wheel HYUNDAI I20 2023 Manual Online

Driver assistance system
7-72
OBC3070090TU
Warning overspeed
When driving at a speed higher than
the displayed speed limit, the red speed
limit indicator will blink.
OBC3070091ROBC3070092R
Changing set speed
If the speed limit of the road changes
during the operation of Manual Speed
Limit Assist or Smart Cruise Control,
an arrow in the direction of up or down
is displayed to inform the driver that
the set speed needs to be changed. At
this time, the driver can change the set
speed according to the speed limit by
using the + or – switch on the steering
wheel.
WARNING

[If the Speed limit tolerance is set over
‘0’, the set speed will change to a
higher speed than the speed limit of
the road. If you want to drive below
the speed limit, set the Speed limit
tolerance under '0' or use the
– switch on the steering wheel to
lower the set speed.

[Even after changing the set speed
according to the speed limit of the
road, the vehicle can still be driven
over the speed limit. If necessary,
depress the brake pedal to reduce
your driving speed.

[If the speed limit of the road is under
20 mph (30 km/h), the set speed
change function will not work.

[Intelligent Speed Limit Assist
operates using the speed unit in the
instrument cluster set by the driver.
If the speed unit is set to a unit other
than the speed unit used in your
country, Intelligent Speed Limit
Assist may not operate properly.
Information

07
7-103
Information
Highway Curve Zone Auto Slowdown and
Highway Set Speed Auto Change function
uses the same
symbol.
Highway Curve Zone Auto Slowdown

[Depending on the curve ahead on the
motorway, the vehicle will decelerate,
and after passing the curve, the
vehicle will accelerate to Smart Cruise
Control set speed.

[Vehicle deceleration time may differ
depending on the vehicle speed
and the degree of the curve on the
road. The higher the driving speed,
deceleration will start faster.
Highway Set Speed Auto Change

[Highway Set Speed Auto Change
function will operate when Smart
Cruise Control set speed and the
motorway speed limit is matched.

[Whilst Highway Set Speed Auto
Change function is operating, when
the motorway speed limit changes,
Smart Cruise Control set speed
automatically changes to the changed
speed limit.

[If adjusted Smart Cruise Control set
speed is different from the speed
limit, Highway Set Speed Auto Change
function will be in the standby state.

[If Highway Set Speed Auto Change
function has changed to the standby
state by driving on a road other than
the motorway main road, Highway
Set Speed Auto Change function will
operate again when you drive on the
main road again without setting the
set speed.
[If Highway Set Speed Auto Change
function has changed to the standby
state by depressing the brake pedal
or pressing the
switch on the
steering wheel, press the switch
to restart the function.

[Highway Set Speed Auto Change
function does not operate on highway
interchanges or junctions.
Information

Driver assistance system
7-110
OBC3070015
Hands-off warning
If the driver takes their hands off the
steering wheel for several seconds,
WKH
S.HHSKDQGVRQWKHVWHHULQJZKHHO
T
warning message will appear and an
audible warning will sound in stages.
First stage : Warning message
Second stage : Warning message (red
steering wheel) and
audible warning
OTM070117L
If the driver still does not have their
hands on the steering wheel after the
hands-off warning, the ‘LFA (Lane
)ROORZLQJ$VVLVWFDQFHOOHG
TZDUQLQJ
message will appear and Lane Following
Assist will be automatically canceled.
WARNING

[The steering wheel may not be
assisted if the steering wheel is held
very tight or the steering wheel is
steered over a certain degree.

[Lane Following Assist does not
operate at all times. It is the
responsibility of the driver to safely
steer the vehicle and to maintain the
vehicle in its lane.

[The hands–off warning message
may appear late depending on road
conditions. Always have your hands
on the steering wheel whilst driving.

[If the steering wheel is held very
lightly, the hands–off warning
message may appear because the
function may not recognise that the
driver has their hands on the steering
wheel.

[If you attach objects to the steering
wheel, the hands-off warning may
not work properly.
Information

07
7-111
„Lane undetected„Lane detected
OBC3070017OBC3070016

[If lane markings are not detected,
steering wheel control by Lane
Following Assist can be limited
depending on whether a vehicle is in
front or the driving conditions of the
vehicle.

[Even though the steering is assisted
by Lane Following Assist, the driver
may control the steering wheel.

