Steering HYUNDAI I20 2023 Workshop Manual
[x] Cancel search | Manufacturer: HYUNDAI, Model Year: 2023, Model line: I20, Model: HYUNDAI I20 2023Pages: 649, PDF Size: 12.35 MB
Page 331 of 649
6-58
Driving your vehicle
Hazardous driving conditions
When hazardous driving elements are
encountered such as water, snow,
ice, mud and sand, take the following
precautions:
[ Drive cautiously and maintain a longer
braking distance.
[ Avoid abrupt braking or steering.
[ When your vehicle is stuck in snow,
mud, or sand, use the second
gear. Accelerate slowly to avoid
unnecessary wheel spin.
[ Put sand, rock salt, tyre chains or
other non-slip materials under the
wheels to provide additional traction
whilst the vehicle becomes stuck in
ice, snow, or mud.
WARNING
Downshifting with an Automatic
transmission, whilst driving on slippery
surfaces can cause an accident. The
sudden change in tyre speed could
cause the tyres to skid. Be careful when
downshifting on slippery surfaces.
Rocking the vehicle
If it is necessary to rock the vehicle to
free it from snow, sand, or mud, first
turn the steering wheel right and left to
clear the area around your front wheels.
Then, shift back and forth between the
1st gear and R (Reverse, for manual
transmission vehicle) or R (Reverse)
and a forward gear (for Automatic
transmission vehicle/Dual clutch
transmission vehicle).
Try to avoid spinning the wheels, and do
not race the engine.
To prevent transmission wear, wait until
the wheels stop spinning before shifting
gears. Release the accelerator pedal
whilst shifting, and press lightly on the
accelerator pedal whilst the transmission
is in gear. Slowly spinning the wheels in
forward and reverse directions causes
a rocking motion that may free the
vehicle.
WARNING
If the vehicle is stuck and excessive
wheel spin occurs, the temperature
in the tyres can increase very quickly.
If the tyres become damaged, a tyre
blow out or tyre explosion can occur.
This condition is dangerous - you and
others may be injured. Do not attempt
this procedure if people or objects are
anywhere near the vehicle.
If you attempt to free the vehicle, the
vehicle can overheat quickly, possibly
causing an engine compartment fire or
other damages. Try to avoid spinning
the wheels as much as possible to
prevent overheating of either the tyres
or the engine. DO NOT allow the vehicle
to spin the wheels above 35 mph (56
km/h).
i Information
7 K H ( 6 & V \ V W H P L I H T X L S S H G P X V W E H
W X U Q H G 2 ) ) E H I R U H U R F N L Q J W K H Y H K L F O H
6 3 ( & , $ / ' 5 , 9 , 1 * & 2 1 ' , 7 , 2 1 6
Page 337 of 649
6-64
Driving your vehicle
Check spark plugs and ignition system
Inspect the spark plugs, as specified
in the chapter 9. If necessary, replace
them. Also check all ignition wirings and
components for any cracks, wear-out,
and damage.
To prevent locks from freezing
To prevent the locks from being frozen,
spray approved de-icing fluid or glycerin
into key holes. When a lock opening is
already covered with ice, spray approved
de-icing fluid over the ice to remove it.
When an internal part of a lock freezes,
try to thaw it with a heated key. Carefully
use the heated key to avoid an injury.
Use approved window washer anti-
freeze solution in system
To prevent the window washer from
being frozen, add authorised window
washer anti-freeze solution, as specified
on the window washer container.
Window washer anti-freeze solution is
available from a HYUNDAI authorised
repairer, and most vehicle accessory
outlets. Do not use engine coolant or
other types of anti-freeze solution to
prevent any damage to the vehicle paint.
Do not let your parking brake freeze
Under some conditions your parking
brake can freeze in the engaged
position.
This is most likely to happen when
there is an accumulation of snow or
ice around or near the rear brakes or if
the brakes are wet. When there is the
risk that your parking brake may freeze,
temporarily apply it with the shift lever
in N (for Automatic Transmission/Dual
clutch transmission) or in the 1st gear or
reverse gear (for Manual transmission).
Also, block the rear wheels in advance,
so the vehicle may not roll. Then, release
the parking brake.Do not let ice and snow accumulate
underneath
Under some conditions, snow and ice
can build up under the fenders and
interfere with the steering. When driving
in such conditions during the severe
winter, you should check underneath
the vehicle on a regular basis, to ensure
that the front wheels and the steering
components is unblocked.
Carry emergency equipment
In accordance with weather conditions,
you should carry appropriate emergency
equipment, whilst driving. Some of the
items you may want to carry include tyre
chains, tow straps or chains, flashlight,
emergency flares, sand, shovel, jumper
cables, window scraper, gloves, ground
cloth, coveralls, blanket, etc.
