warning light Hyundai Creta 2016 Manual PDF

7-48
Maintenance
(Continued)
If any electrolyte gets
into your eyes, flush
your eyes with clean
water for at least 15 min
utes and get immediate
medical attention. If
electrolyte gets on your
skin, thoroughly wash
the contacted area. If
you feel a pain or a
burning sensation, get
medical attention imme
diately.
Wear eye protection
when charging or work
ing near a battery.
Always provide ventila
tion when working in an
enclosed space.
(Continued)
(Continued)
An inappropriately dis
posed battery can be
harmful to the environ
ment and human health.
Dispose the battery
according to your local
law(s) or regulation.
The battery contains
lead. Do not dispose of it
after use. Please return
the battery to an author
ized HYUNDAI dealer to
be recycled.
•When lifting a plasticcased bat
tery, excessive pressure on the
case may cause battery acid to
leak, resulting in personal injury.
Lift with a battery carrier or with
your hands on opposite corners.
(Continued)
(Continued)
Battery dangers
Always read the follow
ing instructions careful
ly when handling a bat
tery.
Keep lighted cigarettes
and all other flames or
sparks away from the
battery.
Hydrogen, a highly
combustible gas, is
always present in bat
tery cells and may
explode if ignited.
Keep batteries out of
the reach of children
because batteries con
tain highly corrosive
SULFURIC ACID. Do
not allow battery acid to
contact your skin, eyes,
clothing or paint finish.
(Continued)
WARNING

7-56
Maintenance
Wheel replacement
When replacing the metal wheels for
any reason, make sure the new
wheels are equivalent to the original
factory units in diameter, rim width
and offset.
Replacing tires
To reduce the chance or serious
or fatal injuries from an accident
caused by tire failure or loss of
vehicle control:
•Replace tires that are worn,
show uneven wear, or are dam
aged. Worn tires can cause loss
of braking effectiveness, steer
ing control, and traction.
•Do not drive your vehicle with
too little or too much pressure in
your tires. This can lead to
uneven wear and tire failure.
•When replacing tires, never mix
radial and biasply tires on the
same car. You must replace all
tires (including the spare) if mov
ing from radial to biasply tires.
(Continued)
(Continued)
WARNING •Using tires and wheel other than
the recommended sizes could
cause unusual handling charac
teristics and poor vehicle con
trol, resulting in a serious acci
dent.
•Wheels that do not meet
HYUNDAI's specifications may
fit poorly and result in damage to
the vehicle or unusual handling
and poor vehicle control.
•The ABS works by comparing
the speed of the wheels. Tire
size can affect wheel speed.
When replacing tires, all 4 tires
must use the same size original
ly supplied with the vehicle.
Using tires of a different size can
cause the ABS (Antilock Brake
System) and ESC (Electronic
Stability Control) to work irregu
larly. (if equipped)
A wheel that is not the correct size
may adversely affect wheel and
bearing life, braking and stopping
abilities, handling characteristics,
ground clearance, bodytotire
clearance, snow chain clearance,
speedometer and odometer cali
bration, headlight aim and bumper
height.
WARNING

7-63
7
Maintenance
FuSES
A vehicle’s electrical system is pro
tected from electrical overload dam
age by fuses.
This vehicle has 2 fuse panels, one
located in the driver’s side panel bol
ster, the other in the engine compart
ment near the battery.
If any of your vehicle’s lights, acces
sories, or controls do not work, check
the appropriate circuit fuse. If a fuse
has blown, the element inside the
fuse will be melted.
If the electrical system does not
work, first check the driver’s side
fuse panel.
Before replacing a blown fuse, dis
connect the negative battery cable.
Always replace a blown fuse with
one of the same rating.
If the replacement fuse blows, this
indicates an electrical problem. Avoid
using the system involved and imme
diately consult an authorized
HYUNDAI dealer.
Three kinds of fuses are used: blade
type for lower amperage rating, SlowBlow type and multi fuse for higheramperage ratings.
Do not use a screwdriver or any
other metal object to remove fuses
because it may cause a short circuit
and damage the system.
Information
The actual fuse/relay panel label may
differ from equipped items. i
NOTICE
OTA070039
Normal
Normal
■ Slow Blow type
■ Multi fuse
BBlloowwnn
Normal
■
Blade type
BBlloowwnn
BBlloowwnn
Fuse replacement
•Never replace a fuse with any
thing but another fuse of the
same rating.
•A higher capacity fuse could
cause damage and possibly a
fire.
•Never install a wire or aluminum
foil instead of the proper fuse
even as a temporary repair. It
may cause extensive wiring
damage and a possible fire.
WARNING

