steering HYUNDAI I20 2020 Owner's Manual

6-46
Convenient features
Headlamps delay function
(if equipped)
If you place the ignition switch in the
ACC or OFF position with the headlamps
ON, the headlamps (and/or position
lamps) remain on for about 5 minutes.
However, with the engine off if the
driver’s door is opened and closed, the
headlamps (and/or position lamps) are
turned off after 15 seconds.
The headlamps (and/or position lamps)
can be turned off by pressing the lock
button on the remote key or smart
key twice or turning the light switch to
the OFF or AUTO position. However, if
you turn the light switch to the AUTO
position when it is dark outside, the
headlamps will not be turned off.
Headlight leveling device
(if equipped)
OBI3050025OBI3050025
To adjust the headlight beam level
according to the number of the
passengers and loading weight in the
luggage area, turn the beam leveling
switch.
The higher the number of the switch
position, the lower the headlight beam
level. Always keep the headlight beam
at the proper leveling position, or
headlights may dazzle other road users.Listed below are the examples of proper
switch settings. For loading conditions
other than those listed below, adjust the
switch position so that the beam level
may be the nearest as the condition
obtained according to the list.
Loading conditionSwitch position
Driver only 0
Driver +
Front passenger0
Full passengers
(including driver)1
Full passengers
(including driver) +
Maximum permissible
loading2
Driver + Maximum
permissible loading 3
Low Beam Assist-Static light
(if equipped)
While driving a corner, for greater
visibility and safety, either the left or
right side Low Beam Assist-Static light
will turn on automatically. The Low
Beam Assist-Static light will turn on
when one of the following conditions
occur.
• Vehicle speed is less than 10 km/h
(6 mph) and steering wheel angle is
turned approximately 80 degrees with
the low beam on.
• Vehicle speed is between 10 km/h
(6 mph) to 90 km/h (56 mph) and
steering wheel angle is turned
approximately 35 degrees with the low
beam on.
• When the vehicle is in reverse with
one of the conditions above satisfied,
the light opposite to the direction the
steering wheel is turned will turn on.

6-88
Convenient features
NOTICE
• Before entering a place with a low
height clearance, be sure that the
antenna is removed.
• Be sure to remove the antenna before
washing the vehicle in an automatic
car wash or it may be damaged.
• When reinstalling your antenna, it is
important that it is fully tightened
and adjusted to the upright position
to ensure proper reception. But it
could be removed when parking the
vehicle.
NOTICE
Installation of aftermarket antenna may
result in water leakage, wind noise,
rattling & improper radio operation.
We recommend to use the antenna
available with an authorized Hyundai
dealer.
i Information
Some models do not have audio (plastic
blanking cover) system, and will not
supply radio main cable. Thus if you want
to insert Aftermarket audio or OEM
audio to listen radio broadcasting service,
we recommend to use the feeder cable
available with an authorized HYUNDAI
dealer.
Steering wheel audio control
(if equipped)
OBI3050053OBI3050053
The steering wheel audio control
switches are installed for your
convenience.
NOTICE
Do not operate audio remote control
buttons simultaneously.

6-96
Convenient features
System layout – steering wheel
remote control
(Bluetooth® equipped model)
ÃThe system’s actual appearance and
layout may differ depending on the
car model and specification.
(1) MUTE button
• Press to mute or unmute the
system.
• During a call, press to mute or
unmute the microphone.
• While playing media, press to pause
or resume playback. (if equipped)
(2) MODE button
• Press to switch between radio and
media modes.
• If no media is connected, each time
this is pressed, it toggles between
the radio modes (FM X AM X FM).
• Press and hold to turn the system
on or off.
(3) Volume lever
• Push up or down to adjust the
volume.(4) Up/Down lever
• Change the station/track/file.
• While listening to the radio, push
to listen to the previous/next saved
radio station.
• While listening to the radio, push
and hold to search for a station.
• While playing media, push and hold
to rewind or fast forward (except for
the Bluetooth audio mode).
• While playing media push to listen
to the previous/next song.
(5) Call/Answer button
• Press to start connecting a mobile
phone via Bluetooth.
• After a Bluetooth phone connection
is made, press to access your call
history. Press and hold to dial the
most recent phone number. When
a call comes in, press to answer the
call.
• During a call, press to switch
between the active call and the held
call. Press and hold to switch the
call between the system and the
mobile phone.
• In 3-way call, swaps between calls.
(6) Call end button
• When a call comes in, reject the call.
• During a call, end the call.

