parking brake INFINITI FX35 2005 Service Manual

ABCDEFGHIJKMLQUICK REFERENCE INDEX AGENERAL INFORMATIONGIGeneral InformationBENGINEEMEngine MechanicalLUEngine Lubrication SystemCOEngine Cooling SystemECEngine Control SystemFLFuel SystemEXExhaust SystemACCAccelerator Control SystemCTRANSMISSION/
TRANSAXLEATAutomatic TransmissionDDRIVELINE/AXLETFTransferPRPropeller ShaftFFDFront Final DriveRFDRear Final DriveFAXFront AxleRAXRear AxleESUSPENSIONFSUFront SuspensionRSURear SuspensionWTRoad Wheels & TiresFBRAKESBRBrake SystemPBParking Brake SystemBRCBrake Control SystemGSTEERINGPSPower Steering SystemHRESTRAINTSSBSeat BeltsSRSSupplemental Restraint System
(SRS)IBODYBLBody, Lock & Security SystemGWGlasses, Window System & Mir-
rorsRFRoofEIExterior & InteriorIPInstrument PanelSESeatJAIR CONDITIONERATCAutomatic Air ConditionerKELECTRICALSCStarting & Charging SystemLTLighting SystemDIDriver Information SystemWWWiper, Washer & HornBCSBody Control SystemLANLAN SystemAVAudio Visual, Navigation & Tele-
phone SystemACSAuto Cruise Control SystemPGPower Supply, Ground & Circuit Ele-
mentsLMAINTENANCEMAMaintenanceMINDEXIDXAlphabetical IndexEdition: August 2004
Revision: July 2005

DESCRIPTION ACS-7
[ICC]
C
D E
F
G H
I
J
L
M A
B
ACS
Revision: 2005 July 2005 FX
Components DescriptionAKS00C8D
CAN CommunicationAKS00C8E
CAN (Controller Area Network) is a serial communication line for real time application. It is an on-vehicle mul-
tiplex communication line with high data communication speed and excellent error detection ability. Many elec-
tric control units are equipped onto a vehicle, and each control unit shares information and links with other
control units during operation (not independent). In CAN communication, control units are connected with 2
communication lines (CAN H line, CAN L line) allowing a high rate of information transmission with less wiring.
Each control unit transmits/receives data but selectively reads required data only.
CAN COMMUNICATION UNIT
Refer to LAN-30, "CAN Communication Unit" .
Component Vehicle-to-
vehicle
distance
control mode Conventional
(fixed speed) cruise
control mode Brake assist
(with pre-
view func- tion) Description
ICC unit ××× Operates electric throttle control actuator and brake
booster based on that sensor signals and CAN commu-
nication data, then controls vehicle distance.
ICC sensor ×× Irradiates laser beam, and receives reflected laser
beam to measure distance from preceding vehicle.
ECM ××× Transmits throttle position signal and ICC steering
switch signal to ICC unit through CAN communication.
ABS actuator and electric
unit (control unit) ×××
Transmits wheel speed sensor signal to ICC unit
through CAN communication.
Brake pressure sensor ×× Detects fluid pressure in master cylinder.
Brake booster ×× Adjusts brake fluid pressure, based on command from
ICC unit.
BCM × Transmit front wiper request signal to ICC unit through
CAN communication.
TCM ×× Transmits gear position signal and output shaft revolu-
tion signal to ICC unit through CAN communication.
Unified meter and A/C amp. ××× Receives ICC system display signal, ICC warning lamp
signal and buzzer output signal from ICC unit through
CAN communication.
ICC brake switch, stop
lamp switch ××× Transmit operating signal to ICC unit when touching
brake pedal. ICC unit cancels cruise system at driver's
brake operation.
Parking brake switch ×× The cruise system is cancelled when applied.

ACS-12
[ICC]
LASER BEAM AIMING ADJUSTMENT
Revision: 2005 July 2005 FX
LASER BEAM AIMING ADJUSTMENTPFP:00026
OutlineAKS006YI
Adjust the laser beam aiming every time the ICC sensor is removed or installed.
CAUTION:

Place the vehicle on the level ground when the laser beam aiming adjustment is operated.

Follow the CONSULT-II when adjusting the laser beam aiming (laser beam aiming adjustment can-
not be operated without CONSULT-II).
PreparationAKS006YJ

Adjust the tire pressure to the specified value.

See that there is no load in the vehicle.

Coolant, engine oil filled up to correct level and full fuel tank.

Shift the gear into “P” position and release the parking brake.

