Power supply INFINITI FX35 2004 Owner's Manual

TROUBLE DIAGNOSIS
AT-47
D
E
F
G
H
I
J
K
L
MA
B
AT
Revision: 2004 November 2004 FX35/FX45
4❏ Execute all road tests and enter checks in required inspection items.AT- 5 4
4-1.Check before engine is started
AT- 5 5
❏ The A/T CHECK Indicator Lamp does come on. AT- 1 9 1 .
❏ Perform self-diagnostics. Enter checks for detected items. AT- 9 4
, AT-103
❏ AT-105, "DTC U1000 CAN COMMUNICATION LINE" .
❏ AT-108, "
DTC P0615 START SIGNAL CIRCUIT" .
❏ AT-112, "
DTC P0705 PARK/NEUTRAL POSITION SWITCH" .
❏ AT-116, "
DTC P0720 VEHICLE SPEED SENSOR A/T (REVOLUTION SENSOR)" .
❏ AT-121, "
DTC P0725 ENGINE SPEED SIGNAL" .
❏ AT-121, "
DTC P0725 ENGINE SPEED SIGNAL" .
❏ AT-123, "
DTC P0740 TORQUE CONVERTER CLUTCH SOLENOID VALVE" .
❏ AT-125, "
DTC P0744 A/T TCC S/V FUNCTION (LOCK-UP)" .
❏ AT-127, "
DTC P0745 LINE PRESSURE SOLENOID VALVE" .
❏ AT-129, "
DTC P1701 TRANSMISSION CONTROL MODULE (POWER SUPPLY)" .
❏ AT-133, "
DTC P1702 TRANSMISSION CONTROL MODULE (RAM)" .
❏ AT-134, "
DTC P1703 TRANSMISSION CONTROL MODULE (ROM)" .
❏ AT-135, "
DTC P1704 TRANSMISSION CONTROL MODULE (EEPROM)" .
❏ AT-136, "
DTC P1705 THROTTLE POSITION SENSOR" .
❏ AT-139, "
DTC P1710 A/T FLUID TEMPERATURE SENSOR CIRCUIT" .
❏ AT-143, "
DTC P1716 TURBINE REVOLUTION SENSOR" .
❏ AT-145, "
DTC P1721 VEHICLE SPEED SENSOR MTR" .
❏ AT-147, "
DTC P1730 A/T INTERLOCK" .
❏ AT-150, "
DTC P1731 A/T 1ST ENGINE BRAKING" .
❏ AT-152, "
DTC P1752 INPUT CLUTCH SOLENOID VALVE" .
❏ AT-154, "
DTC P1754 INPUT CLUTCH SOLENOID VALVE FUNCTION" .
❏ AT-156, "
DTC P1757 FRONT BRAKE SOLENOID VALVE" .
❏ AT-158, "
DTC P1759 FRONT BRAKE SOLENOID VALVE FUNCTION" .
❏ AT-160, "
DTC P1762 DIRECT CLUTCH SOLENOID VALVE" .
❏ AT-162, "
DTC P1764 DIRECT CLUTCH SOLENOID VALVE FUNCTION" .
❏ AT-164, "
DTC P1767 HIGH AND LOW REVERSE CLUTCH SOLENOID VALVE" .
❏ AT-166, "
DTC P1769 HIGH AND LOW REVERSE CLUTCH SOLENOID VALVE
FUNCTION" .
❏ AT-168, "
DTC P1772 LOW COAST BRAKE SOLENOID VALVE" .
❏ AT-170, "
DTC P1774 LOW COAST BRAKE SOLENOID VALVE FUNCTION" .
❏ AT-172, "
DTC P1815 MANUAL MODE SWITCH" .
❏ AT-178, "
DTC P1841 ATF PRESSURE SWITCH 1" .
❏ AT-180, "
DTC P1843 ATF PRESSURE SWITCH 3" .
❏ AT-182, "
DTC P1845 ATF PRESSURE SWITCH 5" .
❏ AT-184, "
DTC P1846 ATF PRESSURE SWITCH 6" .
4-2.Check at Idle
AT- 5 5
❏ AT- 1 9 3 , "Engine Cannot Be Started In “P” or “N” Position" .
❏ AT- 1 9 3 , "
In “P” Position, Vehicle Moves When Pushed" .
❏ AT- 1 9 4 , "
In “N” Position, Vehicle Moves" .
❏ AT- 1 9 5 , "
Large Shock (“N” to “D” Position)" .
❏ AT- 1 9 8 , "
Vehicle Does Not Creep Backward In “R” Position" .
❏ AT- 2 0 1 , "
Vehicle Does Not Creep Forward In “D” Position" .
4-3.Cruise test
AT- 5 7
Part 1
❏ AT- 2 0 3 , "
Vehicle Cannot Be Started From D1" .
❏ AT- 2 0 6 , "
A/T Does Not Shift: D1 → D2" .
❏ AT- 2 0 8 , "
A/T Does Not Shift: D2 → D3" .
❏ AT- 2 11 , "
A/T Does Not Shift: D3 → D4" .
❏ AT- 2 1 3 , "
A/T Does Not Shift: D4 → D5" .
❏ AT- 2 1 6 , "
A/T Does Not Perform Lock-up"
❏ AT- 2 1 8 , "A/T Does Not Hold Lock-up Condition" .
❏ AT- 2 2 0 , "
Lock-up Is Not Released" .
❏ AT- 2 2 1 , "
Engine Speed Does Not Return To Idle" .

