lock Hyundai Genesis Coupe 2013 Owners Manual

Maintenance
48
7
Front windshield wiper blade
Type A
1. Raise the wiper arm and turn the wiper
blade assembly to expose the plastic
locking clip.
2. Compress the clip and slide the bladeassembly downward.
3. Lift it off the arm.
4. Install the blade assembly in the reverse order of removal. Type B
1. Raise the wiper arm.
1LDA5023
CAUTION
Do not allow the wiper arm to fall
against the windshield, since it may
chip or crack the windshield.
1JBA7037
1JBA7038
OHM078059
CAUTION
Do not allow the wiper arm to fallagainst the windshield, since it may chip or crack the windshield.

Maintenance
52
7
Reset items
Items should be reset after the battery
has been discharged or the battery hasbeen disconnected.
Sunroof (See section 4)
Trip computer (See section 4)
Climate control system
(See section 4)
Clock (See section 4)
Audio (See section 4)
WARNING
Before performing maintenance or recharging the battery, turn off all accessories and stop the
engine.
The negative battery cable must be removed first and installed
last when the battery is discon-nected.
We recommend that the opera- tion related to the battery be serv-
iced by an authorized HYUNDAI
dealer.
CAUTION
Keep the battery away from water
or any liquid.
When you replace the battery, we recommend that you use parts forreplacement from an authorized
HYUNDAI dealer.
WARNING - Recharging
battery
When recharging the battery,
observe the following precautions:
The battery must be removed from the vehicle and placed in an area with good ventilation.
Do not allow cigarettes, sparks, or flame near the battery.
Watch the battery during charg- ing, and stop or reduce the charg-
ing rate if the battery cells begin
gassing (boiling) violently or if
the temperature of the electrolyte
of any cell exceeds 49°C (120°F).
Wear eye protection when check- ing the battery during charging.
Disconnect the battery charger in the following order.
1. Turn off the battery charger main switch.
2. Unhook the negative clamp from the negative battery terminal.
3. Unhook the positive clamp from the positive battery terminal.

Maintenance
58
7
Compact spare tire replacement
(if equipped)
A compact spare tire has a shorter
tread life than a regular size tire.
Replace it when you can see the
tread wear indicator bars on the tire.The replacement compact spare tire
should be the same size and design
tire as the one provided with your
new vehicle and should be mountedon the same compact spare tire
wheel. The compact spare tire is notdesigned to be mounted on a regular
size wheel, and the compact spare
tire wheel is not designed for mount-
ing a regular size tire. Wheel replacement
When replacing the metal wheels for
any reason, make sure the new
wheels are equivalent to the original
factory units in diameter, rim widthand offset.
✽✽
NOTICE
The front tire size is different from
the rear tire size. So when you rotate
tires, check the tire and wheel size.
(Continued)
Using tires and wheel other than the recommended sizes
could cause unusual handling
characteristics and poor vehi-
cle control, resulting in a seri-ous accident.
Wheels that do not meet HYUNDAI’s specifications
may fit poorly and result in
damage to the vehicle or
unusual handling and poor
vehicle control.
The ABS works by comparing the speed of the wheels. Tire
size can affect wheel speed.
When replacing tires, all 4
tires must use the size origi-
nally supplied with the vehi-
cle. Using tires of a different
size can cause the ABS (Anti-
lock Brake System) and ESP
(Electronic Stability Program)
to work irregularly.
WARNING
A wheel that is not the correct
size may adversely affect wheel
and bearing life, braking and
stopping abilities, handling
characteristics, ground clear-
ance, body-to-tire clearance,
snow chain clearance,speedometer and odometer cal-
ibration, headlight aim and
bumper height.

765
Maintenance
Fuse switch
Always, put the fuse switch at the ON position.
If you move the switch to the OFF posi- tion, some items such as audio and digi-
tal clock must be reset and transmitter
(or smart key) may not work properly.Engine compartment fuse replacement
1. Turn the ignition switch and all otherswitches off.
2. Remove the fuse panel cover by pressing the tab and pulling up. 3. Check the removed fuse; replace it if it
is blown. To remove or insert the fuse, use the fuse puller in the engine com-
partment fuse panel.
4. Push in a new fuse of the same rating, and make sure it fits tightly in the clips.
If it fits loosely, we recommend that
you consult an authorized HYUNDAI
dealer.
OBK072042
OBK072021
OBK079048CAUTION
Always place the fuse switch in the
ON position while driving the vehi-cle.
CAUTION
After checking the fuse panel in theengine compartment, securely
install the fuse panel cover. If not,electrical failures may occur from water contact.

