warning Hyundai Elantra 2006 User Guide
[x] Cancel search | Manufacturer: HYUNDAI, Model Year: 2006, Model line: Elantra, Model: Hyundai Elantra 2006Pages: 277, PDF Size: 10.18 MB
Page 32 of 277

1FEATURES OF YOUR HYUNDAI
18
!WARNING:
o The purpose of the fold-down rear seat back and the fold-up rear seat cushion is to allow you tocarry more objects than could be accommodated. Do not allow pas- sengers to sit on the cargo areawhile the car is moving. This is not a proper seating position and no seat belts are available for usewhen the seat back is folded down. This could result in serious in- jury or death in case of an acci-dent or a sudden stop. Objects should not extend higher than the top of the front seatbacks.This could allow cargo to slide forward and cause injury or dam- age during sudden stops.
o WARNING LABEL: When return- ing the seat cushion to the seat-
ing position, place the seat belt
buckles on top of the cushion.
o When you return the folded down
seat back to its upright position,be sure to place the rear seat belt buckles on the seat bight between the seat cushion and seatback.
CAUTION:
After folding the rear seatback and seat cushion, the headrest can be stored in the trunk so that it will notbe thrown forward in the case of a sudden stop or an accident.
o When you return the seatback to its upright position, always be sure it is locked into position by pulling and pushing on the top of the seatback. Warning label
B080H01E-1!
B080G01E-GAT Folding Rear Seatback and Seat Cushion (5 Door) For convenience, the seatback and seat cushion may be folded down and up.
1. Remove the headrest.
2. Pull the strap of the seat cushion (A)
upward to fold up the seat cushion.
3. Pull the seatback locking knob (B)
on the seatback to fold-down theseatback.
4. Then, pull forward on the seatback
panel. B080G01E-1
Strap
A B
Page 33 of 277

1
FEATURES OF YOUR HYUNDAI
19
!
B140A01E
B140A01S-AAT For the safety of all passengers, lug- gage or other cargo should not be piled higher than the top of the seatback. In addition, do not place objects on therear shelf as they may move forward during braking or in an accident and may strike and injure vehicle passen-gers. REAR SEAT WARNING
B100A01E-AAT (If installed) The seat warmer is provided to warm the front seats during cold weather.With the ignition key in the "ON" posi- tion, push either of the switches to warm the driver's seat or thepassenger's seat. During mild weather or under condi- tions where the operation of the seatwarmer is not needed, keep the switches in the "OFF" position. NOTE: The seat warmer may not operate if ambient temperature is warm enough.
HXDFL100
SEAT WARMER
WARNING:
Be very careful not to injure by low temperature burn or an attack of fe- ver as following occupants; infants,children, old man, drunken man, people who is taken sleeping drug or cold remedy.
Page 35 of 277

1
FEATURES OF YOUR HYUNDAI
21
B150F01A-AAT One Person Per Belt Two people (including children) should never attempt to use a single seat belt.This could increase the severity of injuries in case of an accident. B150G01A-AAT Do Not Lie Down To reduce the chance of injuries in the event of an accident and to achieve maximum effectiveness of the restraint system, all passengers should be sit- ting up and the front seats should be inan upright position when the car is moving. A seat belt cannot provide proper protection if the person is lyingdown in the rear seat or if the front seat is in a reclined position.
!WARNING:
Sitting in a reclined position or ly- ing down when your vehicle is in motion can be dangerous. Even ifyou buckle up, your seat belts can't do their job when you're reclined. The shoulder belt can't do its jobbecause it won't be against your body. Instead, it will be in front of you. In a crash you could go into itwith great force, receiving serious neck or other injuries. The lap belt can't do its job either. In a crash the belt could go up over your abdomen. The belt forceswould be applied there, not at your strong pelvic bones. This could cause serious internalinjuries. For proper protection when the ve- hicle is in motion, have the seatbackupright. Then sit back in the seat and wear your seat belt properly. See page 1-23. B160B01A-AAT Periodic Inspection It is recommended that all seat belts be inspected periodically for wear ordamage of any kind. Parts of the sys- tem that are damaged should be re- placed as soon as possible.
B160A01A-AAT CARE OF SEAT BELTS Seat belt systems should never be disassembled or modified. In addition,care should be taken to assure that seat belts and belt hardware are not damaged by seat hinges, doors orother abuse.
!WARNING:
When you return the rear seatback to its upright position after being folded down, be careful not to dam- age the seat belt webbing or buckle. In addition, do not allow the seat belt webbing or buckle to get caughtor pinched in the rear seat.
Page 36 of 277