6-101
06
Changing the radio mode
1. On the control panel, press the
[AUDIO] button.
2. When the mode selection window
displays, turn the [TUNE] knob to
select the desired radio mode and
then press the knob.
• Each time you press the [MODE]
button on the steering wheel, the
radio mode switches to FM X AM
in order.
NOTICE
When the Mode popup is not selected
in [MENU/CLOCK] X Mode popup, press
the [AUDIO] button on the control panel
to change the radio mode.
Each time you press the [AUDIO] button
on the control panel, the radio mode
switches to FM X AM in order.
Scanning for available radio
stations
You can listen to each radio station for
a few seconds to test the reception and
select the one you want.
1. From the radio screen, press the
[MENU/CLOCK] button on the control
panel.
2. When the option selection window
displays, turn the [TUNE] knob to
select Scan, and then press the knob.
• The system searches for radio
stations with strong radio signals
and plays each radio station for
about five seconds.
3. When you find the radio station you
want to listen to, press the [TUNE]
knob.
• You can continue listening to the
selected station.
•
Searching for radio stations
To search for the previous or next
available radio station, press the
[< SEEK] button / [TRACK >] button on
the control panel.
• You can also press and hold the
[< SEEK] button / [TRACK >] button
to search for frequencies quickly.
When you release the button, a radio
station with a strong signal is selected
automatically.
If you know the exact frequency of the
radio station you want to listen to, turn
the [TUNE] knob on the control panel to
change the frequency.

6-102
Convenient features
Saving radio stations
You can save your favourite radio stations
and listen to them by selecting them
from the preset list.
Saving the current radio station
While listening to the radio, press and
hold the desired number button on the
control panel.
• The radio station you are listening to
will be added to the selected number.
• To save the next page of the preset
list, press the [FAV] button.
NOTICE
• You can save up to 12 radio stations
in each mode.
• If a station is already saved to the
selected preset number, the station
will be replaced by the station you
are listening to.
Using the auto save function
You can search for radio stations in your
area where there is a strong signal. The
results of your search can be saved to the
preset list automatically.
1. From the radio screen, press the
[MENU/CLOCK] button on the control
panel.
2. When the option selection window
displays, turn the [TUNE] knob to
select Autostore, and then press the
knob.
Listening to saved radio stations
FM/AM Mode
1. Confirm the preset number for the
radio station you want to listen to.
• To view the next page of the preset
list, press the [FAV] button.
2. On the control panel, press the
desired number button.
• Alternatively, Push the Up/Down
lever on the steering wheel to
change the station.

6-103
06
0(',$3/$<(5
Using the media player
You can play music stored in various
media storage devices, such as USB
storage devices, smartphones.
1. Connect a device to the USB port in
your vehicle.
• Playback may start immediately
depending on the device that you
connect to the system.
2. On the control panel, press the
[AUDIO] button.
3. When the mode selection window
displays, turn the [TUNE] knob to
select the desired mode and then
press the knob.
NOTICE
• To start the media player, press the
[AUDIO] button on the control panel.
• You can also change the mode by
press the [MODE] button repeatedly
on the steering wheel.
• Make sure to connect or disconnect
external USB devices with the system
power turned off.
• When the Mode popup is not
selected in [MENU/CLOCK] X Mode
popup, press the [AUDIO] button
on the control panel to change the
media player.
Each time you press the [AUDIO]
button on the control panel, the
media mode switches to USB X
Bluetooth audio in order.
• Depending on vehicle models and
specifications, available buttons or
the appearance and layout of the
USB port in your vehicle may vary.• Do not connect a smartphone or
an MP3 device to the system via
multiple methods such as USB and
Bluetooth simultaneously. Doing
so may cause a distorted noise or a
system malfunction.
• When the equaliser function of the
connected device and Equaliser
settings of the system are both
activated, the effects may interfere
with each other and may lead to
sound degradation or distortion.
Deactivate the device’s equaliser
function if possible.
Using the USB mode
You can play media files stored in
portable devices, such as USB storage
devices and MP3 players. Check
compatible USB storage devices and
file specifications before using the USB
mode.
Connect your USB device to the USB port
in the vehicle.
• Playback starts immediately.
• Press the [AUDIO] button on the
control panel to display the mode
selection window, turn the [TUNE]
knob to select USB and then press the
knob.