AT-48
TROUBLE DIAGNOSIS
Revision: 2004 November 2004 FX35/FX45
44-3Part 2
AT- 6 0
❏ AT-203, "Vehicle Cannot Be Started From D1" .
❏ AT-206, "
A/T Does Not Shift: D1 → D2" .
❏ AT-208, "
A/T Does Not Shift: D2 → D3" .
❏ AT- 2 11 , "
A/T Does Not Shift: D3 → D4" .
Part 3
AT- 6 1
❏ AT-222, "Cannot Be Changed to Manual Mode" .
❏ AT-223, "
A/T Does Not Shift: 5th gear → 4th gear" .
❏ AT-225, "
A/T Does Not Shift: 4th gear → 3rd gear" .
❏ AT-227, "
A/T Does Not Shift: 3rd gear → 2nd gear" .
❏ AT-229, "
A/T Does Not Shift: 2nd gear → 1st gear" .
❏ AT-231, "
Vehicle Does Not Decelerate By Engine Brake" .
❏ Perform self-diagnostics. Enter checks for detected items. AT- 9 4
, AT-103
❏ AT-105, "DTC U1000 CAN COMMUNICATION LINE" .
❏ AT-108, "
DTC P0615 START SIGNAL CIRCUIT" .
❏ AT- 11 2 , "
DTC P0705 PARK/NEUTRAL POSITION SWITCH" .
❏ AT- 11 6 , "
DTC P0720 VEHICLE SPEED SENSOR A/T (REVOLUTION SENSOR)" .
❏ AT-121, "
DTC P0725 ENGINE SPEED SIGNAL" .
❏ AT-121, "
DTC P0725 ENGINE SPEED SIGNAL" .
❏ AT-123, "
DTC P0740 TORQUE CONVERTER CLUTCH SOLENOID VALVE" .
❏ AT-125, "
DTC P0744 A/T TCC S/V FUNCTION (LOCK-UP)" .
❏ AT-127, "
DTC P0745 LINE PRESSURE SOLENOID VALVE" .
❏ AT-129, "
DTC P1701 TRANSMISSION CONTROL MODULE (POWER SUPPLY)" .
❏ AT-133, "
DTC P1702 TRANSMISSION CONTROL MODULE (RAM)" .
❏ AT-134, "
DTC P1703 TRANSMISSION CONTROL MODULE (ROM)" .
❏ AT-135, "
DTC P1704 TRANSMISSION CONTROL MODULE (EEPROM)" .
❏ AT-136, "
DTC P1705 THROTTLE POSITION SENSOR" .
❏ AT-139, "
DTC P1710 A/T FLUID TEMPERATURE SENSOR CIRCUIT" .
❏ AT-143, "
DTC P1716 TURBINE REVOLUTION SENSOR" .
❏ AT-145, "
DTC P1721 VEHICLE SPEED SENSOR MTR" .
❏ AT-147, "
DTC P1730 A/T INTERLOCK" .
❏ AT-150, "
DTC P1731 A/T 1ST ENGINE BRAKING" .
❏ AT-152, "
DTC P1752 INPUT CLUTCH SOLENOID VALVE" .
❏ AT-154, "
DTC P1754 INPUT CLUTCH SOLENOID VALVE FUNCTION" .
❏ AT-156, "
DTC P1757 FRONT BRAKE SOLENOID VALVE" .
❏ AT-158, "
DTC P1759 FRONT BRAKE SOLENOID VALVE FUNCTION" .
❏ AT-160, "
DTC P1762 DIRECT CLUTCH SOLENOID VALVE" .
❏ AT-162, "
DTC P1764 DIRECT CLUTCH SOLENOID VALVE FUNCTION" .
❏ AT-164, "
DTC P1767 HIGH AND LOW REVERSE CLUTCH SOLENOID VALVE" .
❏ AT-166, "
DTC P1769 HIGH AND LOW REVERSE CLUTCH SOLENOID VALVE
FUNCTION" .
❏ AT-168, "
DTC P1772 LOW COAST BRAKE SOLENOID VALVE" .
❏ AT-170, "
DTC P1774 LOW COAST BRAKE SOLENOID VALVE FUNCTION" .
❏ AT-172, "
DTC P1815 MANUAL MODE SWITCH" .
❏ AT-178, "
DTC P1841 ATF PRESSURE SWITCH 1" .
❏ AT-180, "
DTC P1843 ATF PRESSURE SWITCH 3" .
❏ AT-182, "
DTC P1845 ATF PRESSURE SWITCH 5" .
❏ AT-184, "
DTC P1846 ATF PRESSURE SWITCH 6" .
5❏ Inspect each system for items found to be NG in the self-diagnostics and repair or replace the malfunction
parts.
6❏ Perform all road tests and enter the checks again for the required items.AT- 5 4
7❏ For any remaining NG items, perform the “diagnostics procedure” and repair or replace the malfunction parts.
See the chart for diagnostics by symptoms. (This chart also contains other symptoms and inspection proce-
dures.)AT- 6 5
8❏ Erase the results of the self-diagnostics from the TCM.AT- 4 0,
AT- 1 0 4

