belts can be activated aloneor, where the frontal collision is severeenough, together with the airbags.
o When the pre-tensioner seat belts are ac- tivated, a loud noise may be heard and finedust, which may appear to be smoke, maybe visible in the passenger compartment.These are normal operating conditionsand are not hazardous.
o Although it is harmless, the fine dust may cause skin irritation and should not bebreathed for prolonged periods. Wash yourhands and face thoroughly after an acci-dent in which the pre-tensioner seat beltswere activated.
CAUTION:
o The control module that activates the SRS airbag controls the pre-tensioner seat beltalso.
o If there is some function in the pre- tensioner seat belt circuit, the warninglight will illuminate even if there is nomalfunction in the SRS airbag system. Ifthe SRS airbag warning light does notilluminate or illuminates continuouslywhen the ignition key is turned to "ON", orif it remains illuminated after blinking forapproximately 6 seconds, or if it illumi-nates while the vehicle is being driven, please have an authorized Hyundai dealerinspect the pre-tensioner seat belts and orSRS airbag system as soon as possible.
WARNING:
o Pre-tensioners are designed to operate only one time. After activation, pre-tensioner seat belts must be replaced. Allseat belts, of any type, should always bereplaced after they have been worn duringa collision.
o The pre-tensioner seat belt assembly mechanisms become hot during activa-tion. Do not touch the pre-tensioner seatbelt assemblies for several minutes afterthey have been activated.
o Do not attempt to inspect or replace the pre-tensioner seat belts yourself. Thismust be done by an authorized Hyundaidealer.
o Do not strike the pre-tensioner seat belt assemblies.
o Do not attempt to service or repair the pre- tensioner seat belt system in any manner.
o Improper handling of the pre-tensioner seat belt assemblies, and failure to heedthe warnings to not strike, modify, in-spect, replace, service or repair the pre-tensioner seat belt assemblies may leadto improper operation or inadvertent acti-vation and serious injury.
o Always wear seat belts when driving or riding in a motor vehicle.

CONTROLS AND EQUIPMENT
1- 22
WARNING:
o When the SRS is activated, there may be a loud noise and fine dust will be releasedthroughout the vehicle. These conditionsare normal and are not hazardous. How-ever, the fine dust generated during airbagdeployment may cause skin irritation.Wash your hands and face thoroughlywith lukewarm water and a mild soap afteran accident in which the airbags weredeployed.
o The SRS can function only when the igni- tion key is in the "ON" position. If the SRSSRI does not come on or illuminatescontinuously when the ignition key isturned to "ON", or continuously remainson after flashing for about 6 seconds whenthe ignition key is turned to the "ON"position, or after the engine is started,comes on while driving, the SRS is notworking properly. If this occurs, have yourvehicle immediately inspected by yourHyundai dealer.
o Before you replace a fuse or disconnect a battery terminal, turn the ignition key tothe "LOCK" position or remove the igni-tion key. Never remove or replace the airbag related fuse(s) when the ignition keyis in the "ON" position. Failure to heed thiswarning will cause the SRS SRI to illumi-nate.
FUD1115A
CAUTION: When installing a container of liquid air fresh-ener inside a vehicle, do not place it near theinstrument cluster nor on the instrument panelpad surface. If there is any leakage from theair freshener onto these areas (instrumentcluster, instrument panel pad or air ventila-tor), it may damage these parts. If the liquidfrom the air freshener does leak onto theseareas, wash them with water immediately. Your Hyundai is equipped with a side airbag ineach front seat. The purpose of the airbag is toprovide the vehicle's driver and/or the front pas-senger with additional protection than that of-fered by the seatbelt alone. The side impactairbags are designed to deploy only during cer-tain side-impact collisions, depending on thecrash severity, angle, speed and point of impact.The air bags are not designed to deploy in all sideimpact situations. WARNING:
o The side impact airbag is supplemental to
the driver's and the passenger's seat beltsystems and is not a substitute for them.Therefore your seat belts must be worn atall times while the vehicle is in motion. Theairbags deploy only in certain side impactconditions severe enough to cause sig-nificant injury to the vehicle occupants.
B990B04Y-AAT Side Airbag (Not all models)
B990B01L.DAG

