warning HYUNDAI I20 2023 Owners Manual
[x] Cancel search | Manufacturer: HYUNDAI, Model Year: 2023, Model line: I20, Model: HYUNDAI I20 2023Pages: 649, PDF Size: 12.35 MB
Page 532 of 649
8-17
08
Changing tyres
WARNING
A vehicle can slip or roll off of a jack
causing serious injury or death to you
or those nearby. Take the following
safety precautions:
[ Do not get under a vehicle that is
supported by a jack.
[ NEVER attempt to change a tyre in
the lane of traffic. ALWAYS move the
vehicle completely off the road on
level, firm ground away from traffic
before trying to change a tyre. If you
cannot find a level, firm place off
the road, call a towing service for
assistance.
[ Be sure to use the jack provided with
the vehicle.
[ ALWAYS place the jack on the
designated jacking positions on the
vehicle and NEVER on the bumpers
or any other part of the vehicle for
jacking support.
[ Do not start or run the engine whilst
the vehicle is on the jack.
[ Do not allow anyone to remain in the
vehicle whilst it is on the jack.
[ Keep children away from the road
and the vehicle.
Follow these steps to change your
vehicle’s tyre:
1. Park on a level, firm surface.
2. Move the shift lever into P (Park, for
automatic transmission/dual clutch
transmission vehicle) or neutral
(for manual transmission vehicle),
apply the parking brake, and place
the ignition switch in the LOCK/OFF
position.
3. Press the hazard warning flasher
button.
4. Remove the wheel lug nut wrench,
jack, jack handle, and spare tyre from
the vehicle.
OBC3080005
[A] : Block
5. Block both the front and rear of the
tyre diagonally opposite of the tyre
you are changing.
OBC3080006
6. Loosen the wheel lug nuts
counterclockwise one turn each in
the order shown above, but do not
remove any lug nuts until the tyre has
been raised off of the ground.
Page 534 of 649
8-19
08
If you have a tyre gauge, check the tyre
pressure (see “Tyres and Wheels” in
chapter 2 for tyre pressure instructions.).
If the pressure is lower or higher than
recommended, drive slowly to the
nearest service station and adjust it to
the recommended pressure. Always
reinstall the valve cap after checking
or adjusting tyre pressure. If the cap
is not replaced, air may leak from the
tyre. If you lose a valve cap, buy another
and install it as soon as possible. After
changing tyres, secure the flat tyre and
return the jack and tools to their proper
storage locations.
NOTICE
[ & K H F N W K H W \ U H S U H V V X U H D V V R R Q
as possible after installing a spare
tyre. Adjust it to the recommended
pressure.
[ & K H F N D Q G W L J K W H Q W K H Z K H H O O X J Q X W V
after driving over 50 km if tyres are
replaced. Re-check the tyre wheel
lug nuts after driving over 1,000 km.
CAUTION
Your vehicle has metric threads on
the studs and lug nuts. Make certain
during tyre changing that the same
nuts that were removed are reinstalled.
If you have to replace your lug nuts
make sure they have metric threads to
avoid damaging the studs and ensure
the wheel is properly secured to the
hub. We recommend that you consult
a HYUNDAI authorised repairer for
assistance.
If any of the equipment such as the jack,
lug nuts, studs, or other equipment is
damaged or in poor condition, do not
attempt to change the tyre and call for
assistance.
Use of compact spare tyres
(if equipped)
Compact spare tyres are designed for
emergency use only. Drive carefully
on the compact spare tyre and always
follow the safety precautions.
WARNING
To prevent compact spare tyre failure
and loss of control possibly resulting in
an accident:
[ 8 V H W K H F R P S D F W V S D U H W \ U H R Q O \ L Q D Q
emergency.
[ 1 ( 9 ( 5 R S H U D W H \ R X U Y H K L F O H R Y H U
mph (80 km/h).
[ ' R Q R W H [ F H H G W K H Y H K L F O HT V
maximum load rating or the load
carrying capacity shown on the
sidewall of the compact spare tyre.
[ ' R Q R W X V H W K H F R P S D F W V S D U H W \ U H
continuously. Repair or replace the
original tyre as soon as possible to
avoid failure of the compact spare
tyre.
Page 544 of 649
8-29
08
WARNING
Expired sealant
Do not use the Tyre sealant after
the sealant has expired (i.e. pasted
the expiration date on the sealant
container). This can increase the risk of
tyre failure.
WARNING
Sealant
[ Keep out of reach of children.
[ Avoid contact with eyes.
[ Do not swallow.
Strictly follow the specified sequence,
otherwise the sealant may escape under
high pressure.