Clean the ICC sensor with a soft cloth.
Outline of Adjustment ProcedureAKS006YK
1. Set up the ICC target board [KV99110100 (J-45718)].
2. Adjust the sensor following the procedure on CONSULT-II. (Turn manually the screw for up-down position adjustment. ICC sensor automatically adjust the right-left position.)
Setting the ICC Target BoardAKS006YL
Accurate ICC target board setting is required for the laser beam aiming adjustment.
CAUTION:
ICC system does not function normally if laser beam aiming is not accurate.
ADJUSTING HEIGHT OF THE TARGET
1. Attach a triangle scale at the center.
SKIA6179E
SKIA5974E

ACS-28
[ICC]
TERMINALS AND REFERENCE VALUE
Revision: 2005 July 2005 FX
Terminals and Reference Value for ICC SensorAKS00C8J
40(PU/W)
Ground Parking brake signal ON
Depress the parking brake Approx. 0
Release the parking brake Approx. 12
47 (W/R) Stop lamp drive output signal ON Brake operating with ICC system Approx.12
Brake not operating with ICC
system Approx. 0
Terminals
(Wire color) Item Condition
Voltage (V)
+– Ignition
switch Operation
Terminals
(Wire color) Item Condition
Voltage (V)
+– Ignition
switch Operation
1(Y)
Ground ICC sensor power ON — Battery voltage
3 (L) CAN H — — —
4 (B) Ground — — Approx. 0
6 (R) CAN L — — —

TROUBLE DIAGNOSIS — GENERAL DESCRIPTION ACS-31
[ICC]
C
D E
F
G H
I
J
L
M A
B
ACS
Revision: 2005 July 2005 FX
6. Touch any of “WORK SUPPORT”, “SELF-DIAG RESULTS”,
“DATA MONITOR”, “CAN DIAG SUPPORT MNTR”, “ACTIVE
TEST” and “ECU PART NUMBER” on selection screen.
WORK SUPPORT
Work Item
Cause of Auto-Cancel
1. Touch “WORK SUPPORT” on the “SELECT DIAG MODE” screen. Refer to ACS-30, "
CONSULT-II BASIC OPERATION" .
2. Touch “CAUSE OF AUTO-CANCEL” on the “SELECT WORK ITEM” screen.
3. Cause of automatic cancellation screen will be shown. CAUTION:
Last five cancel (system cancel) causes are displayed.
Display Item List
Laser Beam Adjust
For details, refer to ACS-12, "LASER BEAM AIMING ADJUSTMENT" .
PKIA8867E
Operation Function
CAUSE OF AUTO-CANCEL Indicates causes of automatic cancellation of the ICC system.
LASER BEAM ADJUST Outputs laser beam, calculates dislocation of the beam, and indicates adjustment direction.
SKIA6191E
Cause of cancellation Description
OPERATING WIPER Windshield wipers were operated at HI or LO speed operation.
OPERATING ABS ABS function was operated.
OPERATING TCS TCS function was operated.
OPERATING VDC VDC function was operated.
OPE SW VOLT CIRC Outside the standard control switch input voltage was detected.
ECM CIRCUIT ECM did not permit ICC operation.
LASER SUN BEAM Intense light such as sunlight entered ICC sensor light sensing part.
LASER TEMP Temperature around ICC sensor became low.
OP SW DOUBLE TOUCH ICC steering switches were pressed at the same time.
WHL SPD ELEC NOISE Wheel speed sensor signal caught electromagnetic noise.
VDC/TCS OFF SW VDC OFF switch was pressed.
WHEEL SPD UNMATCH Wheel speed became different from AT vehicle speed.
TIRE SLIP Wheel slipped.
PKB SW ON Parking brake is applied.
IGN LOW VOLT Power supply voltage became low.
SNOW MODE SW Snow mode switch was pressed.
NO RECORD —

