Button od Hyundai Matrix 2006 Workshop Manual

1CONTROLS AND EQUIPMENT
64
CAUTION:
o Do not open the sunroof in se- verely cold temperature or when it is covered with ice or snow.
o Periodically remove any dirt that
may have accumulated on theguide rails.
o Do not press any sunroof control button longer than necessary.Damage to the motor or system components could occur. SB330C1-E Tilting the Sunroof System
HFC2022
The sunroof can be tilted and closed by depressing the button indicated. Re-lease the button when the sunroof reaches the up position. NOTE: The sunroof should not be opened when water or standing rain is on the roof panel. Driving the vehicle for a short distance will allow the water todisperse naturally at which point the sunroof may be opened. B460D01FC-EAT Manual Operation of Sunroof If the sunroof fails to operate:
HFC1036
1. Remove the rectangular plastic inte- rior light lenses in the front overhead console.
HFC1037
!
!WARNING:
o Do not close a sunroof if anyone's hands, arms or body are between the sliding glass and the sunroof sash, as this could result in injury.
o Do not place your head or arms
out of the sunroof opening at anytime.

1
CONTROLS AND EQUIPMENT
65
SB340B2-E Interior Light The interior courtesy light has a button of three positions. The three positions are:
oDR In the "DR" position, the interior cour- tesy light comes on when any door is opened regardless of the ignition key position. The light goes out when thedoor is closed.
oON In the "ON" position, the light stays on at all times.
2. Turn the hexagonal bolts with a socket
wrench counterclockwise to removethe front overhead console.
3. Insert the hexagonal head wrench
provided with the vehicle into thesocket. This wrench can be found in the vehicle's luggage room or glove box.
HFC1038
4. Turn the wrench clockwise to open or counterclockwise to close. B480A01E-EAT Map Light
INTERIOR LIGHT
The two map lights are located at each side of the interior light. The lights may be operated by depress- ing the switch to turn on the light andpressing again to turn off the light. This light produces a spot beam for conve- nient use as a map light at night or asa personal light for the driver or the passenger.
HFC490
With Sunroof Without SunroofWith Sunroof HFC480
Without Sunroof

1CONTROLS AND EQUIPMENT
80HEATING CONTROLS
B690A02S-AAT
With the "Fresh" mode selected, air enters the vehicle from the outside andis heated or cooled according to the function selected. With the "Recirculation" mode selected, air from within the passenger compart- ment will be drawn through the heatingsystem and heated or cooled according to the function selected. NOTE:
o It should be noted that prolonged
operation of the heating in "Recir- culation" mode will increase fog- ging of the windscreen and sidewindows and the air within the passenger compartment will be- come stale. In addition, prolongeduse of the air conditioning with the "Recirculation" mode selected may result in the air within thepassenger compartment becom- ing excessively dry.
o When the ignition switch is turned
"ON" the air intake control willchange to (
) mode (regardless
of switch position). This is normal operation.
B690A02FC
For normal heating operation, set the air intake control to the "Fresh" position and the air flow control to "Floor". For faster heating, the air intake control should be in the "Recirculation" posi- tion. If the windows fog up, move the air flow control to the "Def" (defroster) position.(The A/C will turn on automatically and "Fresh" mode will be activated.) For maximum heat, rotate the tempera- ture control to "Warm".
B670C02FC-EAT Air Intake Control This is used to select fresh outside air or recirculation inside air. To change the air intake control mode, (Fresh mode, Recirculation mode) pushthe control button. FRESH MODE (
)
: The indicator
light on the button goes off when the air intake control is in fresh mode. RECIRCULATION MODE (
) : The
indicator light on the button is illuminat- ed when the air intake control is inrecirculation mode.
HFC2067