Do not place objects or materials in the
engine compartment
Putting objects or materials in the
engine compartment may cause an
engine failure or combustion, because
they may block the engine cooling.
Such damage will not be covered by the
manufacturer’s warranty.
Page 343 of 649
6-70
Driving your vehicle
Driving with a trailer
Towing a trailer requires a certain
amount of experience. Before setting
out for the open road, you must get to
know your trailer. Acquaint yourself with
the feel of handling and braking with the
added weight of the trailer. And always
keep in mind that the vehicle you are
driving is now longer and not nearly as
responsive as your vehicle is by itself.
Before you start, check the trailer towbar
and platform, safety chains, electrical
connector(s), lights, tyres and brakes.
During your trip, occasionally check
to be sure that the load is secure, and
that the lights and trailer brakes are still
working.
Distance
Stay at least twice as far behind the
vehicle ahead as you would when driving
your vehicle without a trailer. This can
help you avoid situations that require
heavy braking and sudden turns.
Passing
You will need more passing distance up
ahead when you’re towing a trailer. And,
because of the increased vehicle length,
you’ll need to go much farther beyond
the passed vehicle before you can return
to your lane.
Backing up
Hold the bottom of the steering wheel
with one hand. Then, to move the trailer
to the left, move your hand to the left.
To move the trailer to the right, move
your hand to the right. Always back up
slowly and, if possible, have someone
guide you.
Making turns
When you’re turning with a trailer, make
wider turns than normal. Do this so your
trailer won’t strike soft shoulders, kerbs,
road signs, trees, or other objects. Avoid
jerky or sudden manoeuvres. Signal well
in advance.
Turn signals
When you tow a trailer, your vehicle has
to have a different turn signal flasher and
extra wiring. The green arrows on your
instrument panel will flash whenever you
signal a turn or lane change. Properly
connected, the trailer lights will also
flash to alert other drivers you’re about
to turn, change lanes, or stop.
When towing a trailer, the green arrows
on your instrument panel will flash for
turns even if the bulbs on the trailer
are burned out. Thus, you may think
drivers behind you are seeing your
signals when, in fact, they are not. It’s
important to check occasionally to be
sure the trailer bulbs are still working.
You must also check the lights every
time you disconnect and then reconnect
the wires.
WARNING
Do not connect a trailer lighting system
directly to your vehicle’s lighting
system. Use an approved trailer wiring
harness.
Failure to do so could result in damage
to the vehicle electrical system and/or
personal injury.
We recommend that you have the
system checked by a HYUNDAI
authorised repairer as soon as possible.
Page 344 of 649
6-71
06
Driving on hills
Reduce speed and shift to a lower gear
before you start down a long or steep
downgrade. If you don’t shift down, you
might have to use your brakes so much
that they would get overheated and may
not operate efficiently.
On a long uphill grade, shift down and
reduce your speed to around 45 mph (70
km/h) to reduce the possibility of engine
and transmission overheating.
If your trailer weighs more than the
maximum trailer weight without trailer
brakes and you have an automatic
transmission/dual clutch transmission,
you should drive in D (Drive) when
towing a trailer. Operating your vehicle
in D (Drive) when towing a trailer will
minimise heat build-up and extend the
life of your transmission.
NOTICE
To prevent engine and/or transmission
overheating:
V When towing a trailer on steep
grades (in excess of 6%) pay close
attention to the engine coolant
temperature gauge to ensure the
engine does not overheat. If the
needle of the coolant temperature
gauge moves towards “H” (HOT),
pull over and stop as soon as it is
safe to do so, and allow the engine
to idle until it cools down. You may
proceed once the engine has cooled
sufficiently.
V You must decide your vehicle speed
according to the trailer weight and
uphill grade.
Parking on hills
Generally, if you have a trailer attached
to your vehicle, you should not park your
vehicle on a hill.
However, if you ever have to park your
trailer on a hill, here's how to do it:
1. Pull the vehicle into the parking space.
Turn the steering wheel in the
direction of the kerb (left if headed
down hill, right if headed up hill).
2. Shift the vehicle to P (Park, for
Automatic transmission/Dual clutch
transmission vehicle) or neutral (for
Manual transmission vehicle).
3. Set the parking brake and shut off the
vehicle.
4. Place wheel chocks under the trailer
wheels on the down hill side of the
wheels.
5. Start the vehicle, hold the brakes, shift
to neutral, release the parking brake
and slowly release the brakes until the
trailer chocks absorb the load.
6. Reapply the brakes and parking
brakes.
7. Move the shift lever to P (Park, for
Automatic transmission/Dual clutch
transmission vehicle) or the 1st gear
when the vehicle is parked on a uphill
grade and in R (Reverse) on a downhill
(for Manual transmission vehicle).