WARNING
To inflate tire pressure only (not with
flat tire),
Follow the instruction “Checking the
tire inflation pressure” provided in this
chapter.
Using the Tyre Mobility Kit
CAUTION
Detach the speed restriction label (1)
from the sealant bottle (2), and place
it in a highly visible place inside the
vehicle such as on the steering wheel to
remind the driver not to drive too fast.
OLMF064103
1. Shake the sealant bottle.
ODN8079019
2. Screw connection hose (10) onto the
connector of the sealant bottle.
3. Ensure that button (9) on the
compressor is not pressed.
4. Unscrew the valve cap from the valve
of the defective wheel and screw
filling hose (3) of the sealant bottle
onto the valve.
Page 546 of 649
8-31
08
WARNING
Carbon monoxide
Do not leave your vehicle running in
a poorly ventilated area for extended
periods of time.
Carbon monoxide poisoning and
suffocation can occur.
Distributing the sealant
11. Immediately drive approximately
4~6miles (7~10km or, about 10 mins)
to evenly distribute the sealant in the
tyre.
Do not exceed a speed of 50 mph (80
km/h). If possible, do not fall below a
speed of 12 mph (20 km/h).
Whilst driving, if you experience any
unusual vibration, ride disturbance or
noise, reduce your speed and drive with
caution until you can safely pull off the
vehicle on the side of the road.
Call for road side service or towing.
When you use the Tyre Mobility Kit, the
tyre pressure valve and wheel may be
damaged by sealant, remove the sealant
stained. We recommend that the tyre
pressure valve and wheel be inspected
by an authorized HYUNDAI dealer.
Checking the tyre inflation
pressure
1. After driving approximately 4 ~6miles
(7~10km or about 10min), stop at a
safety location.
2. Connect connection hose (10) of the
compressor directly to the tyre valve.
3. Plug the compressor power cord into
the vehicle power outlet.
4. Adjust the tyre inflation pressure to
the recommended tyre inflation.
With the ignition switched on, proceed
as follows.
- To increase the inflation pressure :
Switch on the compressor, position
I. To check the current inflation
pressure setting, briefly switch off
the compressor.
i Information
The pressure gauge may show higher than
actual reading when the compressor is
running. To get an accurate tyre pressure,
the compressor needs to be turned off.
NOTICE
- Tyre pressure valve
We recommend that you use the
sealant of tyre mobility kit from a
HYUNDAI authorised repairer. The
sealant on the tyre pressure valve and
wheel should be removed when you
replace the tyre with a new one and
we recommend that the tyre pressure
valve be inspected by an authorized
HYUNDAI dealer.
Page 554 of 649
8-39
08
It will also be triggered automatically
when the vehicle is equipped with a TPS
system which does not function in the
event of a severe accident.
The 112-based eCall in-vehicle system
can also be triggered manually, if
needed. Instructions for manual
activation of the system: refer to this
section.
In the event of a critical system failure
that would disable the 112-based eCall
in-vehicle system, the following warning
will be given to the occupants of the
vehicle: refer to this section.
Information on data processing
Any processing of personal data
through the 112-based eCall in-vehicle
system shall comply with the personal
data protection rules provided for in
Directives 95/46/EC (1) and 2002/58/
EC (2) of the European Parliament and
of the Council, and in particular, shall
be based on the necessity to protect
the vital interests of the individuals in
accordance with Article 7(d) of Directive
95/46/EC (3).
Processing of such data is strictly
limited to the purpose of handling the
emergency eCall to the single European
emergency number 112.
Types of data and its recipients
The 112-based eCall in-vehicle system
may collect and process only the
following data:
- Vehicle Identification Number
- Vehicle type (passenger vehicle or light
commercial vehicle)
- Vehicle propulsion storage type
(petrol/diesel/CNG/LPG/electric/
hydrogen)
- Vehicle recent locations and direction
of travel
- Log file of the automatic activation of
the system and its timestamp
- Any additional data (if applicable): Not
applicable
Recipients of data processed by the 112-
based eCall in-vehicle system are the
relevant public safety answering points
designated by the respective public
authorities of the country on which
territory they are located, to first receive
and handle eCalls to the single European
emergency number 112. Additional
information (if available): Not applicable
Page 559 of 649
8-44
Emergency situations
WARNING
Emergency power supply of the Pan-
European eCall system from the battery
[ 7 K H 3 D Q ( X U R S H D Q H & D O O V \ V W H P
battery supplies power during 1 hour
in case the main power source of the
vehicle is cut off due to the collision
during the emergency situations.