771
Maintenance
Fuse NameSymbolFuseratingCircuit Protected
MODULE 17.5AAMP, Audio, Multi Monitor, Map Lamp, Power Outside Mirror Switch
POWER OUTLET15AConsole Power Outlet
MODULE 610ABCM, PDM, Smart Key Control Module
MODULE 27.5A
IPS Control Module, Instrument Cluster (IND, MICOM), BCM, ATM Shift Lever IND.,
Multifunction Switch (Remote Control), Multi Gauge, Cruise Clutch Pedal Position Switch,
Auto Head Lamp Leveling Device Unit, A/C Control Module, Driver/Passenger Seat Warmer
Module, Stop Lamp Switch, Head Lamp Leveling Device Switch & Actuator LH/RH, Front
Parking Assist Sensor LH/RH, Rear Parking Assist Sensor Side & Center LH/RH
MODULE 57.5ASport Mode Switch (A/T), Key Solenoid
STOP LP15AStop Signal Relay
MODULE 77.5ABlower Relay, Sunroof Control Module, A/C Control Module, Cluster Ionizer (Auto A/C), Electro Chromic Mirror
MODULE 47.5ABCM, PDM, IPS Control Module, Vacuum Switch, E/R Junction Box LH (Vacuum Pump
Relay), Head Lamp Washer Replay
WIPER FRT25AMultiFunction Switch (Wiper), Front Wiper Motor, E/R Junction Box LH (Front Wiper Relay)
START10AE/R Junction Box LH (Start Relay), Ignition Lock Switch, Transaxle Range Switch, ECM
(G6DJ), Burglar Alarm Horn Relay
BLOWER7.5AA/C Control Module
HTD MIRR7.5AA/C Control Module, Driver/Passenger Power Outside Mirror

Maintenance
74
7
Fuse NameSymbolFuseratingCircuit Protected
FUSE
B/ALARM10AICM Relay Box (Burglar Alarm Horn Relay)
DEICER15AFront Deicer Relay
H/LP WASHER20AHead Lamp Washer Relay
VACUUM PUMP15AVacuum Pump Relay (G4KF A/T)
DR LOCK10ASmart Junction Box (Door Lock Relay, Door Unlock Relay)
BRAKE SW10AStop Lamp Switch
HORN15AHorn Relay
DEDICATED DRL10ADEDICATED DRL Relay
B/UP LP10AM/T - Back-Up Lamp Switch
A/T - Rear Combination Lamp LH/RH, Electro Chromic Mirror, A/V &
Navigation Head Unit

Maintenance
76
7
LIGHT BULBS
Use only the bulbs of the specified
wattage.
✽✽ NOTICE
After heavy, driving rain or washing, headlight and taillight lenses could
appear frosty. This condition is caused
by the temperature difference between
the lamp inside and outside. This is sim-
ilar to the condensation on your win-
dows inside your vehicle during the rain
and doesn’t indicate a problem with
your vehicle. If the water leaks into the
lamp bulb circuitry, we recommend thatthe system be checked by an authorized
HYUNDAI dealer.
Headlight, position light, turn sig-
nal light, front fog light bulbreplacement
(1) Front turn signal light
(2) Headlight (High)
(3) Headlight (Low)
(4) Front fog light
(5) Position light/DRL (if equipped)
WARNING - Working on
the lights
Prior to working on the light, firmly
apply the parking brake, ensure
that the ignition switch is turned tothe LOCK position and turn off the
lights to avoid sudden movement
of the vehicle and burning your fin-
gers or receiving an electric shock.
CAUTION
Be sure to replace the burned-out bulb with one of the same wattagerating. Otherwise, it may causedamage to the fuse or electric wiring system.
CAUTION
If you don’t have necessary tools,the correct bulbs and the expertise,
we recommend that you consult anauthorized HYUNDAI dealer. Inmany cases, it is difficult to replace vehicle light bulbs because other
parts of the vehicle must beremoved before you can get to thebulb. This is especially true if you
have to remove the headlightassembly to get to the bulb(s).Removing/installing the headlightassembly can result in damage to
the vehicle.
OBK072026

