stop start HYUNDAI PALISADE 2023 Owner's Guide
[x] Cancel search | Manufacturer: HYUNDAI, Model Year: 2023, Model line: PALISADE, Model: HYUNDAI PALISADE 2023Pages: 661, PDF Size: 16.01 MB
Page 200 of 661
05
5-51
3. While the HomeLink indicator light S is flashing orange, press and hold the
hand-held remote button. Continue
pressing the handheld remote button
until the HomeLink indicator light S
light changes from orange to green.
You may now release the handheld
remote button.
4. Wait until your garage door comes to a complete stop, regardless of
position, before proceeding to the
next steps.
5. Press and release the HomeLink button you are programming and
observe the indicator light.
[ If the indicator light remains solid
green, your device should operate
when the HomeLink button is
pressed. At this point, if your device
operates, programming is complete.
[ If the indicator light rapidly
flashes green, firmly press, hold
for two seconds and release the
HomeLink button up to three times
in a row slowly to complete the
programming process. Do not press
the HomeLink button rapidly. At
this point if your device operates,
programming is complete. If the
device does not operate, continue
with step 6.
6. At the garage door opener motor, (security gate motor, etc.) locate the
“Learn”, “Smart”, “Set” or “Program”
button. This can usually be found
where the hanging antenna wire is
attached to the motor-head unit (see
the device’s manual to identify this
button). The name and color of the
button may vary by manufacturer.
ODL3A040504
A: LEARN BUTTON
à A ladder and/or second person may
simplify the following steps.
7. Firmly press and release the “Learn”, “Smart”, “Set” or “Program” button.
You now have up to 30 seconds in
which to complete the next step.
8. Return to the vehicle and firmly press, hold for two seconds and release,
the HomeLink button up to three
times in a row slowly. Do not press
the HomeLink button rapidly. As soon
as you see the garage door start to
move, stop pressing any buttons
until a few seconds after the garage
door has come to a complete stop,
regardless of position. At this point,
programming is complete and your
device should operate when the
HomeLink button is pressed and
released.
Page 212 of 661
05
5-63
B0913EU04
To prevent the light sensors from
malfunctioning
To prevent the light sensors from
malfunctioning, do no
t touch or cover
them.
Digital mirror mode operating
condition
The START/STOP button is in the ON
position.
When the START/STOP button is
changed ignition switch LOCK/OFF
or ACC position, the image will be
disappeared.
When using the Digital Center Mirror
in digital mirror mode
[ When the liftgate is open, the Digital
Center Mirror image may not display
properly. Before driving, make sure
the liftgate is closed.
[ If the display is difficult to see due to
reflected light, close the sunshade for
the sunroof (if equipped).
[ Any of the following conditions may
occur when driving in the dark, such
as at night. None of them indicates
that the malfunction has occurred.
- Colors of objects in the displayed
image may differ their actual color.
- Depending on your physical
condition or age, it may take longer
than usual to focus on the displayed
image. In this case, change to
optical mirror mode.
- Do not let passengers stare at the
displayed image when the vehicle is
being driven, as doing so may cause
motion sickness.
Page 216 of 661
05
5-67
Power Windows
The ignition switch or Engine Start/Stop
button must be in the ON position to
be able to raise or lower the windows.
Each door has a Power Window switch
to control that door’s window. The
driver has a Power Window Lock button
which can block the operation of rear
passenger windows. The power windows
will operate for approximately 3 minutes
after the ignition switch or Engine Start/
Stop button is in the ACC or LOCK/
OFF position, as long as the front doors
remain closed.
If the front doors are opened, battery
power is turned OFF and the Power
Windows will not operate.
Information
[ In cold and wet climates, power
window may not work properly due to
freezing conditions.
[ While driving with the rear windows
down or with the sunroof (if equipped)
opened (or partially opened), your
vehicle may demonstrate a wind
buffeting or pulsation noise. This
noise is normal and can be reduced
or eliminated by taking the following
actions. If the noise occurs with one
or both of the rear windows down,
partially lower both front windows
approximately 1 inch (2.5 cm). If you
experience the noise with the sunroof
open, slightly close the sunroof.
Window opening and closing
B0142KO01
To open:
Press the window switch down to the
first detent position Q. Release the
switch when you want the window to
stop.
To close:
Pull the window switch up to the first
detent position Q. Release the window
switch when you want the window to
stop.