AT-4Revision: 2005 July 2005 FX
In “N” Position, Vehicle Moves .............................
.196
Large Shock (“N” to “D” Position) ........................ .197
Vehicle Does Not Creep Backward in “R” Position .200
Vehicle Does Not Creep Forward in “D” Position . .203
Vehicle Cannot Be Started from D
1 ..................... .205
A/T Does Not Shift: D
1 → D2 ............................... .208
A/T Does Not Shift: D
2 → D3 ............................... .210
A/T Does Not Shift: D
3 → D4 ............................... .212
A/T Does Not Shift: D
4 → D5 ............................... .215
A/T Does Not Perform Lock-up ........................... .217
A/T Does Not Hold Lock-up Condition ................. .219
Lock-up Is Not Released ..................................... .221
Engine Speed Does Not Return to Idle ............... .221
Cannot Be Changed to Manual Mode ................. .223
A/T Does Not Shift: 5th Gear → 4th Gear ........... .223
A/T Does Not Shift: 4th Gear → 3rd Gear ........... .225
A/T Does Not Shift: 3rd Gear → 2nd Gear .......... .227
A/T Does Not Shift: 2nd Gear → 1st Gear ........... .229
Vehicle Does Not Decelerate by Engine Brake ... .231
SHIFT CONTROL SYSTEM ................................... .233
Control Device Removal and Installation ............. .233
Control Rod Removal and Installation ................. .234
Adjustment of A/T Position .................................. .235
Checking of A/T Position ..................................... .235
A/T SHIFT LOCK SYSTEM .................................... .236
Description ........................................................... .236
Shift Lock System Electrical Parts Location ........ .236
Wiring Diagram — AT — SHIFT .......................... .237
Diagnostic Procedure .......................................... .238
KEY INTERLOCK CABLE ..................................... .240
Components ........................................................ .240
Removal and Installation ..................................... .241
ON-VEHICLE SERVICE ......................................... .243
Control Valve with TCM and A/T Fluid Temperature
Sensor 2 .............................................................. .243
Parking Components (2WD Models Only) ........... .255
Rear Oil Seal ....................................................... .262
Revolution Sensor Components (2WD Models Only) ....................................................................
.263
AIR BREATHER HOSE .......................................... .268
Removal and Installation ...................................... .268
TRANSMISSION ASSEMBLY ................................ .270
Removal and Installation (2WD Models) .............. .270
Removal and Installation (AWD Models) ............. .273
OVERHAUL ............................................................ .278
Components ......................................................... .278
Oil Channel .......................................................... .286
Locations of Adjusting Shims, Needle Bearings,
Thrust Washers and Snap Rings ......................... .288
DISASSEMBLY ...................................................... .290
Disassembly ......................................................... .290
REPAIR FOR COMPONENT PARTS ..................... .308
Oil Pump .............................................................. .308
Front Sun Gear, 3rd One-way Clutch ................... .311
Front Carrier, Input Clutch, Rear Internal Gear .... .313
Mid Sun Gear, Rear Sun Gear, High and Low
Reverse Clutch Hub ............................................. .318
High and Low Reverse Clutch ............................. .323
Direct Clutch ........................................................ .326
ASSEMBLY ............................................................ .328
Assembly (1) ........................................................ .328
Adjustment ........................................................... .341
Assembly (2) ........................................................ .344
SERVICE DATA AND SPECIFICATIONS (SDS) ... .351
General Specifications ......................................... .351
Vehicle Speed at Which Gear Shifting Occurs ..... .351
Vehicle Speed at Which Lock-up Occurs/Releases .352
Stall Speed ........................................................... .352
Line Pressure ....................................................... .352
A/T Fluid Temperature Sensor ............................. .352
Turbine Revolution Sensor ................................... .353
Vehicle Speed Sensor A/T (Revolution Sensor) .. .353
Reverse Brake ..................................................... .353
Total End Play ...................................................... .353

A/T FLUID AT-13
D E
F
G H
I
J
K L
M A
B
AT
Revision: 2005 July 2005 FX
Checking A/T FluidACS002LC
1. Warm up engine.
2. Check for A/T fluid leakage.
3. Loosen the level gauge bolt.
4. Before driving, A/T fluid level can be checked at A/T fluid tem- peratures of 30 to 50 °C (86 to 122 °F) using “COLD” range on A/
T fluid level gauge as follows.
a. Park vehicle on level surface and set parking brake.
b. Start engine and move selector lever through each gear posi- tion. Leave selector lever in P position.
c. Check A/T fluid level with engine idling.
d. Remove A/T fluid level gauge and wipe clean with lint-free paper.
CAUTION:
When wiping away the A/T fluid level gauge, always use
lint-free paper, not a cloth one.
e. Re-insert A/T fluid level gauge into A/T fluid charging pipe as far as it will go. CAUTION:
To check A/T fluid level, insert the A/T fluid level gauge until the cap contacts the end of the A/T
fluid charging pipe, with the A/T fluid level gauge reversed from the normal attachment conditions.
f. Remove A/T fluid level gauge and note reading. If reading is at low side of range, add ATF to the A/T fluid charging pipe.
CAUTION:
Do not overfill.
5. Drive vehicle for approximately 5 minutes in urban areas.
6. Make the A/T fluid temperature approximately 65 °C (149 °F).
NOTE:
A/T fluid level will be greatly affected by temperature as shown in figure. Therefore, be certain to
perform operation while checking data with CONSULT-II.
a. Connect CONSULT-II to data link connector.
b. Select “MAIN SIGNALS” in “DATA MONITOR” mode for “A/T” with CONSULT-II.
c. Read out the value of “ATF TEMP 1”.
7. Recheck A/T fluid level at A/T fluid temperatures of approximately 65 °C (149 °F) using “HOT” range on A/
T fluid level gauge.
SCIA7120E
SLIA0016E