1FEATURES OF YOUR HYUNDAI
22
!
To adjust the height of the seat belt anchor, lower or raise the height ad-juster into an appropriate position. To raise the height adjuster, pull it up. To lower it, push it down while pressingthe height adjuster button. Release the button to lock the anchor into position. Try sliding the heightadjuster to make sure that it has locked into position.
You can adjust the height of the shoul- der belt anchor to one of 4 positions for maximum comfort and safety. If the height of the adjusting seat belt istoo near your neck, you will not be getting the most effective protection. The shoulder portion should be ad-justed so that it lies across your chest and midway over your shoulder near- est the door and not your neck. B170A01E
B170A04A-AAT HEIGHT ADJUSTABLE FRONT SEAT SHOULDER BELT(If installed)
WARNING:
o The height adjuster must be in the locked position when the vehicle is moving.
o The misadjustment of height of
the shoulder belt could reducethe effectiveness of the seat belt in a crash.
B160D01A-AAT When to Replace Seat Belts Entire in-use seat belt assembly or assemblies should be replaced if the vehicle has been involved in an acci- dent. This should be done even if nodamage is visible. Additional ques- tions concerning seat belt operation should be directed to your HyundaiDealer. B160C01A-AAT Keep Belts Clean and Dry Seat belts should be kept clean and dry. If belts become dirty, they can becleaned by using a mild soap solution and warm water. Bleach, dye, strong detergents or abrasives should not beused because they may damage and weaken the fabric.
Page 39 of 277

1
FEATURES OF YOUR HYUNDAI
25
!
HXDFL429
B220C01A-AAT To Release the Seat Belt When you want to release the seat belt, press the button in the locking buckle.
WARNING:
The center lap belt latching mecha- nism is different from those for therear seat shoulder belts. When fas- tening the rear seat shoulder belts or the center lap belt, make surethey are inserted into the correct buckles to obtain maximum protec- tion from the seat belt system andassure proper operation.
B220A01E
(a)
(c)
(b) (d)
1. Before fastening the rear seat cen- ter belt, confirm the metal tab (a) and buckle (b) are latched together.
2. After confirming that (a) and (b) are latched, pull the seat belt out of theretractor and insert the metal tab (c)into the buckle (d).
B220A01E-GAT SEAT BELTS - Center Rear Seat 3-Point System With EmergencyLocking Retractor (If installed)
B220A02Y
There will be an audible "click" when the tab locks in the buckle. The seatbelt automatically adjusts to the proper length only after the lap belt is adjusted manually so that it fits snugly aroundyour hips. If you lean forward in a slow, easy motion, the belt will extend and let you move around. If there is asudden stop or impact, the belt will lock into position. It will also lock if you try to lean forward too quickly.
Page 40 of 277

