lights Hyundai Elantra 2006 Owner's Guide

6
DO-IT-YOURSELF MAINTENANCE
31CHECKING AND REPLACING FUSES
G200A01A-AAT
Replacing a Fusible Link
A fusible link will melt if the electrical circuits from the battery are ever over-loaded, thus preventing damage to the entire wiring harness. (This could be caused by a short in the systemdrawing too much current.) If this ever happens, have a Hyundai dealer determine the cause, repair the sys-tem and replace the fusible link. The fusible links are located in a fuse box for easy inspection. Good
Bad
G200B01E-AAT
Replacing Accessory Fuses
HXDFL200
CAUTION:
When replacing a fusible link, never
use anything but a new fusible link with the same or lower amper- age rating. Never use a piece ofwire or a higher-rated fusible link. This could result in serious dam- age and create a fire hazard.
! The fuse box for the lights and other electrical accessories will be found inthe backside of multi box located in the left side of the driver. On the backside of the multi box, you will finda list showing the circuits protected by each fuse. If any of your car's lights or other electrical accessories stop working, a blown fuse could be the reason. If the fuse has burned out, you will see thatthe metal strip inside the fuse has burned through. If you suspect a blown fuse, follow this procedure:
1. Turn off the ignition and all other switches.
2. Open the fuse box and examine each fuse. Remove each fuse by pulling it toward you (a small "fuse puller" tool is contained in the fusebox to simplify this operation).
3. Be sure to check all other fuses
even if you find one that appears tohave burned out.
G200A01E

6 DO-IT-YOURSELF MAINTENANCE
36HEADLIGHT AIMING ADJUSTMENT
G290A02E-GAT Before performing aiming adjustment,
make sure of the following.
1. Keep all tires inflated to the correct
pressure.
2. Place the vehicle on level ground and press the front bumper and rear bumper down several times.(Place the vehicle at a distance of 3,000 mm (118 in.) from the test wall.)
3. See that the vehicle is unloaded
(except for full levels of coolant,engine oil and fuel, and spare tire, jack, and tools). Have the driver or equivalent weight placed in driver'sseat.
4. Clean the head lights lenses and
turn on the headlights (low beam).
!WARNING:
Be sure to carefully wipe away any water drained out in this manner, because the fuel mixed in the wa-ter might be ignited and result in a fire.
G300B01A
1. Loosen the drain plug at the bottom of the fuel filter.
2. Tighten the drain plug when water no longer comes out.
3. Check to be sure that the warning lamp illuminates when the ignition key is turned to "ON", and that it goes off when the engine is started. If in doubt, consult your nearest authorized HYUNDAI dealer.
NOTE: It is recommended that water ac- cumulated in the fuel filter shouldbe removed by an authorized Hyundai dealer.

6
DO-IT-YOURSELF MAINTENANCE
37
Vertical Aiming
Horizontal Aiming
G290B03E-GAT
Adjustment After Headlight Assembly Replacement
G290B01L
LW
H
H Cut-off line be checked using an aiming screen as shown in the illustration. Turn on theheadlight switch. (Low Beam Position)
1. Adjust headlights so that main axis of light is parallel to the center lineof the body and is aligned with point"P" shown in the illustration.
2. Dotted lines in the illustration show
the center of the the headlights. Specifications: "H": Horizontal center line of headlights from ground.Low beam : 639 mm (25.2 in.) High beam : 619 mm (23.3 in.) "W": Distance between each headlightcenter.Low beam : 1124 mm (44.2 in.) High beam : 840 mm (33.0 in.) "L": Distance between the headlights andthe wall that the lights are testedagainst.: 3,000 mm (118 in.).
"P"
30mm (1.18 in.) Vertical line
G290A02E
5. Open the hood.
6. Draw the vertical line (through the center of each headlight beam pat-tern) and the horizontal line (through the center of each headlight beam pattern) on the aiming screen.And then, draw a horizontal paral-lel line at 30 mm (1.18 in.) underthe horizontal line.
7. Adjust each cut-off line of the low beam to the parallel line with aphillips screwdriver - VERTICAL AIMING.
8. Adjust each cut-off line of the low beam to the each vertical line with a phillips screwdriver - HORIZON-TAL AIMING. LHD
Horizontal line
Ground line
G290B01L-D
L
W
H
H Cut-off line
"P"
30mm (1.18 in.)
Vertical line
Horizontal line
Ground line
RHD
If the vehicle has had front body repair
and the headlight assembly has been replaced, the headlight aiming should

6
DO-IT-YOURSELF MAINTENANCE
45BULB WATTAGE
1357
4
G280A05E-GAT
G280A03E
16
31110
8
4 DOOR
5 DOOR
111012
8132
12
99
Part Name
High mounted rear stop light Luggage compartment light License plate light Rear fog light (If installed) Back -up light
No.
8 9
10 11 12 13
Wattage
55
55/5
51 215
1010
5 Socket type
BA 15s -
S8.5/8.5 S8.5/8.5 BA 15s
BAY 15d BA 15s
W2.1×9.5D
BA 15s
Part Name
Head Light (High beam) Head Light (Low beam) / Front Position Light Front Fog Light (If installed) Front Turn Signal LightSide Repeater (If installed) Door Edge Warning Light
No
.
1 2 3 45 67
Socket type P14,5s
PX 26d/
W2.1X9.5d P22d
BA15s
W2.1X9.5d W2.1×9.5D
S8.5/8.5
W2.1X9.5dWattage
5 5
2121
21/5
Rear combination light
4 Door5 Door
Map Light Room Light
4 Door 5 Door21
2,6(LED)
Turn signal light Stop/tail light
16 27
Interior