engine Hyundai Matrix 2007 Owner's Manual

6
OWNER MAINTENANCE
7
!
SG030C2-E
Engine Oil Level
HFC5007
Petrol engine
G030C02FC
Diesel engine SG030D3-E
Engine Oil Replenishment
HFC5009
Petrol engine
Diesel engine
The engine oil level should be checked with the engine at normal operating temperature and the vehicle parkedupon level ground. If the indicated oil level is at or below the lower mark of the dipstick, oil should be added until the level is at orbelow the upper mark.
WARNING:
Be very careful not to touch the
radiator hose when checking the engine oil as it may be hot enough to burn you. Prior to checking the level, the vehicle
should be allowed to stand for severalminutes after the engine has been switched off to allow the oil to drain back to the sump.
Withdraw the dipstick and wipe it with
a clean rag. Replace the dipstick fullyand withdraw again when the oil levelmay be read from the stick. Normal oil level is indicated when the oil is present between the two marks on the stick. Itis not necessary to add oil if the level is above the lower mark and in any case, oil must not be added to thedegree that the level exceeds the up- per mark. Replace the dipstick fully after checking the level.
G030D03FC
fcuk-6.p65 12/27/2006, 10:16 AM
7

6 OWNER MAINTENANCE
8
ZG030E1-A
ENGINE OIL CONSUMPTION Function of engine oil
Engine oil has the primary function of lubricating and cooling the inside of the engine.
Engine oil consumption It is normal that an engine should consume some engine oil in the course of normal driving. The cause of oil consumption in a normal engine are asfollows;
o Engine oil is used to lubricate pis- tons, piston rings and cylinders. A thin film of oil is left on the cylinder wall when a piston moves downwards in the cylinder. High negative pressure generated duringengine operation sucks some of the oil into the combustion chamber. This oil with some oil of the cylinder wall is burned by the high tempera- ture combustion gases during thecombustion process.
To add oil to the engine, remove the
filler cap by rotating in an counter-clockwise direction and pour engine oil into the engine. Before checking the level again, allow several minutes forthe oil to drain into the sump. Replace the oil filler cap rotating it in a clock- wise direction until tight.
The quantity of oil required to raise the
level from the minimum to maximumlevel is approximately 1 litre.
The distance between the "F" and "L"
marks is equal to about 1 liter(Petrol Engine)/1.2 liter(Diesel Engine) of oil.
!
CAUTION:
Slowly pour the recommended oil into a funnel. Do not overfill toprevent engine to damage.!
WARNING:
Be very careful not to touch the radiator hose when checking the engine oil as it may be hot enoughto burn you. o The engine oil consumption is
strongly effected by the viscosityand quality of oil, engine rpm and driving condition etc. More engine oil may be consumed under severe driving conditions such as high speeds, frequent accelera- tion and deceleration, compared tonormal driving.
fcuk-6.p65 12/27/2006, 10:16 AM
8

6
OWNER MAINTENANCE
9ENGINE OIL AND FILTER REPLACEMENT
SSA6040A
1.6 DOHC
Oil filler cap
Drain plug
Oil filler
G040A03E
Oil filler cap
Drain plug
Oil filler
1.8 DOHC
SG040A2-E
Petrol engine The engine oil and filter must be changed at the time or mileage inter-val specified in the maintenance sched- ule. If the vehicle is operated under severe or adverse conditions, the oiland filter must be replaced more fre- quently. To replace the oil and filter, proceed as follows:
1. Ensure that the engine is at normal operating temperature and park the vehicle on level ground with the parking brake securely applied andthe engine turned off.
2. Open the bonnet and remove the oil filler cap.
3. Prepare a suitable receptacle to collect the displaced oil and re-move the drain plug from the sump.
CAUTION:
The oil being drained from the en-gine will be hot. Care should beexercised to prevent scalding. 4. When the oil has drained from the
sump, replace the drain plug usinga new gasket ensuring that the plug is not over tightened.
5. Remove the oil filter by rotating counterclockwise, using a propri-etary oil filter removal tool if neces- sary. Note that the oil filter willcontain approximately 0.5 litres of oil and this should be collected in a suitable receptacle.
6. Install a new oil filter having smeared
the sealing ring with clean oil androtating clockwise until the filter contacts the mounting and then a further one half turn. Do not over-tighten Tightening torque: 2.3 ~ 2.5 kgf.m
7. Remove the engine oil level dip- stick.
8. Pour the specified quantity of the
recommended oil into the engine and replace the filler cap. Start the engine and ensure that no oil leaksexist. Turn off the engine and after a couple minutes, recheck the oil level.
!
fcuk-6.p65 12/27/2006, 10:16 AM
9