CONTROLS AND EQUIPMENT1- 27
SB210K1-E
OIL PRESSURE WARNING LAMP
CAUTION: If the oil pressure lamp illuminates when the engine is running, an insufficient oil pressurelevel for continued safe operation of the en-gine exists. Continued operation of the en-gine in this condition may result in seriousengine damage. Under normal circumstances, the lamp will illu- minate when the ignition is turned "on" and will beextinguished when the engine is started.If the oil pressure warning lamp illuminates whilstthe engine is running, stop the engine immedi-ately and check the engine oil level. If the level isinsufficient, add the required amount of oil asindicated by the engine oil dipstick. If the lampfails to extinguish when the engine is restarted,do not continue to operate the vehicle.If the oil pressure lamp illuminates during normaloperation and the cause is not an insufficient oillevel, or the lamp fails to illuminate when theignition is turned "on", contact the nearest Hyundaidealer before further operating the vehicle.
SB210G1-E TURN SIGNAL INDICATOR LAMPS
Operation of a turn signal is indicated by the warning lamp located in the instrument cluster. Ifthe lamp fails to illuminate or does not flash, amalfunction within the turn signal system is indi-cated.
SB210J1-E HIGH BEAM INDICATOR LAMP
The high beam indicator lamp will illuminate whenever the headlamps are switched to highbeam of flash position.
260P02Y-EAT
ABS SERVICE REMINDER IN- DICATOR (Not all models)
When the key is turned to the "ON" position, the Anti-Lock Brake System SRI will come on andthen go off in a few seconds. If the ABS SRIremains on, comes on while driving, or does notcome on when the key is turned to the "ON"position, this indicates that there may be a prob-lem with the ABS.If this occurs, have your vehicle checked by yourHyundai dealer as soon as possible. The normalbraking system will still be operational, but with-out the assistance of the anti-lock brake system. WARNING:If the both ABS SRI and Parking Brake/Brakefluid level warning lights remain "ON" orcome on while driving, there may be a prob-lem with E.B.D (Electronic brake force distri-bution).If this occurs, avoid sudden stops and haveyour vehicle checked by your Hyundai dealeras soon as possible.
B260B01GK-GAT
SRS (AIRBAG) SERVICE REMINDER INDICATOR (SRI)
The SRS service reminder indicator (SRI) comes on and flashes for about 6 seconds after theignition key is turned to the "ON" position or afterthe engine is started, after which it will go out. This light also comes on when the SRS is not working properly. If the SRI does not come on orilluminates continuously when the ignition key isturned to "ON", or continuously remains on afterflashing for about 6 seconds when you turned theignition key to the "ON" position or started theengine, or if it comes on while driving, have theSRS inspected by an authorized Hyundai Dealer.

CONTROLS AND EQUIPMENT1- 29
SB210S1-E BRAKE PAD WEAR INDICATORThe front brake disc pads are fitted with an audible wear indicator which will cause a highpitched noise to be emitted when the remainingamount of friction lining is below the specifiedvalue. When the wear indicator is heard, thebrake pads should be replaced without delay toavoid damage occurring to the brake discs and asevere reduction in braking efficiency. SB215A1-E FUEL GAUGE The fuel gauge indicates the quantity of fuel remaining in the fuel tank. NOTE: The fuel gauge is not intended to give otherthan an approximate indication of the fuellevel and is unsuitable for the purposes ofcalculating fuel consumption figures.
B260N01GK-EAT
MALFUNCTION INDICATOR LAMP
This lamp illuminates when there is a malfunction of an exhaust gas related component, and the
system is not functioning properly so that theexhaust gas regulation values are not satisfied.This lamp will also illuminate when the ignition
key is turned to the "ON" position, and will go outafter engine starting. If it illuminates while driving,or does not illuminate when the ignition key isturned to the "ON" position, take your car to yournearest authorized Hyundai dealer and have thesystem checked.
shortage may occur. This situation must be avoided to prevent damage to the catalyst occur-ring. B260E01HP-GAT
SEAT BELT WARNING LIGHT (Not all models)
The seat belt warning light blinks for about 6 seconds when the ignition key is turned from the"OFF" position to "ON" or "START".
B260Q01E-GAT
CRUISE INDICATOR (Not all models)
The cruise indicator light in the instrument cluster is illuminated when the cruise control main switchon the end of the barrel is pushed.The indicator light does not illuminate when thecruise control main switch is pushed a secondtime.Information about the use of cruise control isbeginning on page 1-48.
HGK133
B265C01O-AAT Traction Control Indicator Lights (If installed)
The traction control indicators change operation according to the ignition switch position andwhether the system is in operation or not.They will illuminate when the ignition key isturned to the "ON" position, but should go outafter three seconds. If the TCS or TCS-OFFindicator stays on, take your car to your autho-rized Hyundai dealer and have the systemchecked. See section 2 for more informationabout the TCS.