6-104
Convenient features
(1) Current file number and total number
of files
(2) Playback time
(3) Information about the song currently
playing
Press the [MENU/CLOCK] button on the
control panel to access the following
menu options:
• List: Access the file list.
• Folder list: Access the folder list.
• Information: Display information
about the song currently playing.
• Sound settings: You can change
the settings related to sounds, such
as location where sound will be
concentrated and the output level for
each range.
-Position: Select a location where
sound will be concentrated in the
vehicle. Select Fader or Balance,
turn the [TUNE] knob to select the
desired position, and then press the
knob. To set sound to be centred in
the vehicle, select Centre.
-Equaliser: Adjust the output level
for each sound tone mode.
-Sound experience: Select the
location where sound is focused
in the vehicle between the driver’s
seat and all other seats.
-Speed dependent vol.: Set the
volume to be adjusted automatically
according to your driving speed.
NOTICE
• Depending on vehicle models or
specifications, available options may
vary.
• Depending on the system or
amplifier specifications applied to
your vehicle, available options may
vary.
• Song information: Select information
such as Folder/File or Artist/Title/
Album to display when playing MP3
files.
• Mode popup: Set to display mode
selection window when the [AUDIO]
button is pressed on the control panel.
• Bluetooth remote lock: Even if
Bluetooth remote control application
is connected, if Set Bluetooth remote
lock is enabled. System cannot be
operated via smart phone application.
• Date/Time: You can change the
date and time that are shown on the
system display.
-Set date: Set date to display on the
system display.
-Set time: Set time to display on the
system display.
-Time format: Select to display time
in the 12 hour format or the 24 hour
format.
-Display (Power Off): Set to display
the clock when the system power
is off.
• Language: You can change the
display language.
Rewinding/Fast forwarding
On the control panel, press and hold the
[< SEEK] button / [TRACK >] button.
• You can also push and hold the Up/
down lever on the steering wheel.

6-105
06
Restarting the current playback
On the control panel after the song has
played for 2 seconds, press the [< SEEK]
button.
• You can also push the Up lever on the
steering wheel.
Playing the previous or next song
To play the previous song on the control
panel within the first 2 seconds of the
current song, press the [< SEEK] button.
To play the next song, press the [TRACK >]
button on the control panel.
• If more than 2 seconds of playback
have elapsed, press the [< SEEK]
button on the control panel twice to
play the previous song.
• You can also push the Up/down lever
on the steering wheel.
NOTICE
Press the [MENU/CLOCK] button on
the control panel to display the mode
selection window, turn the [TUNE] knob
to find the desired song and press the
knob to play the file.
Playing repeatedly
On the control panel, press the [1 RPT]
button. The corresponding mode icon
will be displayed on the screen and the
playing song will be repeated.
Playing in random order
On the control panel, press the
[2 SHFL] button. The shuffle play mode is
activated or deactivated each time you
press it. When you activate the shuffle
mode, the corresponding mode icon will
be displayed on the screen. When shuffle
is active, the available songs will be
played randomly.
NOTICE
Depending on the connected Bluetooth
device or mobile phone, repeat &
shuffle order features may not be
supported.
Searching folders
1. On the control panel, press the
[MENU/CLOCK] button.
2. When the option selection window
displays, turn the [TUNE] knob to
select the Folder list and then press
the knob.
3. Navigate to the desired folder in the
Folder list and then press the [TUNE]
knob.
• The first song in the selected folder
will be played.
i Information
• Start the engine of your vehicle before
connecting a USB device to your
system. Starting the engine with a USB
device connected to the system may
damage the USB device.
• Be careful of static electricity when
connecting or disconnecting a USB
device. A static discharge may cause a
system malfunction.
• Be careful not to let your body or
external objects contact the USB port.
Doing so may cause an accident or a
system malfunction.
• Do not connect and disconnect a USB
connector repeatedly in a short time.
Doing so may cause an error in the
device or a system malfunction.
• Do not use a USB device for purposes
other than playing files. Using USB
accessories for charging or heating may
cause poor performance or a system
malfunction.