1CONTROLS AND EQUIPMENT
82
B730A01L-EAT Operation Tips
o To keep dust or unpleasant fumesfrom entering the car through the ventilation system, temporarily set the air intake control at "Recircula- tion". Be sure to return the control to"Fresh" when the irritation has passed to keep fresh air in the ve- hicle. This will help keep the driveralert and comfortable.
o Air for the heating/cooling system is
drawn in through the grilles just aheadof the windscreen. Care should be taken that these are not blocked by leaves, snow, ice or other obstruc-tions.
o To prevent interior fog on the
windscreen, set the air intake controlto the fresh air ( ) position, and fan speed to the desired position, turn on the air conditioning system,and adjust temperature control to desired temperature.AIR CONDITIONING SYSTEM
B740A01S-EAT Air Conditioning Switch (Not all models)
HFC2069
To remove the frost or exterior fog on the windscreen;
o Set the air flow control to the defrost (
) position. (The A/C will turn on
automatically and "Fresh" mode will be activated.)
o Set the temperature control to warm.
o Set the fan speed control to position
"3" or "4".
NOTE: When the A/C is operated continu- ously on the floor-defrost level (
) or
defrost level (
), it may cause fog to
form on the exterior windscreen. If this occurs, set the air flow control tothe face level position (
)and fan
speed control to the low position. HFC2108
The air conditioning is turned on or off by pushing the A/C button on the heat- ing/air conditioning control panel.

1
CONTROLS AND EQUIPMENT
87
B980B01NF-AAT Fan Speed Control Switch The fan speed can be set to the desired speed by turning the appropriate fan speed control knob. The higher the fan speed is, the more air is delivered.Pressing the "OFF" button turns off the fan. B670C02Y-EAT Air Intake Control Switch (Without A.Q.S) This is used to select fresh outside air or recirculation inside air. To change the air intake control mode,(Fresh mode, Recirculation mode) push the control button. FRESH MODE
( ) : The indicator
light on the button comes on when the air intake control is fresh mode. RECIRCULATION MODE ( ) : T h e
indicator light on the button is illumi- nated when the air intake control is recirculation mode. HFC240
HFC225
B980A01Y-AAT MANUAL OPERATION The heating and cooling system can be controlled manually as well as by push- ing buttons other than the "AUTO" but-ton. In this state, the system sequen- tially works according to the order of buttons selected.The function of the buttons which are not selected will be controlled automati- cally.Press the "AUTO" button in order to convert to automatic control of the sys- tem.

1
CONTROLS AND EQUIPMENT
89
!
CAUTION:
If the windows fog up with the Recir- culation or A.Q.S mode selected, set the air intake control to the Fresh airposition or A.Q.S control to "OFF". B980D01Y-AAT Heating and Cooling System Off
Recirculation mode :
Air from within the passenger compart- ment will be drawn through the heating system and heated or cooled accordingto the function selected.
Exhaust gas cutoff mode :
Air enters the vehicle from the outside.But if exhaust gas enters the vehiclefrom the outside, the exhaust gas cut- off mode ( ) is automatically conv- erted to the ( ) mode, to preventexhaust gas from entering the vehicle. NOTE: It should be noted that prolonged operation of the heating system inrecirculation mode ( ) will give rise to misting of the windscreen and side windows and the air within thepassenger compartment will become stale. In addition, prolonged use of the air conditioning with the recircu-lation mode ( ) selected may result in the air within the passenger compartment becoming excessivelydry.
Press the "OFF" button to stop the operation of the heating and cooling system. HFC239

1
CONTROLS AND EQUIPMENT
91
B980F02E-EAT Defrost Switch When the "Defrost" button is pressed, the " " mode will be automatically selected and the air will be dischargedthrough the windshield defroster nozzle, side defroster nozzle and side ventila- tor. To assist in defrosting, the airconditioning will operate if ambient tem- perature is higher than 38.3°F (3.5°C) and automatically turns off if the ambi-ent temperature drops below 38.3°F (3.5°C). HFC241
Floor-Defrost Level
When selecting the "Floor-Defrost Level"mode, the indicator light will come on and the air will be discharged throughthe windscreen defroster nozzle, the floor vents, side defroster nozzle and side ventilator.
HFC234-DHFC233-D
Floor-Level
When selecting the "Floor-Level", the indicator light will come on and the air will be discharged through the floorvents, windscreen defroster nozzle, side defroster nozzle and side ventila- tor.