AT-90
TROUBLE DIAGNOSIS
Revision: 2004 November 2004 FX35/FX45
TCM Input/Output Signal Reference ValuesACS007AH
A/T ASSEMBLY HARNESS CONNECTOR TERMINAL LAYOUT
TCM INSPECTION TABLE
Data are reference value and are measured between each terminal and ground.
SCIA1658E
TerminalWire
colorItem Condition Data (Approx.)
1LGPower supply
(Memory back-up)Always Battery voltage
2LGPower supply
(Memory back-up)Always Battery voltage
3 L CAN-H – –
4PUK-line (CONSULT-
II signal)The terminal is connected to the data link connector for CONSULT-II. –
5 B Ground Always 0V
6 Y Power supply– Battery voltage
–0V
7ORBack-up lamp
relaySelector lever in “R” position. 0V
Selector lever in other positions. Battery voltage
8 R CAN-L – –
9GYStarter relaySelector lever in “N” and “P” positions. Battery voltage
Selector lever in other positions. 0V
10 B Ground Always 0V

AT-94
TROUBLE DIAGNOSIS
Revision: 2004 November 2004 FX35/FX45
SELF-DIAGNOSTIC RESULT MODE
Operation Procedure
1. Perform “CONSULT-II SETTING PROCEDURE” Refer to AT- 9 3 ,
"CONSULT-II SETTING PROCEDURE" .
2. Touch “SELF-DIAG RESULTS”.
Display shows malfunction experienced since the last erasing
operation.
Display Items List
X: Applicable, —: Not applicable
SCIA5304E
Items (CONSULT-
II screen terms)Malfunction is detected when...TCM self-diagnosis OBD-II (DTC)
A/T CHECK
indicator
lamp “A/T” with
CONSULT-IIMIL indicator
lamp*1,
“ENGINE” with
CONSULT-II or
GST
CAN COMM CIR-
CUIT

When a malfunction is detected in CAN communications X U1000 U1000
STARTER RELAY/
CIRC

If this signal is ON other than in P or N position, this is
judged to be a malfunction.
(And if it is OFF in P or N position, this too is judged to be a
malfunction.)X P0615 —
PNP SW/CIRC

PNP switch 1-4 signals input with impossible pattern

P position is detected from N position without any other
position being detected in between.X P0705 P0705
VEH SPD SEN/
CIR AT (Revolution
sensor)

Signal from vehicle speed sensor A/T (Revolution sensor)
not input due to cut line or the like

Unexpected signal input during running

After ignition switch is turned ON, unexpected signal input
from vehicle speed sensor MTR before the vehicle starts
movingX P0720 P0720
ENGINE SPEED
SIG

TCM does not receive the CAN communication signal from
the ECM.X P0725 P0725*3
TCC SOLENOID/
CIRC

Normal voltage not applied to solenoid due to cut line,
short, or the likeX P0740 P0740
A/T TCC S/V
FNCTN

A/T cannot perform lock-up even if electrical circuit is good.