Page 217 of 661
Convenience Features5-68
Auto up/down window
Pressing or pulling up the power window
switch momentarily to the second
detent position R completely lowers or
lifts the window even when the switch
is released. To stop the window at the
desired position while the window is in
operation, pull up or press down and
release the switch.
WARNING
[ Do not leave the engine running
and the key in your vehicle with
unsupervised children. Unattended
children could operate the window,
which could result in serious injury.
[ Do not extend your head, arms or any
other body parts or objects outside
the window while driving to avoid
serious injury.
Resetting the power windows
If the power windows do not operate
normally, the automatic power window
system must be reset as follows:
1. Place the ignition switch or Engine
Start/Stop button to the ON position.
2. Close the window and continue pulling up on the power window
switch for at least one second.
If the power windows do not operate
properly after resetting, have the system
be inspected by an authorized HYUNDAI
dealer.
WARNING
The automatic reverse feature doesn’t
activate while resetting the power
window system.
Make sure body parts or other objects
are safely out of the way before closing
the windows to avoid injuries or vehicle
damage.
Automatic reverse
B0142KO02
If a window senses any obstacle while it
is closing automatically, it will stop and
lower approximately 12 in. (30 cm) to
allow the object to be cleared.
If the window detects the resistance
while the power window switch is
pulled up continuously, the window
will stop upward movement then lower
approximately 1 in. (2.5 cm).
If the power window switch is pulled
up continuously again within 5 seconds
after the window is lowered by the
automatic window reverse feature,
the automatic window reverse will not
operate.
Page 225 of 661
Convenience Features5-76
If your vehicle is equipped with a
sunroof, you can slide or tilt your sunroof
with the sunroof switch located on the
overhead console.
B0903EU02
A: Front, B: Rear
The sunroof can only be operated when
the ignition switch or Engine Start/Stop
button is in the ON or START position.
The sunroof can be operated for
approximately 30 seconds after the
ignition switch or Engine Start/Stop
button is in the ACC or LOCK/OFF
position.
However, if the front door is open, the
sunroof cannot be operated even within
the 3 minute period.
WARNING
[ Adjust the sunroof or sunshade when
your vehicle stops. This could result
in loss of control and an accident
that may cause injury, or property
damage.
[ Do not leave the engine running
and the key in your vehicle with
unsupervised children. Unattended
children could operate the sunroof,
which could result in serious injury.
[ Do not sit on the top of the vehicle. It
may cause injury or vehicle damage.
NOTICE
Do not operate the sunroof when roof
bars are installed on the vehicle or
when there is luggage on the roof.
Information
When the rear power window switches
are disabled using the power window lock
button, the rear sunroof operation switch
is also disabled. If you need to operate the
rear seat sunroof, operate the rear seat
sunroof with the front sunroof operation
switch.
' 8 $ / 6 8 1 5 2 2 )
Page 251 of 661
Convenience Features5-102
B0179KO01
Hight Beam Assist will automatically
switch between high beam and low
beam depending on the detected
brightness from the lamps of oncoming
vehicles or vehicles in front.
Detecting sensor
B0179KO02
M: front view camera
The front view camera is used as a
detecting sensor to detect ambient light
and brightness while driving.
Refer to the picture above for the
detailed location of the detecting sensor.
NOTICE
[ Always keep the front view camera in
good condition to maintain optimal
performance of High Beam Assist.
[ ) R U P R U H G H W D L O V R Q W K H S U H F D X W L R Q V
of the front view camera, refer to
U ) R U Z D U G & R O O L V L R Q $ Y R L G D Q F H $ V V L V W
) & $ V V H F W L R Q L Q F K D S W H U
High Beam Assist Settings
B0179EU03
With the ignition switch or the Engine
Start/Stop button in the ON position,
V H O H F W S / L J K W V
Page 254 of 661
05
5-105
INTERIOR LIGHTS
WARNING
Do not use the interior lights when
driving in the dark. The interior lights
may obscure your view and cause an
accident.
NOTICE
Do not use the interior lights for
extended periods when the vehicle is
turned off or the battery will discharge.
Interior Lamp AUTO Off
The interior lamps will automatically go
off approximately 20 minutes after the
vehicle is turned off and the doors are
closed. If a door is opened, the lamp
will go off 25 minutes after the vehicle
is turned off. If the doors are locked by
the smart key and the vehicle enters the
armed stage of the theft alarm system,
the lamps will go off five seconds later.
) U R Q W / D P S V
B0903EU03
Front map lamp ():
Touch either icons to turn the map lamp
on or off. This light produces a spot
beam for convenient use as a map lamp
at night or as a personal lamp for the
driver and the front passenger.