2 DRIVING YOUR HYUNDAI
10
!
C090A01A-GAT
NOTE:
Depress the brake pedal and push the button when shifting. Push the button when shifting.The selector lever can be shifted freely.
For optimum fuel economy, accelerate gradually. The transaxle will automati-cally shift to the second, third and overdrive gears.
The highly efficient Hyundai automatic transaxle has four forward speeds and one reverse speed. It has a conven-tional shift pattern as shown in the illustration. At night, with the first posi- tion of the multi-function switch, theappropriate symbol on the shift pattern indicator will be illuminated according to the range selected.
CAUTION:
Never shift into "R" or "P" position whilst the vehicle is moving. AUTOMATIC TRANSAXLE
YC090A1-E Selector Positions o P (Park): With the selector in this position, no drive is transmitted from the engine and the transaxle output and therefore the front wheels locked. The engine may bestarted with the selector in this position.
!CAUTION:
The selector must NEVER be shifted to the "P" position whilst the vehicle is in motion, otherwise serioustransaxle damage will result. DC110C1-E o R (Reverse): With the selector in this position, re- verse gear will be engaged. The enginemay not be started with the selector in this position.
!
CAUTION:
The selector must NEVER be shifted to the "R" position whilst the vehicle is in motion.
DC110D1-E o N (Neutral): With the selector in this position, no gear is selected and no drive is trans- mitted from the engine. The engine maybe started with the selector in this position.
! CAUTION:
Do not coast with the selector at the "N" position.
C090A01FC-D

2 DRIVING YOUR HYUNDAI
12
SC130A1-E Overdrive Switch The overdrive switch prevents the transaxle upshifting higher than third gear when the switch is turned "OFF".The transaxle will start from rest in first gear and upshift to second and third gear depending upon the roadspeedand throttle opening but will not upshift to fourth gear. When the overdrive switch is turned "ON", the transaxle will startfrom rest in first gear and will upshift, depending upon roadspeed and throttle opening to second, third and fourthgear. Therefore, when the overdrive switch is turned "OFF", the transaxle performs as a three speed unit and theoverdrive warning light located in the instrument cluster will be illuminated. HFC3023-D
When the overdrive switch is turned "ON", the transaxle functions as a fullyautomatic four speed unit with the maxi- mum fuel economy potential of the vehicle being realized. FC120D3-E General Operating Instructions
o The button in the selector handle
must be depressed before the selec- tor can be moved.
o The engine may only be started when the selector is at position "P" or "N".
o Ensure that the footbrake is firmly
applied when shifting from "P" or "N" to "D", "2", "L" or "R" and vice versa.
o Always engage the parking brake
when the vehicle is unattended, neveruse the "P" position in place of the parking brake.
o Under normal circumstances, the se- lector should be placed in the "D"position and the transaxle allowed to select the most ideal ratio for thecircumstances. In this position maxi- mum fuel economy will be achieved. o When descending steep gradients
where engine braking is required, the selector should be placed at the "2" or "L" position depending upon the vehicle speed.
o When ascending steep gradients using large throttle openings, thetransaxle may repeatedly changebetween two adjacent ratios. This is a normal characteristic and may be prevented by cancelling the over-drive facility if the shifting occurs between third and fourth ratios, se- lecting position "2" if the shiftingoccurs between third and second ratios or selecting position "1" if the shifting occurs between first andsecond ratios.
o Never move the selector to or from
the "P" or "N" position with the accel-erator depressed.
o Ensure that the overdrive switch is at
the "ON" position for maximumeconomy.
o If rapid acceleration is required, fully
depress the accelerator pedal. Inthis condition, the kickdown mecha- nism will be operated and the transaxle will automatically down-shift according to the vehicle speed.

6 OWNER MAINTENANCE
32
G350B01FC-EAT
(Diesel engine)
The fuel system should be bled to remove air as described in the illustra-tion if the fuel supply is exhausted during travel, when the fuel filter is replaced, or if the vehicle is not usedfor a long time.
1. Remove the air cap with pushing the button.
G350A01FC
BLEEDING THE FUEL SYSTEM
POWER STEERING FLUID LEVEL
SG230A1-E
HFC5004
G230A02FC
Petrol engine
Diesel engine
The power steering fluid level should
be checked daily. SG230B1-E
POWER STEERING HOSES
Power steering hoses should be
checked for damage, deterioration and leakage at each service. To check the power steering fluid level,
be sure the ignition is "OFF", thencheck to make certain that the power steering fluid level is between the "MAX" and "MIN" level markings onthe fluid reservoir.
NOTE: Grinding noise from power steering
pump may be heard immediately after the engine is started in ex-tremely cold condition (below -4°F). If the noise stops dur- ing warm up, there is no abnormalfunction in the system. This is due to a power steering fluid character- istic in extremely cold conditions. FLUID RECOMMENDATION
Only automatic transmission fluid
meeting the specification of PSF-3 or Dexron 2 should be used in the power steering system.