AT-20
A/T CONTROL SYSTEM
Revision: 2005 July 2005 FX
Shift MechanismACS002LE
The automatic transmission uses compact triple planetary gear systems to improve power transmission effi-
ciency, simplify construction and reduce weight.
It also employs an optimum shift control and super wide gear ratios. They improve starting performance and
acceleration during medium and high-speed operation.
CONSTRUCTION
FUNCTION OF CLUTCH AND BRAKE
1. Front brake 2. Input clutch 3. Direct clutch
4. High and low reverse clutch 5. Reverse brake 6. Forward brake
7. Low coast brake 8. 1st one-way clutch 9. Forward one-way clutch
10. 3rd one-way clutch 11. Front sun gear 12. Input shaft
13. Mid internal gear 14. Front internal gear 15. Rear carrier
16. Rear sun gear 17. Mid sun gear 18. Front carrier
19. Mid carrier 20. Rear internal gear 21. Output shaft
22. Parking gear 23. Parking pawl
PCIA0002J
Name of the Part Abbreviation Function
Front brake (1) FR/B Fastens the front sun gear (11).
Input clutch (2) I/C Connects the input shaft (12), the front internal gear (14) and the mid internal
gear (13).
Direct clutch (3) D/C Connects the rear carrier (15) and the rear sun gear (16).
High and low reverse clutch (4) HLR/C Connects the mid sun gear (17) and the rear sun gear (16).
Reverse brake (5) R/B Fastens the rear carrier (15).
Forward brake (6) Fwd/B Fastens the mid sun gear (17).
Low coast brake (7) LC/B Fastens the mid sun gear (17).
1st one-way clutch (8) 1st OWC Allows the rear sun gear (16) to turn freely forward relative to the mid sun gear
(17) but fastens it for reverse rotation.
Forward one-way clutch (9) Fwd OWC Allows the mid sun gear (17) to turn freely in the forward direction but fastens it
for reverse rotation.
3rd one-way clutch (10) 3rd OWC Allows the front sun gear (11) to turn freely in the forward direction but fastens
it for reverse rotation.

AT-22
A/T CONTROL SYSTEM
Revision: 2005 July 2005 FX
POWER TRANSMISSION
“N” Position
Since both the forward brake and the reverse brake are released, torque from the input shaft drive is not trans-
mitted to the output shaft.
“P” Position

The same as for the “N” position, both the forward brake and the reverse brake are released, so torque
from the input shaft drive is not transmitted to the output shaft.

The parking pawl linked with the selector lever meshes with the parking gear and fastens the output shaft
mechanically.
1. Front brake 2. Input clutch 3. Direct clutch
4. High and low reverse clutch 5. Reverse brake 6. Forward brake
7. Low coast brake 8. 1st one-way clutch 9. Forward one-way clutch
10. 3rd one-way clutch 11. Front sun gear 12. Input shaft
13. Mid internal gear 14. Front internal gear 15. Rear carrier
16. Rear sun gear 17. Mid sun gear 18. Front carrier
19. Mid carrier 20. Rear internal gear 21. Output shaft
22. Parking gear 23. Parking pawl
PCIA0003J

A/T CONTROL SYSTEM AT-23
D E
F
G H
I
J
K L
M A
B
AT
Revision: 2005 July 2005 FX
“D1 ” Position

The forward brake and the forward one-way clutch regulate reverse rotation of the mid sun gear.

The 1st one-way clutch regulates reverse rotation of the rear sun gear.

The 3rd one-way clutch regulates reverse rotation of the front sun gear.

During deceleration, the mid sun gear turns forward, so the forward one-way clutch idles and the engine
brake is not activated.
1. Front brake 2. Input clutch 3. Direct clutch
4. High and low reverse clutch 5. Reverse brake 6. Forward brake
7. Low coast brake 8. 1st one-way clutch 9. Forward one-way clutch
10. 3rd one-way clutch 11. Front sun gear 12. Input shaft
13. Mid internal gear 14. Front internal gear 15. Rear carrier
16. Rear sun gear 17. Mid sun gear 18. Front carrier
19. Mid carrier 20. Rear internal gear 21. Output shaft
22. Parking gear 23. Parking pawl
SCIA1512E