Door lamp ( ):
The front or rear room lamps come on
when the front or rear doors are opened.
When doors are unlocked by the smart
key, the front and rear lamps come on
for approximately 30 seconds as long as
any door is not opened. The front and
rear room lamps go out gradually after
approximately 30 seconds when the door
is closed. However, if the ignition switch
or Engine Start/Stop button is in the ON
position or all doors are locked, the front
and rear lamps will turn off. If a door is
opened with the ignition switch in the
ACC position or the LOCK/OFF position,
the front and rear lamps will stay on for
about 5 minutes.
Room lamp (()
Press the button to turn ON the room
lamp for the front and rear seats.
Page 259 of 661
Convenience Features5-110
B0200KO01
) U R Q W : L Q G V K L H O G : L S H U V
Operates as follows when the ignition
switch or Engine Start/Stop button is in
the ON position.
MIST: For a single wiping cycle, push the lever upward and release. The
wipers will operate continuously
if the lever is held in this position.
OFF: Wiper is not in operation.
AUTO
(if equipped): The rain sensor located
on the upper end of the
windshield glass senses
the amount of rainfall and
controls the wiping cycle
for the proper interval. The
more it rains, the faster
the wiper operates. When
the rain stops, the wiper
stops. To vary the speed
setting, turn the speed
control knob.
LO: The wiper runs at a lower speed.
HI: The wiper runs at a higher speed.
Information
If there is heavy accumulation of snow
or ice on the windshield, defrost the
windshield for about 10 minutes, or until
the snow and/or ice is removed before
using the windshield wipers to ensure
proper operation.
If you do not remove the snow and/or ice
before using the wiper and washer, it may
damage the wiper and washer system.
AUTO wiper control (if equipped)
B0200KO02
The rain sensor located on the upper
end of the windshield glass senses
the amount of rainfall and controls the
wiping cycle for the proper interval.
The wiper operation time will be
automatically controlled depends on
rainfall.
When the rain stops, the wiper stops.
To vary the sensitivity setting, turn the
sensitivity control knob.
If the wiper switch is set in AUTO mode
when the ignition switch is in the ON
position, the wiper will operate once to
perform a self-check of the system. Set
the wiper to the OFF position when the
wiper is not in use.
WIPERS AND WASHERS
Page 298 of 661
05
5-149
Rear Window DefrosterNOTICE
To prevent damage to the rear window
defroster conducting elements bonded
to the inside surface of the rear window,
never use sharp instruments or window
cleaners containing abrasives to clean
the window.
If you want to defrost and defog
the front windshield, refer to the
U : L Q G V K L H O G ' H I U R V W L Q J D Q G ' H I R J J L Q JV
section in this chapter.
The defroster heats the
window to remove frost, fog
and thin ice from the interior
and exterior of the rear
window, while the engine is
running.
[ To activate the rear window defroster,
press the rear window defroster
button located in the center control
panel. The indicator on the rear
window defroster button illuminates
when the defroster is ON.
[ To turn off the defroster, press the rear
window defroster button again.
Information
[ If there is heavy accumulation of snow
on the rear window, brush it off before
operating the rear defroster.
[ The rear window defroster
automatically turns off after
approximately 20 minutes or when the
ignition switch or Engine Start/Stop
button is in the LOCK/OFF position.
Side view mirror defroster
If your vehicle is equipped with the side
view mirror defrosters, they will operate
at the same time you turn on the rear
window defroster.
Page 304 of 661
05
5-155
WARNING
[ Avoid abrupt starting and braking
when the cup holder is in use to
prevent spilling your drink. If hot
liquid spills, you could be burned.
Such a burn to the driver could cause
loss of vehicle control resulting in an
accident.
[ Do not place uncovered or unsecured
cups, bottles, cans, etc., in the cup
holder containing hot liquid while
the vehicle is in motion. Injuries may
result in the event of a sudden stop
or collision.
[ Only use soft cups in the cup holders.
Hard objects can injure you in an
accident.
WARNING
Keep cans or bottles out of direct sun
light and do not put them in a hot
vehicle. It may explode.
NOTICE
[ Keep your drinks sealed while
driving to prevent spilling your drink.
If liquid spills, it may get into the
vehicle’s electrical/electronic system
and damage electrical/electronic
parts.
[ When cleaning spilled liquids do not
use hot air to blow out or dry the cup
holder. This may damage the interior.