8. Shut off the vehicle and release the
vehicle brakes but leave the parking
brake set.
WARNING
To prevent serious or fatal injury:
Do not get out of the vehicle without
the parking brake firmly set. If you have
left the engine running, the vehicle can
move suddenly. You and others could
be seriously or fatally injured.
Page 351 of 649
07
7-5
CAUTION
[ The setting of the Warning Timing
and Warning Volume applies to
all functions of Forward Collision-
Avoidance Assist.
[ Even though, ‘Normal’ is selected for
Warning Timing if the front vehicle
suddenly stops the initial warning
activation time may seem late.
[ Select ‘Late’ for Warning Timing
when traffic is light and when driving
speed is slow.
Information
If the engine is restarted, Warning Timing
and Warning Volume will maintain the
last setting.
Forward Collision-Avoidance
Assist operation
Basic function
Warning and control
The basic function of Forward Collision-
Avoidance Assist is to help warn and
control the vehicle depending on
F R O O L V L R Q O H Y H O S & R O O L V L R Q : D U Q L Q JT
S ( P H U J H Q F \ % U D N L Q JT D Q G S 6 W R S S L Q J
Y H K L F O H D Q G H Q G L Q J E U D N H F R Q W U R OT
OBC3070002
Collision warning
[ To warn the driver of a collision, the
S & R O O L V L R Q : D U Q L Q JT Z D U Q L Q J P H V V D J H
will appear on the cluster and an
audible warning will sound and
the steering wheel will vibrate. (if
equipped)
[ If a vehicle is detected in front,
the function will operate when
your vehicle speed is between
approximately 6~112 mph (10~180
km/h).
[ If a pedestrian or cyclist is detected
in front, the function will operate
when your vehicle speed is between
approximately 6~50 mph (10~80
km/h).
[ , I S $ F W L Y H $ V V L V WT L V V H O H F W H G E U D N L Q J
may be assisted.
Page 352 of 649
Driver assistance system
7-6
OBC3070003
Emergency braking
[ To warn the driver that emergency
braking will occur, the ‘Emergency
% U D N L Q JT Z D U Q L Q J P H V V D J H Z L O O D S S H D U
on the cluster and an audible warning
will sound and the steering wheel will
vibrate. (if equipped).
[ If a vehicle is detected in front,
the function will operate when
your vehicle speed is between
approximately 6~37 mph (10~60
km/h).
[ If a pedestrian or cyclist is detected
in front, the function will operate
when your vehicle speed is between
approximately 6~37 mph (10~60
km/h).
[ In emergency braking situation,
braking is assisted with strong braking
power by the function to help prevent
collision with the vehicle, pedestrian
or cyclist ahead.
OBC3070004
Stopping vehicle and ending brake
control
[ When the vehicle is stopped due
to emergency braking, the ‘Drive
F D U H I X O O \T Z D U Q L Q J P H V V D J H Z L O O D S S H D U
on the cluster.
For your safety, the driver should
depress the brake pedal immediately
and check the surroundings.
[ Brake control will end after the vehicle
is stopped by emergency braking for
approximately 2 seconds.
WARNING
Take the following precautions when
using Forward Collision-Avoidance
Assist:
[ For your safety, change the Settings
after parking the vehicle at a safe
location.
[ With ‘Active Assist’ or ‘Warning Only’
selected, when ESC is turned off by
pressing and holding the ESC OFF
button for more than 3 seconds,
Forward Collision-Avoidance Assist
will turn off automatically. In this
case, the function cannot be set
from the Settings menu and the
warning light will illuminate on the
cluster which is normal. If ESC is
turned on by pressing the ESC OFF
button, Forward Collision-Avoidance
Assist will maintain the last setting.
Page 365 of 649
07
7-19
Forward Collision-Avoidance
Assist operation
Basic function
Warning and control
The basic function for Forward Collision-
Avoidance Assist is to help warn and
control the vehicle depending on the
F R O O L V L R Q O H Y H O S & R O O L V L R Q Z D U Q L Q JT
S ( P H U J H Q F \ E U D N L Q JT D Q G S 6 W R S S L Q J
Y H K L F O H D Q G H Q G L Q J E U D N H F R Q W U R OT
OBC3070002
Collision warning
[ To warn the driver of a collision, the
S & R O O L V L R Q : D U Q L Q JT Z D U Q L Q J P H V V D J H
will appear on the cluster, an audible
warning will sound and the steering
wheel will vibrate (if equipped).
[ If a vehicle is detected in front,
the function will operate when
your vehicle speed is between
approximately 6~112 mph (10~180
km/h).
[ If a pedestrian or cyclist is detected
in front, the function will operate
when your vehicle speed is between
approximately 6~53 mph (10~85
km/h).