[ 7 K H 3 D Q ( X U R S H D Q H & D O O V \ V W H P
battery should be replaced every 3
years. For more information, refer to
“Maintenance Schedule” in chapter
9.
LED illumination in red (system
malfunction)
If the red LED illuminates in normal
driving conditions, this can indicate
malfunction of the Pan-European
eCall system. We recommend that you
have the Pan-European eCall system
checked by a HYUNDAI authorised
repairer as soon as possible. Otherwise
correct operation of the Pan-European
eCall system device, installed in your
vehicle is not guaranteed. Owner
of the vehicle incurs liability for
consequences, occurred as a result
of nonobservance of conditions,
mentioned above. Arbitrary Removal or Modification
The Pan-European eCall system calls
emergency services for assistance.
Thus, any arbitrary removal or changes
to the Pan-European eCall system
settings may affect your driving safety.
Also, it may even make an erroneous
emergency call to the Public Safety
Answering Point (PSAP). Thereby, we
kindly ask you not to make any changes
by yourself or by the third parties in the
settings of the equipment of the Pan-
European eCall system, installed in your
vehicle.
Page 566 of 649
9-7
09
WARNING
Performing maintenance work on a
vehicle can be dangerous. If you lack
sufficient knowledge and experience
or the proper tools and equipment
to do the work, we recommend that
the system be serviced by a HYUNDAI
authorised repairer. ALWAYS follow
these precautions for performing
maintenance work:
[ 3 D U N \ R X U Y H K L F O H R Q O H Y H O J U R X Q G
move the shift lever into the P (Park,
for automatic transmission/dual
clutch transmission vehicle) position,
apply the parking brake, and place
the ignition switch in the LOCK/OFF
position.
[ % O R F N W K H W \ U H V I U R Q W D Q G E D F N W R
prevent the vehicle from moving.
Remove loose clothing or jewellery
that can become entangled in
moving parts.
[ , I \ R X P X V W U X Q W K H H Q J L Q H G X U L Q J
maintenance, do so out doors or in an
area with plenty of ventilation.
[ . H H S I O D P H V V S D U N V R U V P R N L Q J
materials away from the battery and
fuel-related parts.The following lists are vehicle checks
and inspections that should be
performed by the owner or a HYUNDAI
authorised repairer at the frequencies
indicated to help ensure safe,
dependable operation of your vehicle.
Any adverse conditions should be
brought to the attention of your dealer
as soon as possible.
These Owner Maintenance vehicle
checks are generally not covered by
warranties and you may be charged for
labour, parts and lubricants used.
Owner maintenance schedule
When you stop for fuel:
[ Check the coolant level in the engine
coolant reservoir.
[ Check the windscreen washer fluid
level.
[ Check for low or under-inflated tyres.
[ Check the radiator and condenser.
Check if the front of the radiator and
condenser are clean and not blocked
with leaves, dirt or insects, etc.
If any of the above parts are extremely
dirty or you are not sure of their
condition, we recommend that
you contact a HYUNDAI authorised
repairer.
WARNING
% H F D U H I X O Z K H Q F K H F N L Q J \ R X U H Q J L Q H
coolant level when the engine is hot.
This may result in coolant being blown
out of the opening and cause serious
burns and other injuries.
OWNER MAINTENANCE
Page 567 of 649
9-8
Maintenance
Whilst operating your vehicle:
[ Note any changes in the sound of the
exhaust or any smell of exhaust fumes
in the vehicle.
[ Check for vibrations in the steering
wheel. Notice if there is any increased
steering effort or looseness in the
steering wheel, or change in its
straight-ahead position.
[ Notice if your vehicle constantly turns
slightly or “pulls” to one side when
travelling on smooth, level road.
[ When stopping, listen and check for
unusual sounds, pulling to one side,
increased brake pedal travel or “hard-
to-push” brake pedal.
[ If any slipping or changes in the
operation of your transmission occurs,
check the transmission fluid level.
[ Check the parking brake.
[ Check for fluid leaks under your
vehicle (water dripping from the air
conditioning system during or after
use is normal).
At least monthly:
[ Check coolant level in the engine
coolant reservoir.
[ Check the operation of all exterior
lights, including the stoplights, turn
signals and hazard warning flashers.
[ Check the inflation pressures of all
tyres including the spare for tyres that
are worn, show uneven wear, or are
damaged.
[ Check for loose wheel lug nuts.
At least twice a year:
(i.e., every Spring and Autumn)
[ Check radiator, heater and air
conditioning hoses for leaks or
damage.