6 OWNER MAINTENANCE
10
G040B04FC-EAT
Diesel engine
Oil filter
G040B01FC
Oil filler cap
Centrepipe O-ring G040B02FC
Upper capO-ring
Oil filter element
Oil filterhousing
The engine oil and filter should be
changed at those intervals specified in the maintenance schedule in Section 5. If the car is being driven in severe conditions, more frequent oil and filter changes are required.
The procedure for changing the oil and
filter is as follows:
1. Park the car on level ground and set the parking brake. Start the engine and let it warm up until the needle on the coolant temperature gauge moves above the lowest mark. Turn the engine off and place the gear selector lever in "P" (automatic) or reverse gear (manual transaxle). 2. Open the bonnet and remove the
engine oil level dipstick.
3. Loosen the oil filter upper cap with a proper tool from the oil filter housing until an O-ring is seen. Then, drainthe oil completely.
CAUTION:
Slowly loosen the oil filter uppercap not to overflow the oil.
!
!
CAUTION:
Slowly pour the recommended oil into a funnel. Do not overfill to prevent engine to damage.!
WARNING:
Prolonged and repeated contact with used engine oils may result in seri- ous skin disorders including der- matitis and cancer. Avoid contact with skin as far as possible andalways wash thoroughly after any contact. Keep used oils out of reach of children. It is illegal to pollutedrains, water courses and soil. Use only authorized waste collection facilities including civic amenitysites and garages for the disposal of used oil and oil filters. If in doubt, contact the local authority for dis-posal instructions.
fcuk-6.p65 12/27/2006, 10:16 AM
10

6
OWNER MAINTENANCE
11
!
!
4. Remove the engine oil filler cap.
5. Slide underneath the car and loosen
the oil pan drain plug by turning it counterclockwise oil pan with a wrench of the proper size. Be surethat a drain pan is in position to catch the oil as it drains out, then remove the drain plug.
WARNING:
Be very careful when draining theengine oil as it may be hot enough to burn you!
6. When the oil has stopped draining, replace the drain plug using a new gasket and retighten by turning it clockwise. Oil pan drain plug tightening torque : 3.5 ~ 4.5 kgf.m
7. Pull out the oil filter upper cap with element from the oil filter housing.Using a clean cloth, remove any dirtor oil accumulated around the oilfilter housing. 8. After mounting a new centrepipe O-
ring, new oil filter element and newO-ring to upper cap, install the up- per cap to oil filter housing and retighten by turning it clockwise. Donot over-tighten. Tightening torque : 2.5 kgf.m
CAUTION:
Do not use old oil filter upper cap O- ring and centrepipe O-ring.
!
9. Refill the crankcase with the recom- mended engine oil. Refer to the specification in chapter 9 for engine oil capacity.
CAUTION:
Slowly pour the recommended oilinto a funnel. Do not overfill to preverd engine to camage.
! 10. Start the engine and check to be
sure no oil is leaking from the drain plug or oil filter.
11. Shut off the engine and recheck
the oil level.
NOTE:
o It is recommended that the en- gine oil and filter should be changed by an Hyundai authorised repairer.
o Always dispose of used engine oil in an environmentally accept-able manner. It is suggested that it be placed in a sealed container and taken to a service station formaybe reclaimation. Do not pour the oil on the ground or put it into the household trash.
WARNING:
Used motor oil may cause irritation or cancer of the skin if left in contact with the skin for prolonged periodsof time. Wash your hands thoroughly with soap and warm water as soon as possible after handling used oil.
fcuk-6.p65 12/27/2006, 10:16 AM
11

6 OWNER MAINTENANCE
12
!
ENGINE COOLANT CHECK- ING AND REPLACING
SG050B1-E Coolant recommended G050B01FC
SG050A1-E
WARNING:
Do not remove the radiator cap when the engine is hot, since the system is pressurised and coolant may be ejected from the radiator resultingin scalding.
G050B02FC
Petrol engine Diesel engine
Only ethylene glycol based coolantwith a corrosion inhibitor suited to alu- minium alloy engine components should be used in the cooling system. No further additives or inhibitors should be used. The coolant specific gravityshould be checked as prescribed in the maintenance schedule to ensure adequate frost and corrosion protec-tion. In addition, the engine coolant must be replaced at the specified in- terval since the corrosion inhibitor prop-erties deteriorate with time. It is important to note that whilst an
increase in the concentration of antifreeze gives an increase in the level of frost protection, a solution which is in excess of 65% anti freeze will result inreduced frost protection and engine overheating. Therefore the recom- mended concentration of 50% shouldnot be exceeded for general use. The use of methanol based anti freeze
compounds may result in engine over-heating and will invalidate the vehicle warranty.
NOTE: It is imperative that vehicles fitted
with an air conditioning system have a coolant concentration of the rec-ommended strength at all times. The use of the air conditioning sys- tem when the cooling system isfilled with water only will result in the heater matrix freezing and sub- sequently bursting.
fcuk-6.p65 12/27/2006, 10:16 AM
12