6-107
06
%/8(7227+
Connecting Bluetooth devices
Bluetooth is a short-range wireless
networking technology. Via Bluetooth,
you can connect nearby mobile
devices wirelessly to send and receive
data between connected devices.
This enables you to use your devices
effectively.
To use Bluetooth, you must first connect
a Bluetooth-enabled device to your
system, such as a mobile phone or an
MP3 player. Ensure that the device you
want to connect supports Bluetooth.
WARNING
Park your vehicle in a safe location
before connecting Bluetooth devices.
Distracted driving can cause a traffic
accident and lead to personal injury or
death.
NOTICE
• On your system, you can use only
Bluetooth Handsfree and Audio
features. Connect a mobile device
that supports both features.
• Some Bluetooth devices may cause
malfunctions to the audio system
or make interference noises. In this
case, storing the device in a different
location may resolve the problem.
• Depending on the connected
Bluetooth device or mobile
phone, some functions may not be
supported.
• If the system is not stable due
to a vehicle-Bluetooth device
communication error, delete the
paired devices and connect the
Bluetooth devices again.• If Bluetooth connection is not stable,
follow these steps to try again.
1. Deactivate Bluetooth and
reactivate it on the device. Then,
reconnect the device.
2. Turn the device off and on. Then,
reconnect it.
3. Remove the battery from the
device and reinstall it. Then, turn
the device on and reconnect it.
4. Unregister the Bluetooth pairing
on both the system and the device
and then re-register and connect
them.
• The Bluetooth connection is
unavailable when the device’s
Bluetooth function is turned off.
Be sure to turn on the device’s
Bluetooth function.
Pairing devices with your system
For Bluetooth connections, first pair your
device with your system to add it to the
system’s list of Bluetooth devices. You
can register up to five devices.
1. From the control panel, press the
[PHONE] button, and then select
Phone settings X Add new device.
• If you are pairing a device with your
system for the first time, you can
also press the Call/Answer button
on the steering wheel.
2. On the Bluetooth device you want to
connect, activate Bluetooth, search
for your vehicle’s system, and then
select it.
• Check the system’s Bluetooth
name, which is displayed in the new
registration pop-up window on the
system screen.

6-108
Convenient features
3. Enter or confirm the passkey to
confirm the connection.
• If the passkey input screen is
displayed on the Bluetooth device
screen, enter the passkey ‘0000’
which is displayed on the system
screen.
• If the 6-digit passkey is displayed
on the Bluetooth device screen,
ensure that the Bluetooth passkey
displayed on the Bluetooth device
is the same as the passkey on the
system screen and confirm the
connection from the device.
NOTICE
• The screen image in this manual is an
example. Check your system screen
for the exact vehicle name and
Bluetooth device name.
• The default passkey is ‘0000’.
• It may take a while for the system
to connect with the device after
you permit the system to access the
device. When a connection is made,
the Bluetooth status icon appears at
the top of the screen.
• You can change the permission
settings via the mobile phone’s
Bluetooth settings menu. For more
information, refer to your mobile
phone’s user guide.
• To register a new device, repeat
steps 1 to 3.
• If you use the automatic Bluetooth
connection function, a call may be
switched to the vehicle’s Handsfree
when you are taking on the phone
near the vehicle while the vehicle’s
engine is on. If you do not want the
system to connect with the device
automatically, deactivate Bluetooth
on your device.
• When a device is connected to the
system via Bluetooth, the device’s
battery may discharge faster.
Connecting a paired device
To use a Bluetooth device on your
system, connect the paired device to the
system. Your system can connect with
only one device at a time.
1. From the control panel, press the
[PHONE] button, and then select
Phone settings X Paired devices.
• If there is no connected device,
press the Call/Answer button on the
steering wheel.
2. Turn the [TUNE] knob to select the
device to connect, and then press the
knob.
• If another device is already
connected to your system,
disconnect it. Select the connected
device to disconnect.
NOTICE
• If a connection ends because a
device is out of the connection
range or a device error occurs,
the connection will be restored
automatically when the device
enters the connection range or when
the error is cleared.
• Depending on auto connection
priority, connection to a device may
take time.