1FEATURES OF YOUR HYUNDAI
26CHILD RESTRAINT SYSTEM
B230A03A-GAT (If installed) Children riding in the car should sit in the rear seat and must always beproperly restrained to minimize the risk of injury in an accident, sudden stop or sudden maneuver. Accordingto accident statistics, children are safer when properly restrained in the rear seats than in the front seat. Largerchildren not in a child restraint should use one of the seat belts provided. You are required by law to use safetyrestraints for children. If small children ride in your vehicle you must put them in a child restraint system (safety seat).Children could be injured or killed in a crash if their restraints are not properly secured. For small children and ba-bies, a child seat or infant seat must be used. Before buying a particular child restraint system, make sure it fits yourcar and seat belts, and fits your child. Follow all the instructions provided by the manufacturer when installing thechild restraint system.
!
B220C01E
B220C01Y-GAY To Release the Seat Belt
When you want to release the seat belt, press the button in the locking buckle. WARNING:
The center belt latching mechanismis different from those for the rearseat shoulder belts. When fasten- ing the rear seat shoulder belts or the rear seat center belt, make surethey are inserted into the correct buckles to obtain maximum protec- tion from the seat belt system andassure proper operation.
!WARNING:
o When using the rear seat center belt, you must lock all metal tabs and buckles. If any metal tab or buckle is not locked, it will in-crease the chance of injury in the event of collision.
o Never unlock the metal tab (a)
and the buckle (b) with the fol-lowing exceptions.(1)In case of folding rear
seatbacks down.
(2)If transporting an object on
the rear seat may cause dam-age to the rear seat center belt.
o Lock the metal tab (a) and the buckle (b) immediately after fold-ing rear seatbacks up.
o To disconnect the metal tab (a) from the buckle (b), insert a sharp-ended tool into the groove lo-cated on the buckle (b). (4 DOOR only)
Page 41 of 277

1
FEATURES OF YOUR HYUNDAI
27
!WARNING:
o A child restraint system must be placed in the rear seat. Never install a child or infant seat on the front passenger's seat.Should an accident occur and cause the passenger's side airbag to deploy, it could severely in-jure or kill an infant or child seated in an infant or child seat. Thus, only use a child restraint in therear seat of your vehicle.
o Since a safety belt or child re-
straint system can become very hot if it is left in a closed vehicle, be sure to check the seat coverand buckles before placing a child there.
o When the child restraint system is not in use, store it in the trunkor fasten it with a safety belt so that it will not be thrown forwardin the case of a sudden stop or an accident.
o Children who are too large to be
in a child restraint should sit in the rear seat and be restrained with the available lap/shoulderbelts. Never allow children to ride in the front passenger seat.
o Always make sure that the shoul-
der belt portion of the outboardlap/shoulder belt is positioned midway over the shoulder, neveracross the neck or behind the back. Moving the child closer to the center of the vehicle may help provide a good shoulder belt fit. The lap belt portion of the lap/shoulder belt or the center seat lap belt must always be posi- tioned as low as possible on thechild's hips and as snug as pos- sible.
o If the seat belt will not properly fit
the child, Hyundai recommendsthe use of an approved booster seat in the rear seat in order toraise the child's seating height so that the seat belt will properly fit the child.o Never allow a child to stand up orkneel on the seat.
o Never use an infant carrier or
child safety seat that "hooks" over a seatback; it may not pro- vide adequate security in an ac-cident.
o Never allow a child to be held in
a person's arms while they are ina moving vehicle, as this could result in serious injury to the child in the event of an accidentor a sudden stop. Holding a child in a moving vehicle does not provide the child with any means of protection during an accident, even if the person holding thechild is wearing a seat belt.
o If the child restaint seat is not
anchored properly, the risk of achild being seriously injured or killed in a collision greatly in- creases.
Page 43 of 277

1
FEATURES OF YOUR HYUNDAI
29
!
If you need to tighten the belt, pull more webbing toward the retractor.When you unbuckle the seat belt and allow it to retract, the retractor will automatically revert back to its normalseated passenger emergency locking usage condition. NOTE:
o Before installing the child re-
straint system, read the instruc- tions supplied by the child re- straint system manufacturer.
o If the seat belt does not operate as described, have the systemchecked immediately by yourauthorized Hyundai dealer.
WARNING:
Do not install any child restraintsystem in the front passenger seat.Should an accident occur and cause the passenger's side airbag to de- ploy, it could severely injure or killan infant or child seated in an infant or child seat. Therefore, only use a child restraint system in the rearseat of your vehicle.
HSM386
Bolt, Holder (5/16"-22 mm) Washer, Conical Spring Holder, Child Restraint Hook
B230B02A-GAT Using a Child Restraint System with "Tether Anchorage" Sys-tem
For small children and babies, the use of a child seat or infant seat is required. This child seat or infant seat should be of appropriate size for the child andshould be installed in accordance with the manufacturer's instructions. It is further recommanded that the seat beplaced in the vehicle's rear seat since this can make an important contribu- tion to safety. Your vehicle is providedthree child restraint hook holders for installing the child seat or infant seat. Retainer WasherB230C03A-GAT Securing a Child Restraint Sys- tem with "Tether Anchorage"System(4 Door) Three child restraint hook holders are located on the rear seat package tray.
G230C02E
Tether anchor coverChild RestraintHook Holder
1. Open the tether anchor cover on the rear seat package tray.
Page 47 of 277