TCM detects as irregular by comparing difference value
with slip rotation.X P0744 P0744*2
L/PRESS SOL/
CIRC

Normal voltage not applied to solenoid due to cut line,
short, or the like

TCM detects as irregular by comparing target value with
monitor value.X P0745 P0745
TCM-POWER
SUPPLY

When the power supply to the TCM is cut “OFF”, for exam-
ple because the battery is removed, and the self-diagnos-
tics memory function stops

This is not a malfunction message (Whenever shutting
“OFF” a power supply to the TCM, this message appears
on the screen.)— P1701 —
TCM·RAM

TCM memory (RAM) is malfunctioning. — P1702 —
TCM·ROM

TCM memory (ROM) is malfunctioning. — P1703 —

AT-114
DTC P0705 PARK/NEUTRAL POSITION SWITCH
Revision: 2004 November 2004 FX35/FX45
Diagnostic ProcedureACS007B3
1. CHECK PNP SW CIRCUIT
With CONSULT-II
1. Turn ignition switch “ON”. (Do not start engine.)
2. Select “MAIN SIGNALS” in “DATA MONITOR” mode for “A/T”
with CONSULT-II.
3. Read out “N/P”, “R” and “D” position switches moving selector
lever to each position.
OK or NG
OK >> GO TO 5.
NG >> GO TO 2.
2. CHECK TCM
Perform TCM input/output signals inspection. Refer to AT- 9 0 , "
TCM Input/Output Signal Reference Values" .
OK or NG
OK >> GO TO 3.
NG >> GO TO 4.
3. CHECK TERMINAL CORD ASSEMBLY
1. Remove control valve with TCM. Refer to AT- 2 4 2 , "
Control Valve with TCM and A/T Fluid Temperature
Sensor 2" .
2. Disconnect A/T assembly harness connector and control valve with TCM harness connector.
3. Check continuity between A/T assembly harness connector terminal and control valve with TCM harness
connector terminal. Refer to AT- 11 3 , "
Wiring Diagram — AT — PNP/SW" .
4. If OK, check harness for short to ground and short to power.
OK or NG
OK >> Replace the control valve with TCM. Refer to AT- 2 4 2 , "Control Valve with TCM and A/T Fluid Tem-
perature Sensor 2" .
NG >> Replace open circuit or short to ground and short to power in harness or connectors.
4. DETECT MALFUNCTIONING ITEM
Check the following items:

Harness for short or open between battery and A/T assembly harness connector terminals 1, 2

Harness for short or open between ignition switch and A/T assembly harness connector terminal 6

10A fuse (No. 37, located in the fuse and fusible link block) and 10A fuse (No. 83, located in the IPDM E/
R).

Ignition switch, Refer to PG-3, "POWER SUPPLY ROUTING CIRCUIT" .
OK or NG
OK >> GO TO 5.
NG >> Repair or replace damaged parts.
Item name Condition Display value
SLCTLVR POSISelector lever in “N” and “P” positions. N/P
Selector lever in “R” position. R
Selector lever in “D” position. D
SCIA5296E

DTC P0720 VEHICLE SPEED SENSOR A/T (REVOLUTION SENSOR)
AT-119
D
E
F
G
H
I
J
K
L
MA
B
AT
Revision: 2004 November 2004 FX35/FX45
Diagnostic ProcedureACS007BA
1. CHECK INPUT SIGNALS
With CONSULT-II
1. Turn ignition switch “ON”. (Do not start engine.)
2. Select “ECU INPUT SIGNALS” in “DATA MONITOR” mode for
“A/T” with CONSULT-II.
3. Start the engine.
4. Read out the value of “VHCL/S SE·A/T” while driving.
Check the value changes according to driving speed.
OK or NG
OK >> GO TO 5.
NG >> GO TO 2.
2. CHECK TCM
Perform TCM input/output signals inspection. Refer to AT- 9 0 , "
TCM Input/Output Signal Reference Values" .
OK or NG
OK >> GO TO 3.
NG >> GO TO 4.
3. CHECK TERMINAL CORD ASSEMBLY
1. Remove control valve with TCM. Refer to AT- 2 4 2 , "
Control Valve with TCM and A/T Fluid Temperature
Sensor 2" .
2. Disconnect A/T assembly harness connector and control valve with TCM harness connector.
3. Check continuity between A/T assembly harness connector terminal and control valve with TCM harness
connector terminal. Refer to AT- 11 8 , "
Wiring Diagram — AT — VSSA/T" .
4. If OK, check harness for short to ground and short to power.
OK or NG
OK >> GO TO 5.
NG >> Replace open circuit or short to ground and short to power in harness or connectors.
4. DETECT MALFUNCTIONING ITEM
Check the following items:

Harness for short or open between battery and A/T assembly harness connector terminals 1, 2

Harness for short or open between ignition switch and A/T assembly harness connector terminal 6

10A fuse (No. 37, located in the fuse and fusible link block) and 10A fuse (No. 83, located in the IPDM E/
R).

Ignition switch, Refer to PG-3, "POWER SUPPLY ROUTING CIRCUIT" .
OK or NG
OK >> GO TO 6.
NG >> Repair or replace damaged parts.
Item name Condition Display value (km/h)
VHCL/S SE·A/T During drivingApproximately matches the
speedometer reading.
SCIA2148E

AT-122
DTC P0725 ENGINE SPEED SIGNAL
Revision: 2004 November 2004 FX35/FX45
2. CHECK DTC WITH TCM
With CONSULT-II
1. Start engine.
2. Select “ECU INPUT SIGNALS” in “DATA MONITOR” mode for
“A/T” with CONSULT-II.
3. While monitoring engine speed, check for engine speed change
corresponding to wide-open throttle position signal.
With GST
Follow the procedure “With CONSULT-II”.
OK or NG
OK >> GO TO 3.
NG >> Check the ignition signal circuit.

Refer to EC-585, "IGNITION SIGNAL" (for VQ35DE) or EC-1262, "IGNITION SIGNAL" (for
VK45DE).
3. CHECK DTC
Perform “DTC Confirmation Procedure”.

Refer to AT- 1 2 1 , "DTC Confirmation Procedure" .
OK or NG
OK >>INSPECTION END
NG >> GO TO 4.
4. CHECK SELF-DIAGNOSTIC RESULTS
Perform self-diagnosis. Refer to AT- 9 4 , "
SELF-DIAGNOSTIC RESULT MODE" .
Do the self-diagnostic results indicate
“TCM-POWER SUPPLY”?
YES >> Check the TCM power circuit. Refer to AT- 1 2 9 , "DTC P1701 TRANSMISSION CONTROL MOD-
ULE (POWER SUPPLY)" .
NO >> GO TO 5.
5. DETECT MALFUNCTIONING ITEM
Check the following items:

The A/T assembly harness connector terminals for damage or loose connection with harness connector.
OK or NG
OK >> Replace the control valve with TCM. Refer to AT- 2 4 2 , "Control Valve with TCM and A/T Fluid Tem-
perature Sensor 2" .
NG >> Repair or replace damaged parts.
Item name Condition Display value (rpm)
ENGINE SPEED Engine running Closely matches the tachometer reading.
PCIA0041E

AT-124
DTC P0740 TORQUE CONVERTER CLUTCH SOLENOID VALVE
Revision: 2004 November 2004 FX35/FX45
Diagnostic ProcedureACS007BN
1. CHECK INPUT SIGNALS
With CONSULT-II
1. Turn ignition switch “ON”. (Do not start engine.)
2. Select “MAIN SIGNALS” in “DATA MONITOR” mode for “A/T”
with CONSULT-II.
3. Start the engine.
4. Read out the value of “TCC SOLENOID” while driving.
OK or NG
OK >> GO TO 4.
NG >> GO TO 2.
2. CHECK SELF-DIAGNOSTIC RESULTS
Perform self-diagnosis. Refer to AT- 9 4 , "
SELF-DIAGNOSTIC RESULT MODE" .
Do the self-diagnostic results indicate
“TCM-POWER SUPPLY”?
YES >> Check the TCM power circuit. Refer to AT- 1 2 9 , "DTC P1701 TRANSMISSION CONTROL MOD-
ULE (POWER SUPPLY)" .
NO >> GO TO 3.
3. DETECT MALFUNCTIONING ITEM
Check the following items:

The A/T assembly harness connector terminals for damage or loose connection with harness connector.
OK or NG
OK >> Replace the control valve with TCM. Refer to AT- 2 4 2 , "Control Valve with TCM and A/T Fluid Tem-
perature Sensor 2" .
NG >> Repair or replace damaged parts.
4. CHECK DTC
Perform “DTC Confirmation Procedure”.