[The steering wheel may feel heavier
or lighter when the steering wheel is
assisted by Lane Following Assist than
when it is not.
Lane Following Assist
malfunction and limitations
Lane Following Assist malfunction
OTM070118L
When Lane Following Assist is not
working properly, the ‘Check LFA
(Lane Following Assist) system warning
message will appear on the cluster for
several seconds, and the master (
)
warning light will illuminate on the
cluster. If the master warning light
illuminates, we recommend that the
vehicle be inspected by a HYUNDAI
authorised repairer.
Limitations of Lane Following Assist
For more details on function limitations,
refer to “Lane Keeping Assist (LKA)”
section in chapter 7.
WARNING
For more details on the function
precautions, refer to “Lane Keeping
Assist (LKA)” section in chapter 7.

07
7-127
Rear Cross-Traffic Collision-
Avoidance Assist operation
Warning and control
Rear Cross-Traffic Safety system will
warn and control the vehicle depending
RQFROOLVLRQOHYHO
S&ROOLVLRQ:DUQLQJ
T

S(PHUJHQF\%UDNLQJ
TDQG
S6WRSSLQJ
YHKLFOHDQGHQGLQJEUDNHFRQWURO
T
ORG3070025OBC3070046TU
OBC3050125TU
Collision warning

[To warn the driver of an approaching
vehicle from the rear left/right side
of your vehicle, the warning light on
the outside rearview mirror will blink
and a warning will appear on the
cluster. At the same time, an audible
warning will sound and the steering
wheel will vibrate (if equipped). If Rear
View Monitor is operating, a warning
will also appear on the infotainment
system screen.
[The function will operate when all the
following conditions are satisfied:
- The gear is shifted to R (Reverse)
- Vehicle speed is below 5 mph (8
km/h)
- The approaching vehicle is within
approximately 25 m (82 ft.) from the
left and right side of your vehicle
- The speed of the vehicle
approaching from the left and right is
above 3 mph (5 km/h)
Information
If the operating conditions are satisfied,
there will be a warning whenever the
vehicle approaches from the left or right
side even though your vehicle speed is 0
mph (0 km/h).

Driver assistance system
7-128
ORG3070025OBC3070077
OBC3050125TU
Emergency braking

[To warn the driver of an approaching
vehicle from the rear left/right side
of your vehicle, the warning light
on the outside rearview mirror will
blink and, the 'Emergency braking'
warning message will appear on the
cluster. At the same time, an audible
warning will sound and the steering
wheel will vibrate (if equipped). If Rear
View Monitor is operating, a warning
will also appear on the infotainment
system screen.
[The function will operate when all the
following conditions are satisfied:
- The gear is shifted to R (Reverse)
- Vehicle speed is below 5 mph (8
km/h)
- The approaching vehicle is within
approximately 1.5 m (5 ft.) from the
left and right side of your vehicle
- The speed of the vehicle
approaching from the left and right is
above 3 mph (5 km/h)

[Emergency braking will be assisted
to help prevent collision with
approaching vehicles from the left and
right.
WARNING
Brake control will end when:
- The approaching vehicle is out of the
detecting range
- The approaching vehicle passes
behind your vehicle
- The approaching vehicle does not
drive toward your vehicle
- The approaching vehicle speed slows
down
- The driver depresses the brake pedal
with sufficient power

07
7-145
Reverse Parking Collision-
Avoidance Assist operation
Operating conditions
,I
S$FWLYHDVVLVW
TRU
S:DUQLQJRQO\
TLVVHW
from the Settings menu, Reverse Parking
Collision-Avoidance Assist will be in
the ready status when the following
conditions are satisfied:
- The tailgate is closed
- The gear is shifted to R (Reverse)
- The vehicle is below 6 mph (10 km/h)
- Function components such as the rear
view camera and the rear ultrasonic
sensors are in normal conditions
When Reverse Parking Collision-
Avoidance Assist activates, a line
appears behind the vehicle image in the
instrument cluster.
Reverse Parking Collision-Avoidance
Assist operates only once after the gear
is shifted to R (Reverse). To reactivate
Reverse Parking Collision-Avoidance
Assist, shift the gear from another gear
to R (Reverse).
OBC3070113TU
Active assist

[If the function detects a risk of
collision with a pedestrian or an
object, the function will warn the
driver with an audible warning,
steering wheel vibration (if equipped)
and warning message on the cluster.
When Rear View Monitor is operating,
a warning will appear on the
infotainment system screen.

[If the function detects an imminent
collision with a pedestrian or an object
behind the vehicle, the function will
assist you with braking. The driver
needs to pay attention as the brake
assist will end within 2 seconds. The
driver must immediately depress
the brake pedal and check vehicle
surroundings.