[ Check windscreen washer spray and
wiper operation. Clean wiper blades
with a clean cloth dampened with
washer fluid.
[ Check headlight alignment.
[ Check muffler, exhaust pipes, shields
and clamps.
[ Check the seat belts for wear and
function.
At least once a year:
[ Clean body and door drain holes.
[ Lubricate door hinges and bonnet
hinges.
[ Lubricate door and bonnet locks and
latches.
[ Lubricate door rubber weather strips.
[ Lubricate door checker
[ Check the air conditioning system.
[ Inspect and lubricate automatic
transmission linkage and controls.
[ Clean the battery and terminals.
[ Check the brake fluid level.
Page 570 of 649
9-11
09
Vacuum crankcase ventilation
hoses (if equipped)
Inspect the surface of hoses for
evidence of heat and/or mechanical
damage. Hard and brittle rubber,
cracking, tears, cuts, abrasions, and
excessive swelling indicate deterioration.
Particular attention should be paid to
examine those hose surfaces nearest to
high heat sources, such as the exhaust
manifold.
Inspect the hose routing to assure that
the hoses do not come in contact with
any heat source, sharp edges or moving
component which might cause heat
damage or mechanical wear. Inspect
all hose connections, such as clamps
and couplings, to make sure they are
secure, and that no leaks are present.
Hoses should be replaced immediately if
there is any evidence of deterioration or
damage.
Air cleaner filter
We recommend that the air cleaner filter
be replaced by a HYUNDAI authorised
repairer.
Spark plugs
(for petrol engine)
Make sure to install new spark plugs of
the correct heat range.
When assembling parts, be sure to
wipe out foreign substances inside
and outside of the boot bottom of the
ignition coil and the insulator of the
spark plug with a soft cloth to prevent
contamination of the spark plug
insulator.
WARNING
Do not disconnect and inspect spark
plugs when the engine is hot. You may
burn yourself.
Cooling system
Check the cooling system parts, such
as radiator, coolant reservoir, hoses and
connections for leakage and damage.
Replace any damaged parts.
Engine coolant
The coolant should be changed at the
intervals specified in the maintenance
schedule.
Manual transmission fluid/iMT
system actuator fluid
(if equipped)
Inspect the Manual transmission fluid/
iMT system actuator fluid according to
the maintenance schedule.
Automatic transmission fluid
(if equipped)
Automatic transmission fluid should
not be checked under normal usage
conditions.
We recommend that the automatic
transmission fluid is changed by a
HYUNDAI authorised repairer according
to the maintenance schedule.
i Information
$ X W R P D W L F W U D Q V P L V V L R Q I O X L G F R O R X U L V U H G
Z K H Q Q H Z
$ V W K H Y H K L F O H L V G U L Y H Q W K H D X W R P D W L F
W U D Q V P L V V L R Q I O X L G Z L O O E H J L Q W R O R R N
G D U N H U
7 K L V L V D Q R U P D O F R Q G L W L R Q , W G R H V Q R W
Q H H G W R E H U H S O D F H G E D V H G R Q W K H F R O R X U
F K D Q J H
Page 574 of 649
9-15
09
Checking the engine oil and
filter
[ We recommend that the engine oil
and filter be replaced by a HYUNDAI
authorised repairer.
[ If the maintenance schedule to
replace engine oil is exceeded,
the engine oil performance may
deteriorate, and the engine condition
may be affected. Therefore, replace
the engine oil according to the
maintenance schedule.
[ To keep the engine in optimal
condition, use the recommended
engine oil and filter. If the
recommended engine oil and filter are
not used replace it according to the
maintenance schedule under severe
usage conditions.
[ The purpose of the maintenance
schedule for engine oil replacement
is to prevent oil deterioration and it is
irrelevant to oil consumption. Check
and refill engine oil regularly.
WARNING
Used engine oil may cause irritation or
cancer of the skin if left in contact with
the skin for prolonged periods of time.
Used engine oil contains chemicals
that have caused cancer in laboratory
animals. Always protect your skin
by washing your hands thoroughly
with soap and warm water as soon as
possible after handling used oil.
i Information
: K H Q W K H R L O S U H V V X U H L V O R Z G X H W R
L Q V X I I L F L H Q W H Q J L Q H R L O W K H ( Q J L Q H 2 L O
3 U H V V X U H
Z D U Q L Q J O L J K W Z L O O
L O O X P L Q D W H , Q D G G L W L R Q W K H H Q K D Q F H G
H Q J L Q H S U R W H F W L R Q V \ V W H P Z K L F K O L P L W V
W K H H Q J L Q H