7-78
Maintenance
lIGhT BulBS
Consult an authorized HYUNDAI
dealer to replace most vehicle light
bulbs. It is difficult to replace vehicle
light bulbs because other parts of the
vehicle must be removed before you
can get to the bulb. This is especially
true for removing the headlight
assembly to get to the bulb(s).
Removing/installing the headlight
assembly can result in damage to
the vehicle.Information
After heavy driving, rain or washing
headlight and taillight lenses could
appear frosty. This condition is caused
by the temperature difference between
the lamp inside and outside.
This is similar to the condensation on
your windows inside your vehicle dur
ing the rain and doesn’t indicate a
problem with your vehicle. If the
water leaks into the lamp bulb circuit
ry, we recommend that the system be
checked by an authorized HYUNDAI
dealer.
Be sure to replace the burnedout
bulb with one of the same wattage
rating. Otherwise, it may cause dam
age to the fuse or electric wiring sys
tem.
NOTICE
i
Prior to replacing a light, depress
the foot brake, move the shift lever
into the P (Park, for automatic
transaxle vehicle) or neutral (for
manual transaxle vehicle), apply
the parking brake, place the igni
tion switch in the LOCK/OFF posi
tion, and take the key with you
when leaving the vehicle to avoid
sudden movement of the vehicle
and to prevent possible electric
shock.
Be aware the bulbs may be hot
and may burn your fingers.
WARNING

7-79
7
Maintenance
Headlight, position light, turn sig
nal light, static bending light and
front fog light bulb replacement
Type A
(1) Headlight (Low/High)
(2) Parking (Position) light
(3) Front turn signal light
(4) Front fog light (if equipped)
(5) Daytime running light (if equipped)
Information
If the headlight aiming adjustment is
necessary after the headlight assembly
is reinstalled, consult an authorized
HYUNDAI dealer.i
OGS075054
•Always handle them carefully,
and avoid scratches and abra
sions. If the bulbs are lit, avoid
contact with liquids. Never touch
the glass with bare hands.
Residual oil may cause the bulb
to overheat and burst when lit. A
bulb should be operated only
when installed in a headlight.
•If a bulb becomes damaged or
cracked, replace it immediately
and carefully dispose of it.
•Wear eye protection when
changing a bulb. Allow the bulb
to cool down before handling it.Halogen bulbs
•Halogen bulbs contain pressur
ized gas that will produce flying
pieces of glass if broken.
(Continued)
(Continued)
WARNING
OLMB073042L

7-82
Maintenance
Information
If the headlight aiming adjustment is
necessary after the headlight assembly
is reinstalled, consult an authorized
HYUNDAI dealer.
Headlight (Low/High) and static
bending light replacement
1. Open the hood.
2. Remove the headlight bulb cover by turning it counterclockwise.
3. Disconnect the headlight bulb socketconnector.
4. Unsnap the headlight bulb retain ing wire by depressing the end
and pushing it upward.
5. Remove the bulb from the head light assembly.
i
•Always handle them carefully,
and avoid scratches and abra
sions. If the bulbs are lit, avoid
contact with liquids. Never touch
the glass with bare hands.
Residual oil may cause the bulb
to overheat and burst when lit. A
bulb should be operated only
when installed in a headlight.
•If a bulb becomes damaged or
cracked, replace it immediately
and carefully dispose of it.
•Wear eye protection when
changing a bulb. Allow the bulb
to cool down before handling it.Halogen bulbs
•Halogen bulbs contain pressur
ized gas that will produce flying
pieces of glass if broken.
(Continued)
(Continued)
WARNING
OLMB073042L
OGS075051
Static bending light
Turn signal
Low/High