[ , I S $ F W L Y H D V V L V WT L V V H O H F W H G E U D N L Q J
may be assisted.
OBC3070003
Emergency braking
[ To warn the driver that emergency
braking will be assisted, the
S ( P H U J H Q F \ % U D N L Q JT Z D U Q L Q J P H V V D J H
will appear on the cluster, an audible
warning will sound and the steering
wheel will vibrate (if equipped).
[ If a vehicle is detected in front,
the function will operate when
your vehicle speed is between
approximately 6~47 mph (10~75
km/h).
[ If a pedestrian or cyclist is detected
in front, the function will operate
when your vehicle speed is between
approximately 6~40 mph (10~65
km/h).
[ In emergency braking situation,
braking is assisted with strong braking
power by the function to help prevent
collision with the vehicle, pedestrian
or cyclist ahead.
Page 366 of 649
Driver assistance system
7-20
OBC3070004
Stopping vehicle and ending brake
control
[ When the vehicle is stopped due
to emergency braking, the ‘Drive
F D U H I X O O \T Z D U Q L Q J P H V V D J H Z L O O D S S H D U
on the cluster.
For your safety, the driver should
depress the brake pedal immediately
and check the surroundings.
[ Brake control will end after the vehicle
is stopped by emergency braking for
approximately 2 seconds.
Junction Turning function (if
equipped)
Function warning and control
Junction Turning function will help warn
and control the vehicle depending on
W K H F R O O L V L R Q O H Y H O S & R O O L V L R Q Z D U Q L Q JT
S ( P H U J H Q F \ E U D N L Q JT D Q G S 6 W R S S L Q J
Y H K L F O H D Q G H Q G L Q J E U D N H F R Q W U R OT
OBC3070007
Collision warning
[ To warn the driver of a collision, the
S & R O O L V L R Q : D U Q L Q JT Z D U Q L Q J P H V V D J H
will appear on the cluster, an audible
warning will sound and the steering
wheel will vibrate (if equipped).
[ The function will operate when
your vehicle speed is between
approximately 6~19 mph (10~30 km/h)
and the oncoming vehicle speed is
between approximately 19~44 mph
(30~70 km/h).
[ , I S $ F W L Y H D V V L V WT L V V H O H F W H G E U D N L Q J
may be assisted.
Page 367 of 649
07
7-21
OBC3070009
Emergency braking
[ To warn the driver that emergency
braking will be assisted, the
S ( P H U J H Q F \ % U D N L Q JT Z D U Q L Q J P H V V D J H
will appear on the cluster, an audible
warning will sound and the steering
wheel will vibrate (if equipped).
[ The function will operate when
your vehicle speed is between
approximately 6~19 mph (10~30 km/h)
and the oncoming vehicle speed is
between approximately 19~44 mph
(30~70 km/h).
[ In emergency braking situation,
braking is assisted with strong braking
power by the function to help prevent
collision with the oncoming vehicle.
Information
If the driver's seat is on the left side,
Junction Turning function will operate
only when the driver turns left. If the
driver's seat position is on right side, the
function will operate only when you turn
right.
OBC3070004
Stopping vehicle and ending brake
control
[ When the vehicle is stopped due
to emergency braking, the ‘Drive
F D U H I X O O \T Z D U Q L Q J P H V V D J H Z L O O D S S H D U
on the cluster.
For your safety, the driver should
depress the brake pedal immediately
and check the surroundings.
[ Brake control will end after the vehicle
is stopped by emergency braking for
approximately 2 seconds.
Page 379 of 649
07
7-33
Lane keeping assist
[ To warn the driver that the vehicle
is departing from the projected lane
in front, the green
indicator
light will blink on the cluster, and the
steering wheel will make adjustments
to keep the vehicle inside the lane.
[ The function will operate when
your vehicle speed is between
approximately 40~120 mph (60~200
km/h).
OBC3070015
Hands-off warning
If the driver takes their hands off the
steering wheel for several seconds,
W K H S . H H S K D Q G V R Q W K H V W H H U L Q J Z K H H OT
warning message will appear on the
cluster, and an audible warning will
sound in stages.
WARNING
[ The steering wheel may not be
assisted if the steering wheel is held
very tight or the steering wheel is
steered over a certain degree.
[ Lane Keeping Assist does not operate
at all times. It is the responsibility of
the driver to safely steer the vehicle
and to maintain the vehicle in its
lane.
[ The hands–off warning message
may appear late depending on road
conditions. Always have your hands
on the steering wheel whilst driving.
[ If the steering wheel is held very
lightly, the hands–off warning
message may appear because the
function may not recognise that the
driver has their hands on the steering
wheel.
[ If you attach objects to the steering
wheel, the hands-off warning may
not work properly.