CONTROLS AND EQUIPMENT1- 31
The trip computer is a microcomputer-controlled driver information system that displays informa-tion related to driving, such as distance to empty,average speed and drive time on the LCD. RESET SWITCH
o The reset switch is used to zero the multi-
functional display mode.
o Pushing in the reset switch on the left side of tacometer changes the display as follows;
HGK095B
B400B01GK-EAT TRIP COMPUTER
A Type
B Type
1. OdometerThe odometer records the total driving distance in miles, and is useful for keeping a record formaintenance intervals. NOTE: Any alteration of the odometer may void yourwarranty coverage. 2,3 Trip odometer Records the distance of 2 trips in miles. TRIP A:
First distance you have traveled from
your origination point to a first destination.TRIP B: Second distance from the first destina-
tion to the final destination. To shift from TRIP A to TRIP B, press the reset switch. When pressed for 1 second, it will resetto 0.
B310B01GK-EAT ODOMETER/TRIP ODOMETERHGK028C
Function of digital odometer/trip odom- eter
Pushing in the reset switch on the right side of speedometer when the ignition switch is turned"ON" will display the following sequence:
HGK055B
132

CONTROLS AND EQUIPMENT
1- 32 3. DRIVE TIME
HGK058
A Type
B Type
o When the battery has been reinstalled after being discharged or disconnected, drive more than 20 miles for an accurate distance toempty.
NOTE:
o If the distance to empty is indicated "- -", have the trip computer system checked byyour authorized Hyundai dealer.
o The distance to empty can differ from the actual tripmeter according to driving con-ditions.
o The distance to empty can vary according to the driving conditions, driving patternor vehicle speed.
2. AVERAGE SPEED
o This mode indicates the average speed trav- elled since the last average speed reset.
o Pressing the reset switch for more than 1 second, when the average speed is being displayed, clears the average speed to zero. HGK057B
A Type
B Type
1. DISTANCE TO EMPTY DISTANCE TO EMPTY
AVERAGE SPEED DRIVE TIME
o This mode provides the estimated distance to empty from the current fuel level in the fuel tank.
o The trip computer may not register additional fuel if less than 6 liters of fuel are added to thevehicle. HGK056
A Type
B Type
o This mode indicates the drive time travelled since the last drive time reset.
o Pressing the reset switch for more than 1 second, when the drive time is being dis- played, clears the drive time to zero.

CONTROLS AND EQUIPMENT
1- 34 SB220D1-E HIGH AND LOW BEAM To turn on the headlight high beams, push the lever forward (away from you). For low beams,pull the lever back (toward you). The appropriateheadlight beam indicator light will come on at thesame time.
SB220E1-E HEADLIGHT FLASH
SB220C3-ELIGHTING SWITCH The vehicle sidelamps and headlamps are oper- ated by rotating the end of the turn signal switchbarrel. To operate the sidelight, rotating the switchto the first detent with ignition switch at the "OFF"position will cause the lamps to illuminate. Tooperate the headlamps, the turn signal switchbarrel should be rotated to the second detent.The headlamps will only operate when the igni-tion switch is at the "On" position. If the ignitionswitch is turned to the "Off" position, only thesidelight will function. The headlight may be flashed by pulling the turnsignal switch lever towards the steering wheel.The headlight will be extinguished when theswitch is released.
To indicate an intention to change lanes, movingthe lever slightly towards the direction of therelevant turn signal will cause the turn signallamps to flash. When the lever is released, it willreturn to the "off" position.
HGK039-D
To operate the automatic light feature, turn the barrel on the end of the multi-function switch. Ifyou set the multi-function switch to "AUTO", thetail lights and headlights will be turned automati-cally on or off according to external illumination.
B340G01L-GAT Auto Light (Not all models)
HGK041-D
HGK233-D
NOTE: The ignition must be in the "ON" position toturn on the headlights. Parking light auto cut If you do not turn the parking lights "OFF" afterdriving, the parking lights will automatically shut"OFF" when the driver's door is opened.To turn them "ON" again you must simply turn theignition key to the "ON" position.

CONTROLS AND EQUIPMENT1- 35
SB230B1-E VARIABLE INTERMITTENT WIPE FACILITY (Not all models)
B350A01GK-EAT WINDSCREEN WIPER/WASHER SWITCH The windscreen wiper switch, dependent upon model, has three operating positions.1. Intermittent wiper operation. (Not all models)2. Low speed operation.3. High speed operation. NOTE: To prevent damage to the wiper system, donot attempt to wipe away heavy accumula-tions of snow or ice.Accumulated snow and ice should be re-moved manually. If there is only a light layerof snow or ice, operate the heater in thedefrost mode to melt the snow or ice beforeusing the wiper. The variable intermittent wipe facility is operatedby moving the windscreen wiper switch to thefirst position. The time period between wipes isadjusted by moving the rotary control on thewindscreen wiper switch barrel. B350B01O-EAT WINDSCREEN WASHER OPERATION To use the windscreen washer, pull the wiper/ washer lever toward the steering wheel. Whenthe washers are operated, the wipers automati-cally make two passes across the windscreen.The washers continue to operate until the lever isheld at the washer position. NOTE:
o Do not operate the washers for more than
15 seconds continuously or when the flu-id reservoir is empty.
HGK042-D
(1)
(2) (3)
HGK043-D
Mist Wiper Operation
HGK045-D
If a single wipe is desired in mist, move the windscreen wiper and washer control lever up.
HGK044-D