headlight HYUNDAI I20 2014 Owner's Manual

1.$',204/3424-3
(1) Headlight (Low/High) *
2
(2) Low Beam Assist-Static Light
(3) Front Turn Signal Light
(4) Position Light/ Daytime Running Light (DRL)
(5) Front Fog Light (if equipped)
*2: Bi-Function Projection Headlight
II nformation
If the headlight aiming adjustment
is necessary after the headlight
assembly is reinstalled, consult an
authorized HYUNDAI dealer.
The Fog Light aiming adjustment can be done by removing UNDER
COVER. Consult an authorised
HYUNDAI dealer.i(Continued)•
Always handle them carefully,
and avoid scratches and abra-
sions. If the bulbs are lit, avoid
contact w ith liquids. Never touch
the glass with bare hands.
Residual oil may cause the bulb
to overheat and burs t when lit. A
bulb should be operated only
when installed in a headlight.
•
If a bulb becomes damaged or
cracked, replace it immediately
and carefully dispose of it.
•
Wear eye protection when
changing a bulb. Allow the bulb
to cool down before handling it.
Halogen bulbs•
Halogen bulbs contain pressur-
ized gas that will produce flying
pieces of glass if broken.
(Continued)
WARNING
OLMB073042L
OIB077060
■Cross
• Type B

1.$1
,204/3424-3
HHeadlight (Low/High)1. Open the hood.
2. Remove the headlight bulb cover
by turning it counterclockwise.
3. Disconnect the headlight bulb socket-connector. 4. Unsnap the headlight bulb retain-
ing wire by depressing the end
and pushing it upward.
5. Remove the bulb from the head- light assembly.
6. Install a new headlight bulb and snap the headlight bulb retaining
wire into position by aligning the
wire with the groove on the bulb.
7. Connect the headlight bulb socket connector.
8. Install the headlight bulb cover by turning it clockwise.
Information
- Bi-Function projection
headlight
This headlight is bi-function type that
switches the low beam to high or the
high beam to low using solenoid sys-
tem. So, the moving sound may be
heard when the headlight switches the
low beam to high or the high beam to
low and it does not indicate malfunc-
tion of the headlight.
Turn signal light1. Remove the turn signal light bulb cover by turning it counterclock-
wise.
2. Remove the socket from the assembly by turning the socket
counterclockwise until the tabs on
the socket align with the slots on
the assembly.
3. Insert a new bulb by inserting it into the socket and rotating it until
it locks into place.
4. Install the socket in the assembly by aligning the tabs on the socket
with the slots in the assembly.
Push the socket into the assembly
and turn the socket clockwise.
5. Install the turn signal light bulb cover by turning it clockwise.
i
OIB074048
Turn signal light
Parking
(Position) light
Headlight
■ MFR (Multi Focus Reflector) Headlight
OIB075061
Turn signal light
Headlight
■Bi-Function Projection Headlight

# &$$&)
!
10
+'-"-'($-),%**),%#+&*-,")&#($-),
Light BulbBulb type Wattage
Front Headlight (High/Low)
Type A
H460/55
Type B HB360
Position Light Type A
W5W5
Type B LEDLED
Static Bending Light (SBL) Type BH755
Turn signal Light PY2\fW2\f
Fog Light * 88\f27
Daytime Running Light (DRL) * LEDLED
Side Repeater Light (Outside Mirror) WY5W or LED 5 or LED
Rear Tail Light
P2\f/5W5
Tail and Stop Light P2\f/5W2\f/5
Turn Signal Light PY2\fW2\f
Back Up Light 5 Door
W\f6W\f6
Cross PY2\fW2\f
High Mounted Stop Lamp * W5W5
License Plate Lamps W5W5
Interior Map Lamps
FESTOON8
Room Lamp FESTOON8
Luggage Room Lamp * FESTOON\f0
* : If equipped
Type A : MFR (Multi Focus Reflector) Headlamp
Type B : Bi\bFunction Projection Headlamp