6
OWNER MAINTENANCE
13
SG050C1-E
To Check the Coolant Level If the level is below the "L" mark, add coolant of the correct concentrationuntil the level is between the "L" and "F" marks. If the level falls below the "L" mark on a regular basis despitebeing topped up, consult a Hyundai authorised repairer.
G050C01FC G050C02FC
Petrol engine
Diesel engine
The engine coolant level may be observed through the side of the plas- tic coolant reservoir (expansion tank) when the engine is cold.
G050D01FC
SG050D2-E
To Change the Coolant
The coolant should be changed at
those intervals specified in the vehicle maintenance schedule in Section 5.
NOTE: Care should be taken to ensure that
coolant is not allowed to spill onto the paintwork since the finish maybecome damaged. If coolant spill- age occurs, the affected area should be rinsed thoroughly with water.
1. Park the vehicle on level ground
and ensure that the parking brake is firmly applied, and the engine al- lowed to cool. Do not attempt this operation whilst the engine is hot since burning or scalding may result. 2. Prepare a suitable receptacle to
collect the displaced coolant and position this under the radiator drain tap.
3. With the heater temperature control set to the "HOT" position, removethe radiator cap and open the radia- tor drain tap.
4. When the engine coolant has drained completely, close the drain tap en-suring that this is not over tight- ened.
5. Prepare a suitable quantity of new engine coolant (refer to section 9)and pour this into the radiator.
fcuk-6.p65 12/27/2006, 10:16 AM
13

6 OWNER MAINTENANCE
14AIR CLEANER ELEMENT REPLACEMENT
G070A01E-EAT
HFC5003
Petrol engine
G070A02FC
Diesel engine
To replace the air cleaner element, remove the air intake ducting from theair flow sensor body and unfasten the spring clips holding the air flow sensor top to the body.
!
G050D02FC
6. Start the engine with the radiator cap still removed and continue to add coolant as the level decreases as air is expelled from the system.When the level remains constant, replace the radiator cap and replen- ish the coolant reservoir.
7. When the engine is hot, check to ensure that no coolant leaks arepresent. WARNING:
The cooling fan is controlled by
engine coolant temperature and maysometimes operate even when theengine is not running. Use extreme caution when working near the blades of the cooling fan so thatyou are not injured by a rotating fan blade. As the engine coolant tem- perature decreases, the fan will au-tomatically shut off. This is a nor- mal condition.
fcuk-6.p65 12/27/2006, 10:16 AM
14

6
OWNER MAINTENANCE
15
!
Lift out the air flow sensor followed by the air cleaner element. Replacementof the element is the reverse of the above.
CAUTION:
o The air flow sensor is a precision engineered electronic measuringdevice and therefore care should be exercised that the air flow sen-sor is not damaged during re- placement of the element.
o When removing the air cleaner element, be careful that dust or dirt does not enter the air intake.These may result in damage to the air cleaner element.
To ensure maximum filtration perfor-mance and continued engine perfor- mance, only genuine Hyundai replace-ments should be used.
WINDSCREEN WIPER BLADES
G080A01A-EAT The wiper blades should be carefully inspected from time to time and cleaned to remove accumulations ofroad film or other debris.To clean the wiper blades and arms,use a clean sponge or cloth with a mild soap or detergent and water. If the wipers continue to streak or smear theglass, replace them with genuine Hyundai replacement. HEF119
!
CAUTION:
o Do not operate the wipers on dry glass since rapid wear and dam- age to the windscreen glass mayresult.
o Keep the blade rubber out of con- tact with petroleum products suchas engine oil, petrol, etc.
fcuk-6.p65 12/27/2006, 10:16 AM
15

6
OWNER MAINTENANCE
17
The level of windscreen washer fluid available should be checked on a daily basis. The level of fluid will be visible through the side of the reservoir.When the fluid is to be replenished, only a proprietary screen wash addi- tive should be used and in the concen- tration recommended by the manufac- turer. The windscreen washer reser- voir has a total capacity of 3 litres.
WINDSCREEN WASHER RESERVOIR REPLENISH- MENT
SG090A2-E
HFC5010
!CAUTION:
Engine coolant anti freeze must not be used in the windscreen washer system since damage to thepaintwork may result.
Undiluted windscreen washer addi-tive must not be allowed to comeinto contact with the paintwork. If spillage occurs, flush the affected area immediately with water. Do notoperate the windscreen washer for more than 15 seconds continuously or when the reservoir is empty since damage to the washer pump will result.
HHR5051
2. Pull up the wiper blade until you hear an audible "click" to engage in the end of the wiper arm.
NOTE: Do not allow the wiper arm to fall
against the windscreen.
fcuk-6.p65 12/27/2006, 10:16 AM
17