1
FEATURES OF YOUR HYUNDAI
33
NOTE: An ISOFIX-child-seat can only be installed if the seat has a vehicle- specific approval according to ECE-R44. Before using the ISOFIX-child- seat, which was bought for another car, ask your Hyundai-dealerwhether this seat-type is approved and recommended for your Hyundai. To secure the child restraint seat
B230D03E
1. To engage the child restraint seat to the ISOFIX anchor, insert the child restraint seat latch into the ISOFIX anchor. Listen for the audible "click"sound.
!WARNING:
o Do not install a child restraint seat at the center of the rear seat using the vehicle's ISOFIX anchors. The ISOFIX anchors are only provided for the left and right outboard rear seating positions. Do not misusethe ISOFIX anchors by attempting to attach a child restraint seat in the middle of the rear seat to theISOFIX anchors. In a crash, the child restraint seat ISOFIX attach- ments may not be strong enoughto secure the child restraint seat properly in the center of the rear seat and may break, causing seri-ous injury or death.
o When using the vehicle’s “ISOFIX”
system to install a child restraintsystem in the rear seat, all unused vehicle rear seat belt metal latch
2. Connect the tether strap hook to the
child restraint hook holder and tighten to secure the seat. Refer to "Securing a Child Restraint System with the Tether Anchorage System"on page 1-29.
plates or tabs must be latched securely in their seat belt buckles and the seat belt webbing must be retracted behind the child restraintto prevent the child from reaching and taking hold of unretracted seat
belts. Unlatched metal latch platesor tabs may allow the child to reach the unretracted seat belts which may result in strangulationand a serious injury or death to the child in the child restraint.
o Do not mount more than one child restraint to a child restraint loweranchorage point. The improper increased load may cause the an-chorage points or tether anchor to break, causing serious injury or death.
o Attach the ISOFIX or ISOFIX-com- patible child restraint seat onlyto the appropriate locationsshown in the illustration.
o Always follow the installation and
use instructions provided by themanufacturer of the child re- straint.
Page 49 of 277

1
FEATURES OF YOUR HYUNDAI
35
B180B01O
Driver's airbag1
2 3Passenger's airbag
The seat belt pre-tensioner system consists mainly of the following com- ponents. Their locations are shown in the illus- tration.
1.SRS airbag warning light
2.Seat belt pre-tensioner assembly
3.SRS control module
!
NOTE:
o Both the driver's and front passenger's pre-tensioner seat belts will be activated in certainfrontal collisions. The pre- tensioner seat belts can be acti- vated alone or, where the frontalcollision is severe enough, to- gether with the airbags. The pre- tensioners will be activated un-der these conditions even if the seat belts are not being worn at the time of the collision. WARNING:
To obtain maximum benefit from apre-tensioner seat belt:
1. The seat belt must be worn cor- rectly.
2. The seat belt must be adjusted to
the correct position. o When the pre-tensioner seat belts
are activated, a loud noise may be heard and fine dust, which may appear to be smoke, may be visible in the passenger compart-ment. These are normal operat- ing conditions and are not haz- ardous.
o Although it is harmless, the fine dust may cause skin irritationand should not be breathed forprolonged periods. Wash your hands and face thoroughly after an accident in which the pre-tensioner seat belts were acti- vated.