buttons Hyundai Coupe 2005 Owner's Manual

1FEATURES OF YOUR HYUNDAI
58CIGARETTE LIGHTERINSTRUMENT PANEL LIGHT CONTROL (RHEOSTAT)
B410A01A-AAT (If Installed) The instrument panel lights can be made brighter or dimmer by turning the instrument panel light control knob. B420A02A-AAT For the cigarette lighter to work, the key must be in the "ACC" position orthe "ON" position. To use the cigarette lighter, push it all the way into its socket. When theelement has heated, the lighter will pop out to the "ready" position. Do not hold the cigarette lighter pressedin. This can damage the heating ele- ment and create a fire hazard. If it is necessary to replace the ciga-rette lighter, use only a genuine Hyundai replacement or its approved equiva- lent.
HGK2150
HGK2118DIGITAL CLOCK
B400A01A-AAT There are three control buttons for the digital clock. Their functions are:
HOUR - Push "H" to advance the hour indicated.
MIN - Push "M" to advance the minute indicated.
RESET- Push "R" to reset minutes to
":00" to facilitate resetting the clock to the correct time. When this is done:
Pressing "R" between 10 : 30 and 11 :29 changes the readout to 11 : 00. Pressing "R" between 11 : 30 and 12 :29 changes the readout to 12 : 00. Type A
HGK2117
Type B

1
FEATURES OF YOUR HYUNDAI
61SUNSHADE
B470A01S-AAT (If Installed) The sunshade can be opened and closed by sliding it forward or rearward when the sunroof is closed. The sun-shade will open automatically when the sunroof is opened, but it must be closed manually. HGK2026
!WARNING:
Never adjust the sunshade while driving.
!
!
SUNROOF
B460A01S-AAT (If Installed) The sunroof can be operated with the ignition key in the "ON" position. B460B02GK-GAT Opening the Sunroof System Release the button when the sunroof reaches the desired position.
The sunroof can be electrically openedor closed with the ignition key in the"ON" position. The sunroof is moved to its fully open position by pushing the " " button, and to stop at the desiredposition, push in any buttons ( , , Up, Down). To close, press and hold the " " button. CAUTION:
o Do not open the sunroof in se- verely cold temperature or when it is covered with ice or snow.
o Periodically remove any dirt that
may have accumulated on theguide rails. WARNING:
o Do not close a sunroof if anyone's hands, arms or body are between the sliding glass and the sunroof sash, as this could result in in- jury.
o Do not place your head or arms out of the sunroof opening at anytime.
HGK2022

1FEATURES OF YOUR HYUNDAI
88
NOTE: Never place anything over the sen- sor which is located on the instru-ment panel to ensure better control of the heating and cooling system. Photo sensor
B995A01Y-GAT AMBIENT TEMPERATURE SWITCH Pressing the button displays the ambient temperature on the display.
OUTSIDE
TEMP B980A01Y-AAT MANUAL OPERATION The heating and cooling system can be controlled manually as well by pushingbuttons other than the "AUTO" button. In this state, the system sequentially works according to the order of buttonsselected. The function of the buttons which are not selected will be controlled automati-cally. Press the "AUTO" button in order to convert to automatic control of the sys-tem.
HGK2076
HGK2109

1FEATURES OF YOUR HYUNDAI
96AUDIO SYSTEM
H240A01O-GAT STEREO RADIO OPERATION (H250) (If Installed)
1. POWER ON/OFF, VOLUME Control Knob H250A01GK
2. BASS/BALANCE Control Knob(BASS/BAL)
3. TREBLE/FADER Control Knob (TREB/FAD)
4. TUNE/SEEK Select Button
5. BAND Selector
6. PRESET Buttons7. SCAN Button

1FEATURES OF YOUR HYUNDAI
98
!
HOW TO PRESET STATIONS Six AM and twelve FM stations may be programmed into the memory of theradio. Then, by simply pressing the band select button and/or one of the six station select buttons, you may recallany of these stations instantly. To pro- gram the stations, follow these steps:
o Press band selector to set the band
for AM, FM1, or FM2.
o Select the desired station to be stored by seek or manual tuning.
o Determine the preset station select
button you wish to use to access that station.
o Press the station select button for
more than two seconds. A selectbutton indicator will show in the dis- play indicating which select button you have depressed. The frequencydisplay will flash after it has been stored into the memory with a beep sound. You should then release thebutton, and proceed to program the next desired station. A total of 18 stations can be programmed by se-lecting one AM and two FM stations per button. o When completed, any preset station
may be recalled by selecting AM, FM1 or FM2 band and the appropri- ate station button.
7. SCAN Button When the scan button is pressed, the frequency will increase and the receiv- able stations will be tuned in one afteranother, receiving each station for 5 seconds. To stop scanning, press the scan button again.
CAUTION:
o Do not place beverages close to the audio system. The audio sys- tem mechanism may be damaged if you spill them.
o Do not impact on the audio sys- tem, or the audio system mecha-nism could be damaged.

