hood open HYUNDAI ELANTRA GT 2020 User Guide
[x] Cancel search | Manufacturer: HYUNDAI, Model Year: 2020, Model line: ELANTRA GT, Model: HYUNDAI ELANTRA GT 2020Pages: 495, PDF Size: 15.22 MB
Page 357 of 495

6-6
What to do in an emergency
7. Connect the other end of the sec- ond jumper cable to the black,
negative (-) chassis ground of
your vehicle (4).
Do not allow the jumper cables to
contact anything except the cor-
rect battery or jumper terminals or
the correct ground. Do not lean
over the battery when making
connections.
8. Start the engine of the assisting vehicle and let it run at approxi-
mately 2,000 rpm for a few min-
utes. Then start your vehicle.
If your vehicle will not start after a
few attempts, it probably requires
servicing. In this event please seek
qualified assistance. If the cause of
your battery discharging is not
apparent, have your vehicle checked
by an authorized HYUNDAI dealer. Disconnect the jumper cables in the
exact reverse order you connected
them:
1. Disconnect the jumper cable from
the black, negative (-) chassis
ground of your vehicle (4).
2. Disconnect the other end of the jumper cable from the black, neg-
ative (-) battery/chassis ground of
the assisting vehicle (3).
3. Disconnect the second jumper cable from the red, positive (+)
battery/jumper terminal of the
assisting vehicle (2).
4. Disconnect the other end of the jumper cable from the red, positive
(+) jumper terminal of your vehicle
(1). If your temperature gage indicates
overheating, you experience a loss
of power, or hear loud pinging or
knocking, the engine may be over-
heating. If this happens, you should:
1. Pull off the road and stop as soon
as it is safe to do so.
2. Place the shift lever in P (Park) and set the parking brake. If the air
conditioning is ON, turn it OFF.
3. If engine coolant is running out under the vehicle or steam is com-
ing out from the hood, stop the
engine. Do not open the hood until
the coolant has stopped running
or the steaming has stopped. If
there is no visible loss of engine
coolant and no steam, leave the
engine running and check to be
sure the engine cooling fan is
operating. If the fan is not running,
turn the engine off.
I IF
F
T
T H
H E
E
E
E N
N G
GI
IN
N E
E
O
O V
VE
ER
R H
H E
EA
A T
TS
S
Page 445 of 495

7-71
7
Maintenance
Headlamp (High/Low beam)
1. Open the hood.
2. Disconnect the negative batterycable.
3. Remove the headlamp bulb cover by turning it counterclockwise.
4. Disconnect the headlamp bulb socket-connector.
5. Remove the bulb from the head- lamp assembly.
6. Install a new headlamp bulb and snap the headlamp bulb retaining
wire into position by aligning the
wire with the groove on the bulb.
7. Connect the headlamp bulb sock- et-connector. 8. Install the headlamp bulb cover by
turning it clockwise.
Information
The headlamp aiming should be
adjusted after an accident or after the
headlamp assembly is reinstalled at an
authorized HYUNDAI dealer.
Turn signal
1. Open the hood.
2. Disconnect the negative batterycable.
3. Remove the socket from the assembly by turning the socket
counterclockwise until the tabs on
the socket align with the slots on
the assembly.
4. Remove the bulb from the socket by pressing it in and rotating it
counterclockwise until the tabs on
the bulb align with the slots in the
socket. Pull the bulb out of the
socket.
i
OPDE076077OPDE076076
â– High/Low beam
High
Low
Page 446 of 495

7-72
Maintenance
5. Install a new bulb by inserting it into the socket and rotating it until
it locks into place.
6. Install the socket in the assembly by aligning the tabs on the socket
with the slots in the assembly.
7. Push the socket into the assembly and turn the socket clockwise.
Parking lamp and daytime running
light
Your vehicle is equipped with LED
lamps. LED lamps do not have
replaceable bulbs. If the LED lamp
does not operate, have the vehicle
checked by an authorized HYUNDAI
dealer.Side marker
1. Open the hood.
2. Disconnect the negative batterycable.
3. Remove the socket from the assembly by turning the socket
counterclockwise until the tabs on
the socket align with the slots on
the assembly.
4. Remove the bulb from the socket by pulling out the bulb.
5. Insert a new bulb.
Type C
Type D (N line)
OAD075082N
OPD076041
OPDE078130
Page 488 of 495

I-8
Interior lamp AUTO cut..................................................3-91
Interior lights...................................................................3-91Front lamps.................................................................3-92
Interior lamp AUTO cut .............................................3-91
Luggage compartment lamp .......................................3-93
Rear lamp ...................................................................3-93
Vanity mirror lamp .....................................................3-93
Interior overview...............................................................1-4
Jump starting .....................................................................6-4\
Label Refrigerant label .........................................................8-12
Tire loading information label..................................5-124
Tire sidewall labeling .................................................7-43
Tire specification and pressure label ..........................8-12
Vehicle certification label ...........................................8-11
Lane change signals ........................................................3-90
Lane Keeping Assist (LKA) system ...............................5-80
Lap/shoulder belt ............................................................2-24 LCD display
LCD display modes ....................................................3-74
Assist mode ................................................................3-76
Quick guide help ........................................................3-75
Trip computer mode ...................................................3-75
Turn By Turn (TBT) mode.........................................3-76
User settings mode .....................................................3-77
Warning mode ............................................................3-77
LCD display messages Check AEB system .....................................................3-72
Check BRAKE SWITCH fuse ...................................3-69
Check BCW System ...................................................3-72
Check driver attention alert system............................3-72
Check headlamp FAN ................................................3-72
Check headlamp LED ................................................3-72
Check headlight ..........................................................3-71
Check LKA ................................................................3-72
Check high beam assist system ..................................3-72
Door, Hood, Liftgate open .........................................3-69
Engine has overheated................................................3-71
Key not detected .........................................................3-68
Key not in vehicle ......................................................3-68
Lights mode ................................................................3-70
Low fuel .....................................................................3-7\
1
Low Key Battery ........................................................3-68
Low pressure ..............................................................3-70
Index
J
L