Refer to AT- 1 2 3 , "DTC Confirmation Procedure" .
OK or NG
OK >>INSPECTION END
NG >> GO TO 2.
Item name Condition Display value (Approx.)
TCC SOLENOIDWhen performing slip lock-up 0.2 - 0.4 A
When performing lock-up 0.4 - 0.6 A
SCIA4793E

AT-126
DTC P0744 A/T TCC S/V FUNCTION (LOCK-UP)
Revision: 2004 November 2004 FX35/FX45
WITH GST
Follow the procedure “With CONSULT-II”.
Diagnostic ProcedureACS007BT
1. CHECK INPUT SIGNALS
With CONSULT-II
1. Turn ignition switch “ON”. (Do not start engine.)
2. Select “MAIN SIGNALS” in “DATA MONITOR” mode for “A/T”
with CONSULT-II.
3. Start the engine.
4. Read out the value of “TCC SOLENOID” while driving.
OK or NG
OK >> GO TO 4.
NG >> GO TO 2.
2. CHECK SELF-DIAGNOSTIC RESULTS
Perform self-diagnosis. Refer to AT- 9 4 , "
SELF-DIAGNOSTIC RESULT MODE" .
Do the self-diagnostic results indicate
“TCM-POWER SUPPLY”?
YES >> Check the TCM power circuit. Refer to AT- 1 2 9 , "DTC P1701 TRANSMISSION CONTROL MOD-
ULE (POWER SUPPLY)" .
NO >> GO TO 3.
3. DETECT MALFUNCTIONING ITEM
Check the following items:

The A/T assembly harness connector terminals for damage or loose connection with harness connector.
OK or NG
OK >> Replace the control valve with TCM. Refer to AT- 2 4 2 , "Control Valve with TCM and A/T Fluid Tem-
perature Sensor 2" .
NG >> Repair or replace damaged parts.
4. CHECK DTC
Perform “DTC Confirmation Procedure”.

Refer to AT- 1 2 5 , "DTC Confirmation Procedure" .
OK or NG
OK >>INSPECTION END
NG >> GO TO 2.
Item name Condition Display value (Approx.)
TCC SOLENOIDWhen performing slip lock-up 0.2 - 0.4 A
When performing lock-up 0.4 - 0.6 A
SCIA4793E

AT-128
DTC P0745 LINE PRESSURE SOLENOID VALVE
Revision: 2004 November 2004 FX35/FX45
Diagnostic ProcedureACS007BZ
1. CHECK INPUT SIGNALS
With CONSULT-II
1. Turn ignition switch “ON”. (Do not start engine.)
2. Select “MAIN SIGNALS” in “DATA MONITOR” mode for “A/T”
with CONSULT-II.
3. Start the engine.
4. Read out the value of “LINE PRES SOL” while driving.
OK or NG
OK >> GO TO 4.
NG >> GO TO 2.
2. CHECK SELF-DIAGNOSTIC RESULTS
Perform self-diagnosis. Refer to AT- 9 4 , "
SELF-DIAGNOSTIC RESULT MODE" .
Do the self-diagnostic results indicate
“TCM-POWER SUPPLY”?
YES >> Check the TCM power circuit. Refer to AT- 1 2 9 , "DTC P1701 TRANSMISSION CONTROL MOD-
ULE (POWER SUPPLY)" .
NO >> GO TO 3.
3. DETECT MALFUNCTIONING ITEM
Check the following items:

The A/T assembly harness connector terminals for damage or loose connection with harness connector.
OK or NG
OK >> Replace the control valve with TCM. Refer to AT- 2 4 2 , "Control Valve with TCM and A/T Fluid Tem-
perature Sensor 2" .
NG >> Repair or replace damaged parts.
4. CHECK DTC
Perform “DTC Confirmation Procedure”.

Refer to AT- 1 2 7 , "DTC Confirmation Procedure" .
OK or NG
OK >>INSPECTION END
NG >> GO TO 2.
Item name Condition Display value (Approx.)
LINE PRES SOL During driving 0.2 - 0.6 A
SCIA4793E