VIN Hyundai Creta 2016 Owner's Manual

7-41
7
Maintenance
AIR ClEANER
Filter replacement
You can clean the filter when inspect
ing the air cleaner element.
Clean the filter by using compressed
air.
1. Loosen the air cleaner cover attaching clips and open the cover. 2. Wipe the inside of the air cleaner.
3. Replace the air cleaner filter.
4. Lock the cover with the cover
attaching clips. Replace the filter according to the
Maintenance Schedule.
If the vehicle is operated in extreme
ly dusty or sandy areas, replace the element more often than the usualrecommended intervals. (Refer to“Maintenance under severe usageconditions” in this chapter.)
•Do not drive with the air cleaner
removed; this will result in exces
sive engine wear.
•When removing the air cleaner fil
ter, be careful that dust or dirt does
not enter the air intake, or damage
may result.
•We recommend that you use parts
for replacement from an authorized
HYUNDAI dealer.
NOTICE
OGS075010
OGS075011

7-55
7
Maintenance
Wheel alignment and tire bal
ance
The wheels on your vehicle were
aligned and balanced carefully at the
factory to give you the longest tire life
and best overall performance.
In most cases, you will not need to
have your wheels aligned again.
However, if you notice unusual tire
wear or your vehicle pulling one way
or the other, the alignment may need
to be reset.
If you notice your vehicle vibrating
when driving on a smooth road, your
wheels may need to be rebalanced.
Improper wheel weights can damage
your vehicle's aluminum wheels. Use
only approved wheel weights.
Tire replacement
If the tire is worn evenly, a tread wear
indicator will appear as a solid band
across the tread. This shows there is
less than 1.6 mm (1/16 inch) of tread
left on the tire. Replace the tire when
this happens.
Do not wait for the band to appear
across the entire tread before replac
ing the tire.
When replacing the tires, recheck
and tighten the wheel nuts after driv
ing about 1,000 km (620 miles). If the
steering wheel shakes or the vehicle
vibrates while driving, the tire is out
of balance. Align the tire balance. If
the problem is not solved, we recom
mend that you contact an authorized
HYUNDAI dealer.
NOTICE
NOTICE
OEN076053
Tread wear indicator

7-59
7
Maintenance
4. Tire ply composition and materi
al
The number of layers or plies of rub
bercoated fabric in the tire. Tire
manufacturers also must indicate the
materials in the tire, which include
steel, nylon, polyester, and others.
The letter "R" means radial ply con
struction; the letter "D" means diago
nal or bias ply construction; and the
letter "B" means beltedbias ply con
struction.
5. Maximum permissible inflation
pressure
This number is the greatest amount
of air pressure that should be put in
the tire. Do not exceed the maximum
permissible inflation pressure. Refer
to the Tire and Loading Information
label for recommended inflation
pressure.
6. Maximum load rating
This number indicates the maximum
load in kilograms and pounds that
can be carried by the tire. When
replacing the tires on the vehicle,
always use a tire that has the same
load rating as the factory installed
tire.
7. Uniform tire quality grading
Quality grades can be found where
applicable on the tire sidewall
between tread shoulder and maxi
mum chapter width.
For example:
TREAD wear 200
TRACTION AA
TEMPERATURE A
Tire age
Tires degrade over time, even
when they are not being used.
Regardless of the remaining
tread, it is recommended that tires
generally be replaced after six (6)
years of normal service. Heat
caused by hot climates or frequent
high loading conditions can accel
erate the aging process. Failure
to follow this warning could cause
sudden tire failure, which could
lead to a loss of control and an
accident involving serious injury or
death.
WARNING

7-60
Maintenance
Tread wear
The tread wear grade is a compara
tive rating based on the wear rate of
the tire when tested under controlled
conditions on a specified govern
ment test course. For example, a tire
graded 150 would wear oneanda
half times (1) as well on the gov
ernment course as a tire graded 100.
The relative performance of tires
depends upon the actual conditions
of their use, however, and may
depart significantly from the norm
due to variations in driving habits,
service practices and differences in
road characteristics and climate.
These grades are molded on the
sidewalls of passenger vehicle tires.
The tires available as standard or
optional equipment on your vehicle
may vary with respect to grade.
Traction AA, A, B & C
The traction grades, from highest to
lowest, are AA, A, B and C. Those
grades represent the tire’s ability to
stop on wet pavement measured
under controlled conditions on spec
ified government test surfaces of
asphalt and concrete. A tire marked
C may have poor traction perform
ance.
Temperature A, B & C
The temperature grades are A (the
highest), B, and C, representing the
tire’s resistance to the generation of
heat and its ability to dissipate heat
when tested under controlled condi
tions on a specified indoor laboratory
test wheel.
Sustained high temperature can
cause the material of the tire to
degenerate and reduce tire life, and
excessive temperature can lead to
sudden tire failure. Grades B and A
represent higher levels of perform
ance on the laboratory test wheel
than the minimum required by law.
The traction grade assigned to this
tire is based on straightahead
braking traction tests, and does
not include acceleration, corner
ing, hydroplaning, or peak traction
characteristics.
WARNING