Maintenance
78
7
Headlight bulb8. Remove the headlight bulb cover by
turning it counterclockwise.
9. Disconnect the headlight bulb socket- connector.
10. Remove the socket from the assem- bly by turning the socket counter-
clockwise until the tabs on the socket
align with the slots on the assembly.
11. Pull the bulb out of the socket.
12. Insert a new bulb into the socket.
13. Install the socket in the assembly by aligning the tabs on the socket with
the slots in the assembly. Push the
socket into the assembly and turn the
socket clockwise.
14. Connect the headlight bulb socket- connector.
15. Install the headlight bulb cover by turning it clockwise.
(Continued)
If a bulb becomes damaged or
cracked, replace it immediately
and carefully dispose of it.
Wear eye protection when chang- ing a bulb. Allow the bulb to cool
down before handling it.
OBK072045OHD076046
WARNING - Halogen bulbs
Halogen bulbs contain pressur-
ized gas that will produce flying
pieces of glass if broken.
Always handle them carefully, and avoid scratches and abra-
sions. If the bulbs are lit, avoid
contact with liquids. Never touchthe glass with bare hands.
Residual oil may cause the bulb
to overheat and burst when lit. A
bulb should be operated onlywhen installed in a headlight.
(Continued)

779
Maintenance
✽✽NOTICE
If the headlight aiming adjustment is
necessary after the headlight assembly is
reinstalled, we recommend that you con-
sult an authorized HYUNDAI dealer.
❋❋ Traffic Change (For Europe)
The low beam light distribution is asym-
metric.
If you go abroad to a country with oppo-
site traffic direction, this asymmetric part
will dazzle oncoming car driver. To pre-
vent dazzle, these headlamps are
designed not to dazzle opposite drivers.
So, you need not change your head-
lamps in a country with opposite trafficdirection.
Turn signal light bulb replacement
8. Remove the socket from the assembly by turning the socket counter clock-
wise until the tabs on the socket align
with the slots on the assembly.
9. Remove the bulb from the socket by pressing it in and rotating it until the
tabs on the bulb align with the slots in
the socket. Pull the bulb out of the
socket.
10. Insert a new bulb by inserting it into the socket and rotating it until it locks
into place.
11. Install the socket into the assembly by aligning the tabs on the socket
with the slots in the assembly. Push
the socket into the assembly and turn
the socket clockwise.
Front fog light bulb replacement
1. Turn the steering wheel fully. (If youwant to replace driver side fog lamp,
turn the steering wheel to the front
passenger side.)
2. Open the hood.
3. Disconnect the negative battery cable.
4. Loosen the retaining bolt on the serv- ice cover. And then pull down the serv-
ice cover.
5. Remove the fog light bulb cover by turning it counter clockwise.
OBK079046OBK072056

Maintenance
80
7
6. Remove the socket from the assembly
by turning the socket counterclockwise
until the tabs on the socket align with
the slots on the assembly
7. Pull the bulb out of the socket.
8. Insert a new bulb into the socket.
9. Install the socket in the assembly by aligning the tabs on the socket with the
slots in the assembly. Push the socket
into the assembly and turn the socket
clockwise.
10. Install the fog light bulb cover by turn- ing it clockwise. And then assemble
the service cover.
Headlight (HID type) bulb, position
(or DRL) lights (LED) replacement
If the light bulb does not operate, we rec-
ommend that you checked an authorized
HYUNDAI dealer.
✽✽ NOTICE
HID lamps have superior performance
vs. halogen bulbs. HID lamps are esti-
mated by the manufacturer to last twice
as long or longer than halogen bulbs
depending on their frequency of use.
They will probably require replacementat some point in the life of the vehicle.
Cycling the headlamps on and off morethan typical use will shorten HID lampslife. HID lamps do not fail in the same
manner as halogen incandescent lamps.
If a headlamp goes out after a period of
operation but will immediately relightwhen the headlamp switch is cycled it islikely the HID lamp needs to be
replaced. HID lighting components are
more complex than conventional halo-
gen bulbs thus have higher replacementcost.
OBK072057
WARNING - HID Headlight
low beam (if equipped)
Do not attempt to replace or
inspect the low beam (XENON bulb)
due to electric shock danger. If the
low beam (XENON bulb) is not
working, we recommend that you
checked an authorized HYUNDAI
dealer.