1
FEATURES OF YOUR HYUNDAI
103
!
7. PRESET STATION SELECT
Button
Six (6) stations for AM, FM1 or FM2 respectively can be preset in the elec-tronic memory circuit on this unit. HOW TO PRESET STATIONS Six AM and twelve FM stations may be programmed into the memory of the radio. Then, by simply pressing the band select button and/or one of the sixstation select buttons, you may recall any of these stations instantly. To pro- gram the stations, follow these steps:
o Press band selector to set the band for AM, FM1 or FM2.
o Select the desired station to be stored by seek, scan or manual tuning.
o Determine the preset station select button you wish to use to access that station. o Press the station select button for
more than two seconds. A select button indicator will show in the dis- play indicating which select button you have depressed. The frequencydisplay will flash after it has been stored into the memory. You should then release the button,and proceed to program the next desired station. A total of 18 stations can be programmed by selecting oneAM and two FM stations per button.
o When completed, any preset station
may be recalled by selecting AM,FM1 or FM2 band and the appropri- ate station button.
CAUTION:
o Do not place beverages close to the audio system. The audio sys-tem mechanism may be damaged if you spill them.
o Do not impact on the audio sys- tem, or the audio system mecha-nism could be damaged.

1FEATURES OF YOUR HYUNDAI
110
6. EQ Button
J290A01JM-GAT STEREO RADIO OPERATION (J290) (If installed)
J290A01JM
1. POWER ON/OFF/VOLUME Control Knob
2. BAND Select Button
3. SEEK Select Button 4. PRESET STATION Select Buttons 5. BEST STATION
MEMORY
7. TUNE Select Knob /
MODE Select Knob

1
FEATURES OF YOUR HYUNDAI
111
J290B01JM-GAT
1. POWER ON-OFF/VOLUME Control Knob
The radio unit may be operated when the ignition key is in the "ACC" or "ON"position. Press the button to switch the power on. The display shows the radio frequency in the radio mode, the tapedirection indicator in the tape mode, or
CD track in the CD AUTO CHANGER mode. To switch the power off, pressthe button again. VOLUME Control Rotate the knob clockwise to increase the volume and turn the knob counter- clockwise to reduce the volume.
2. BAND Selector Pressing the button changes the AM, FM1 and FM2 bands. The mode se-lected is shown on the display. o Press AM/FM selector to set the
band for AM, FM1 and FM2.
o Select the desired station to be stored by seek, scan or manual tuning.
o Determine the preset station select
button you wish to use to access that station.
o Press the station select button for
more than two seconds. A selectbutton indicator will show in the dis- play indicating which select buttonyou have depressed. The frequency display will flash after it has been stored into the memory. You shouldthen release the button, and proceed to program the next desired station. A total of 18 stations can be pro-grammed by selecting one AM and two FM station per button.
o When completed, any preset station may be recalled by selecting AM,FM1 or FM2 band and the appropri- ate station button.
3. SEEK Select Button
(Automatic Channel Selection)
Press the SEEK select button 1 sec. or
more. When the ( ) side is pressed, theunit will automatically tune to the next
higher frequency and when the ( ) side
is pressed, it will automatically tune to the next lower frequency.
4. PRESET STATION Select
Buttons
Six (6) stations for AM, FM and FM2 respectively can be preset in the elec- tronic memory circuit. HOW TO PRESET STATIONS Six AM and twelve FM stations may be programmed into the memory of the radio. Then, by simply pressing the AM/ FM select button and/or one of the six station select buttons, you may recall any of these stations instantly. To pro-gram the stations, follow these steps:

1FEATURES OF YOUR HYUNDAI
120
B260A01GK-GAT INFINITY SOUND SYSTEM (B260)(If installed)
1. On/Off Switch ( )
2. Tone Button ( )
3. Road traffic announcement button ( )
4. Operating mode switching button ( Mode)
5. Function button ( Function) 6. Waveband switching button ( Band)
7. CD eject button ( )
8. Volume control
9. Multifunction buttons
10. Display
11. Right rotary control
B260A01GK

1FEATURES OF YOUR HYUNDAI
122
4. Activate tone menu Press button. The tone menu is activated. The following functions canbe called up: BASS (Bass), TREB (Treble), BAL (balance), FAD (Fader), LOUD (Loudness) and STEREO (Re-ception optimization). Bass and treble setting for the AM / FM wavebands, for road traffic announce-ments and CD operation are stored separately (values form -7 to +7). The setting for fader balance and loudness(no loudness with AM) are stored to- gether for all operating modes (values from -7 to +7). 5. Adjust bass Press button and then multifunction button (1) "-" or "+". BASS and the setvalue are displayed. Set the desired bass via both buttons. Center setting: Press both buttons si- multaneously. 6.Adjust Treble Press button and then multifunction button (2) "-" or "+". TREB and the setvalue are displayed. Set the desired treble via both buttons. Center setting: Press both buttons si- multaneously.
7. Adjust Balance Press button and then multifunction button (3) " " or " ". BAL and the set value are displayed. Set the desiredbalance via both buttons. Center setting: Press both buttons si- multaneously. 8. Fader Press button and then multifunction button (4) " " or " ". FAD and the setvalue are displayed. Set the desired fade level via both buttons. Center setting: Press both buttons si-multaneously.
9. Loudness On / Off Press button and then multifunction button (5) "LD". LOUD ON or LOUD OFF are displayed. The loudness canbe switched on or off alternately by pressing the multifunction button. 10.Linear Adjustment It controls the amplification ratio from high to low tone. Activate tone menu.Then again press and hold button for more than 2 seconds. The tone values for the set signal source (e.g.radio/FM) are set to an average value FM LINEAR. Press and hold button for more than4 seconds. All tone values for the signal sources radio and tape /CD are set to an average value ALL LINEAR.
B260B02GK