7-61
7
Maintenance
Low aspect ratio tire
(if equipped)
The low aspect ratio tires, of which
aspect ratio is below 50, are
equipped with for the sporty look.
Riding with high aspect ratio tires
may be uncomfortable with unpleas
ant noises, because the low aspect
ratio tires are optimized for handling
and breaking.The sidewall of the low aspect ratio
tire is thinner than the high aspect
ratio tire. Thus, the wheel and the tire
may be easily damaged. Thus, follow
the below instructions.
Cautiously drive the vehicle on a
rough road or off the road.
Otherwise, the tires and wheels
may be damaged. After driving
those areas, inspect the tires and
wheels.
Slowly drive the vehicle to pass
over a pothole, speed bump, man
hole, or curb stone. Otherwise, the
tires and wheels may be damaged.
Upon having an impact on the tire,
we recommend you to have the
tires inspected by an authorized
HYUNDAI dealer.
Inspect the tires every 3,000 km to
prevent damage.
NOTICE
Tire temperature
The temperature grade for this tire
is established for a tire that is
properly inflated and not over
loaded. Excessive speed, under
inflation, or excessive loading,
either separately or in combina
tion, can cause heat buildup and
sudden tire failure. This can cause
loss of vehicle control and serious
injury or death.
WARNING

7-62
Maintenance
•It is difficult to recognize tire dam
age only with eyes. However, we
recommend you to have the tire
checked or replaced upon detect
ing even the slightest tire damage.
The tire damage may leak air from
the tire.
•Tire damage, caused by driving on
a rough road, pothole, manhole or
curb stone, or off the road, is not
covered by the manufacturer’s
warranty.
•For further information about the
tire, refer to the label on the tire
sidewall.
NOTICE

7-65
7
Maintenance
3. Pull the suspected fuse straight
out. Use the fuse puller provided in
the engine compar tment fusepanel.
4. Check the removed fuse; replace it if it is blown.
5. Push in a new fuse of the same rating, and make sure it fits tightly
in the clips.
If it fits loosely, we recommend that
you consult an authorized HYUNDAI
dealer.
If you do not have a spare, use a fuse of the same rating from a circuityou may not need for operating thevehicle, such as the cigarette lighterfuse.
If the electrical components do not
work and the fuses are OK, check
the fuse panel in the engine com
partment. If a fuse is blown, it must
be replaced. Fuse switch
Always, put the fuse switch at the ON position.
If you move the switch to the OFF
position, some items such as audio
and digital clock must be reset and
transmitter (or smart key and burglar
alarm) may not work properly.
Always place the fuse switch in the
ON position while driving the vehicle.
NOTICE
OGS075064
OGS075018

7-78
Maintenance
lIGhT BulBS
Consult an authorized HYUNDAI
dealer to replace most vehicle light
bulbs. It is difficult to replace vehicle
light bulbs because other parts of the
vehicle must be removed before you
can get to the bulb. This is especially
true for removing the headlight
assembly to get to the bulb(s).
Removing/installing the headlight
assembly can result in damage to
the vehicle.Information
After heavy driving, rain or washing
headlight and taillight lenses could
appear frosty. This condition is caused
by the temperature difference between
the lamp inside and outside.
This is similar to the condensation on
your windows inside your vehicle dur
ing the rain and doesn’t indicate a
problem with your vehicle. If the
water leaks into the lamp bulb circuit
ry, we recommend that the system be
checked by an authorized HYUNDAI
dealer.
Be sure to replace the burnedout
bulb with one of the same wattage
rating. Otherwise, it may cause dam
age to the fuse or electric wiring sys
tem.
NOTICE
i
Prior to replacing a light, depress
the foot brake, move the shift lever
into the P (Park, for automatic
transaxle vehicle) or neutral (for
manual transaxle vehicle), apply
the parking brake, place the igni
tion switch in the LOCK/OFF posi
tion, and take the key with you
when leaving the vehicle to avoid
sudden movement of the vehicle
and to prevent possible electric
shock.
Be aware the bulbs may be hot
and may burn your fingers.
WARNING

7-83
7
Maintenance
6. Install a new headlight bulb and
snap the headlight bulb retaining
wire into position by aligning the
wire with the groove on the bulb.
7. Connect the headlight bulb socket connector.
8. Install the headlight bulb cover by turning it clockwise.
Information
BiFunction projection
headlamp
This headlamp is bifunction type that
switches the low beam to high or the
high beam to low using solenoid sys
tem. So, the moving sound may be
heard when the headlamp switches
the low beam to high or the high beam
to low and it does not indicate mal
function of the headlamp.
Turn signal light
1. Remove the turn signal light bulb cover by turning it counterclock
wise.
2. Remove the socket from the assembly by turning the socket
counterclockwise until the tabs on
the socket align with the slots on
the assembly.
3. Insert a new bulb by inserting it into the socket and rotating it until
it locks into place.
4. Install the socket in the assembly by aligning the tabs on the socket
with the slots in the assembly.
Push the socket into the assembly
and turn the socket clockwise.
5. Install the turn signal light bulb cover by turning it clockwise.
Front fog light bulb replacement
1.Remove the under cover by rotating the screws and bolts.
2.Reach your hand into the back of the front bumper.
3.Disconnect the power connector from the socket.
4.Remove the bulbsocket from the housing by turning the socket
counterclockwise until the tabs on
the socket align with the slots on
the housing.
5.Install the new bulbsocket into the housing by aligning the tabs on the
socket with the slots in the hous
ing. Push the socket into the hous
ing and turn the socket clockwise.
6.Connect the power connector to the socket.
7.Reinstall the front bumper under cover.
i

Interior light bulb replacement1. Using a flatblade screwdriver,gently pry the lens from the interi
or lamp housing.
2. Remove the bulb by pulling it straight out.
3. Install a new bulb in the socket.
4. Align the lens tabs with the interior lamp housing notches and snap
the lens into place.
Use care not to dirty or damage lens,
lens tab, and plastic housings.
NOTICE
7-88
Maintenance
Prior to working on the Interior
lamps, ensure that the “OFF” but
ton is depressed to avoid burning
your fingers or receiving an elec
tric shock.
WARNING
■Map lamp (if equipped)
■Room lampOGS075047/OGS075049/OGS075048
■Luggage room lamp