[Brake control will end when:
- The gear is shifted to P (Park) or D
(Drive).
- The driver depresses the brake pedal
with sufficient power
- Braking assist has last for
approximately 2 seconds

[The warning will turn off when:
- The driver shifts the gear to P (Park),
N (Neutral) or D (Drive)

[The brake control may not operate
properly depending on the status of
ESC (Electronic Stability Control).
There will only be a warning when:
- The ESC (Electronic Stability Control)
warning light is on
- ESC (Electronic Stability Control) is
engaged in a different function

Driver assistance system
7-146
Warning Only

[If the function detects a risk of
collision with a pedestrian or an
object, the function will warn the
driver with an audible warning,
steering wheel vibration (if equipped)
and warning message on the cluster.
When Rear View Monitor is operating,
a warning will appear on the
infotainment system screen.

[ ,I
S:DUQLQJRQO\
TLVVHOHFWHGEUDNLQJ
will not be assisted.

[The warning will turn off when the
gear is shifted to P (Park), N (Neutral)
or D (Drive).
Reverse Parking Collision-
Avoidance Assist malfunction
and limitations
Reverse Parking Collision-
Avoidance Assist malfunction
OBC3070058
When Reverse Parking Collision-
Avoidance Assist or other related
systems are not working properly, the

S&KHFN3DUNLQJ6DIHW\V\VWHP
TZDUQLQJ
message will appear on the cluster, and
the function will turn off automatically.
We recommend that the function be
inspected by a HYUNDAI authorised
repairer.
Reverse Parking Collision-
Avoidance Assist disabled
OBC3070042
The rear view camera is used as a
detecting sensor to detect pedestrians. If
the camera lens is covered with foreign
material such as snow or rain, it may
adversely affect camera performance
and Reverse Parking Collision-Avoidance
Assist may not operate normally. Always
keep the camera lens clean.
OBC3070060
The rear ultrasonic sensors are located
inside the rear bumper to detect objects
in the rear area. If the sensors are
covered with foreign material, such as
snow or rain, it may adversely affect
sensor performance and Reverse Parking
Collision-Avoidance Assist may not
operate normally. Always keep the rear
bumper clean.

Driver assistance system
7-154
Operating order
Parking mode operates in the following
order:
1. Getting ready for parking
2. Selecting parking mode and type
3. Searching for parking space
4. Recognizing parking space
5. Search complete
6. Steering wheel control
7. Parking complete

[Parking Assist will help you
with parallel reverse parking or
perpendicular reverse.
OBC3070044R
1. Getting ready for parking
(1) With the engine turned on, depress
the brake pedal and shift the gear to
D (Drive).
- If the vehicle is driven above 3 mph
(5 km/h) after the engine is turned
on, Parking mode can be selected
when the gear is in N (Neutral)
(2) Press and hold the Parking/View
(
) button to turn on Parking Assist.
A message will appear on the cluster
and the Parking Safety (
) button
indicator light will illuminate.
[If the engine is turned on when the
gear is in N (Neutral), Exit mode
will be selected. Parking mode will
be selected automatically after the
vehicle has been driven.

[Parking Assist is turned off whenever
the engine is restarted. Press the
Parking/View (
) button to turn use
Parking Assist again.
2. Selecting parking mode and type
(1) Select parking mode by pressing the
Parking/View (
) button briefly.
Parking type will change whenever
the button is pressed. Right parallel
UHYHUVHSDUNLQJ

07
7-157
OBC3070099TU
6. Steering wheel control
(1) Shift the gear to R (Reverse).
(2) Parking Assist will provide
instructions on the cluster and the
steering wheel will be controlled.
- If the steering wheel is held tight,
Parking Assist will be cancelled.
(3) Take your foot off the brake pedal
and drive in reverse.

[Do not drive above 4 mph (7 km/h).
Parking Assist will be cancelled if
the vehicle speed is above 4 mph (7
km/h). OBC3070100TU/OBC3070101TU
OBC3070102TU
6-1. Gear shift request during steering
wheel control
(1) Depending on the parking
environments, shift request messages
(Shift to the 1st gear, Shift to R, Shift
to D) will appear on the cluster along
with a beep sound.
(2) Shift the gear according to the
message and park the vehicle using
the brake pedal.

[If you do not follow the instructions
on the cluster, parking may be
incomplete or the vehicle may not be
parked straight.