lock Hyundai Genesis Coupe 2013 Owner's Manual

781
Maintenance
Headlight and front fog light aim- ing
Headlight aiming
1. Inflate the tires to the specified pres-sure and remove any loads from the
vehicle except the driver, spare tire,
and tools.
2. The vehicle should be placed on a flat floor.
3. Draw vertical lines (Vertical lines pass- ing through respective head lamp cen-
ters) and a horizontal line (Horizontalline passing through center of headlamps) on the screen.
4. With the head lamp and battery in nor- mal condition, aim the head lamps so
the brightest portion falls on the hori-
zontal and vertical lines. 5. To aim the low beam left or right, turn
the driver (1) clockwise or counter-
clockwise. To aim the low beam up or
down, turn the driver (2) clockwise or
counterclockwise.
Front fog light aiming
The front fog lamp can be aimed as the same manner of the head lamps aiming.
With the front fog lamps and battery nor-
mal condition, aim the front fog lamps. To
aim the front fog lamp up or down, turn
the driver clockwise or counterclockwise.
OBK072058OBK072059

787
Maintenance
3. Loosen the assembly retaining nuts.
4. Remove the rear combination lightassembly from the body of the vehicle.
Turn signal light
5. Remove the socket from the assemblyby turning the socket counterclockwise
until the tabs on the socket align with
the slots on the assembly.
6. Remove the bulb from the socket by pressing it in and rotating it counter-
clockwise until the tabs on the bulb
align with the slots in the socket. Pull
the bulb out of the socket.
7. Insert a new bulb by inserting it into the socket and rotating it until it locks
into place.
8. Install the socket in the assembly by aligning the tabs on the socket with the
slots in the assembly. Push the socket
into the assembly and turn the socket
clockwise.
Back up or rear fog* 1
light
5. Remove the socket from the assembly
by turning the socket counterclockwise
until the tabs on the socket align with
the slots on the assembly.
6. Remove the bulb by pulling it out.
7. Inset a new bulb by inserting it into the socket.
8. Install the socket in the assembly by aligning the tabs on the socket with the
slots in the assembly. Push the socket
into the assembly and turn the socket
clockwise.
* 1
: if equipped, rear fog light only the driver side
OBK072063
Back up or rear fog Turn signal
OBK072061
OBK072062

Maintenance
88
7
Tail light, Stop and tail light (LED)
(if equipped)
If the light is not operating, we recom-
mend that you checked an authorized
HYUNDAI dealer.
High mounted stop light replace- ment
If the light is not operating, we recom-
mend that you checked an authorized
HYUNDAI dealer.License plate light bulb replace- ment
1. Remove the lens by pressing the tabs.
2. Remove the socket by turning the
soket counter clockwise.
3. Remove the bulb by pulling it straight out.
4. Install a new bulb in the socket and install the socket to the lens.
5. Reinstall the lens securely.
OBK079031
OBK072031
■ Type A
■Type BOFD067030

Specifications & Consumer information
8
8
The tires supplied on your new vehicle
are chosen to provide the best perform-
ance for normal driving.
The tire label located on the driver's side
center pillar gives the tire pressures rec-
ommended for your car.
The engine number is stamped on the
engine block as shown in the drawing.A compressor label informs you the type
of compressor your vehicle is equipped
with such as model, supplier part num-
ber, production number, refrigerant
①
and refrigerant oil ➁.
OBK082003
OBK089004
3.8L
2.0 TCI
OBK082005LODW081001
AIR CONDITIONER COMPRESSOR LABEL
TIRE SPECIFICATION ANDPRESSURE LABEL ENGINE NUMBER