Interior light bulb replacement1. Using a flatblade screwdriver,gently pry the lens from the interi
or lamp housing.
2. Remove the bulb by pulling it straight out.
3. Install a new bulb in the socket.
4. Align the lens tabs with the interior lamp housing notches and snap
the lens into place.
Use care not to dirty or damage lens,
lens tab, and plastic housings.
NOTICE
7-88
Maintenance
Prior to working on the Interior
lamps, ensure that the “OFF” but
ton is depressed to avoid burning
your fingers or receiving an elec
tric shock.
WARNING
■Map lamp (if equipped)
■Room lampOGS075047/OGS075049/OGS075048
■Luggage room lamp

7-89
7
Maintenance
APPEARANCE CARE
Exterior care
Exterior general caution
It is very important to follow the label
directions when using any chemical
cleaner or polish. Read all warning
and caution statements that appear
on the label.
Finish maintenance
Washing
To help protect your vehicle’s finish
from rust and deterioration, wash it
thoroughly and frequently at least
once a month with lukewarm or cold
water.
If you use your vehicle for offroad
driving, you should wash it after each
offroad trip. Pay special attention to
the removal of any accumulation of
salt, dirt, mud, and other foreign
materials. Make sure the drain holes
in the lower edges of the doors and
rocker panels are kept clear andclean.
Insects, tar, tree sap, bird droppings,
industrial pollution and similar
deposits can damage your vehicle’s
finish if not removed immediately.
Even prompt washing with plain
water may not completely remove all
these deposits. A mild soap, safe for
use on painted surfaces, may beused.
After washing, rinse the vehicle thor
oughly with lukewarm or cold water.
Do not allow soap to dry on the finish. •Do not use strong soap, chemical
detergents or hot water, and do not
wash the vehicle in direct sunlight
or when the body of the vehicle is
warm.
•Be careful when washing the side
windows of your vehicle.
Especially, with highpressure
water, water may leak through the
windows and wet the interior.
•To prevent damage to the plastic
parts and lamps, do not clean with
chemical solvents or strong deter
gents.
NOTICE
Wet brakes
After washing the vehicle, test the
brakes while driving slowly to see if
they have been affected by water. If
braking performance is impaired,
dry the brakes by applying them
lightly while maintaining a slow for
ward speed.
WARNING

7-91
7
Maintenance
Brightmetal maintenance
• To remove road tar and insects,use a tar remover, not a scraper or
other sharp object.
• To protect the surfaces of bright metal parts from corrosion, apply a
coating of wax or chrome preser
vative and rub to a high luster.
• During winter weather or in coastal areas, cover the bright metal parts
with a heavier coating of wax or
preservative. If necessary, coat the
par ts with noncorrosive gasoli
neeum jelly or other protective
compound.
Underbody maintenance
Corrosive materials used for ice and
snow removal and dust control may
collect on the underbody. If these
materials are not removed, acceler
ated rusting can occur on the under
body parts such as the fuel lines,
frame, floor pan and exhaust system,
even though they have been treated
with rust protection.
Thoroughly flush the vehicle under
body and wheel openings with luke
warm or cold water once a month,
after offroad driving and at the end
of each winter. Pay special attention
to these areas because it is difficult
to see all the mud and dirt. It will do
more harm than good to wet down
the road grime without removing it.
The lower edges of the doors, rocker
panels, and frame members have
drain holes that should not clog with
dirt; trapped water in these areas can
cause rusting.
After washing the vehicle, test the
brakes while driving slowly to see
if they have been affected by
water. If braking performance is
impaired, dry the brakes by apply
ing them lightly while maintaining
a slow forward speed.
WARNING