instrument panel INFINITI FX35 2005 User Guide

ATC-132
AIR MIX DOOR MOTOR
Revision: 2005 July 2005 FX
AIR MIX DOOR MOTOR PFP:27732
Removal and InstallationAJS0015M
REMOVAL
Driver Side
1. Set the temperature (driver side) at 18 °C (60 °F), and then disconnect the battery cable from the negative
terminal.
2. Remove instrument driver lower panel. Refer to IP-11, "
Removal and Installation" .
3. Remove mounting screws, and then remove air mix door motor.
4. Disconnect air mix door motor connector.
Passenger Side
1. Set the temperature (passenger side) at 18 °C (60 °F), and then disconnect the battery cable from the neg-
ative terminal.
2. Remove blower unit. Refer to ATC-121, "
BLOWER UNIT" .
3. Remove mounting screws, and then remove air mix door motor.
4. Disconnect air mix door motor connector.
INSTALLATION
Installation is basically the reverse order of removal.
RJIA0956E
RJIA0955E

ATC-134
DUCTS AND GRILLES
Revision: 2005 July 2005 FX
DUCTS AND GRILLESPFP:27860
Removal and InstallationAJS0015O
REMOVAL
Removal of Center Ventilator Grille
1. Remove cluster lid C. Refer to IP-11, "Removal and Installation" .
2. Remove mounting screws, and then remove center ventilator grille.
Removal of Side Ventilation
Remove side ventilation. Refer to IP-11, "Removal and Installation" .
Removal of Rear Ventilator Grille
1. Remove center pillar lower garnish. Refer to EI-36, "Removal and Installation" .
1. Defroster nozzle 2. Side defroster duct (left) 3. Side ventilator duct (left)
4. Instrument panel 5. Side ventilation (left) 6. Center ventilator grille (left)
7. Center ventilator grille (right) 8. Side ventilation (right) 9. Center ventilator duct (right)
10. Side ventilator duct (right) 11. Side defroster duct (right) 12. Center ventilator duct
13. Center ventilator duct (left)
RJIA2047E
RJIA2048E

DUCTS AND GRILLES ATC-135
C
D E
F
G H
I
K L
M A
B
AT C
Revision: 2005 July 2005 FX
2. Remove mounting clips, and then remove rear ventilator grille.
Removal of Defroster Nozzle, Ducts and Ventilator Ducts
1. Remove instrument panel assembly. Refer to IP-11, "Removal and Installation" .
2. Remove mounting screws, and then remove side defroster ducts, using power tools.
3. Remove mounting screws, and then remove defroster nozzle, using power tools.
4. Remove mounting screws, and then remove side ventilator duct (right and left).
5. Remove mounting screws, and then remove side ventilator ducts.
6. Remove mounting screws, and then remove center ventilator duct.
RJIA2050E
RJIA2051E

ATC-136
DUCTS AND GRILLES
Revision: 2005 July 2005 FX
Removal of Rear Ventilator Ducts
1. Remove center console. Refer to IP-11, "Removal and Installation" .
2. Slide rear ventilator duct 2 toward vehicle front, and then remove it.
3. Remove floor carpet. Refer to EI-39, "
Removal and Installation" .
4. Remove rear ventilator duct 3 mounting clips, and then remove rear ventilator duct 3.
5. Remove instrument panel assembly. Refer to IP-11, "
Removal and Installation" .
6. Remove rear ventilator duct 1 with center floor duct attached.
7. Remove rear ventilator duct 1 from center floor duct.
SJIA1227E
RJIA2053E
RJIA2054E

DUCTS AND GRILLES ATC-137
C
D E
F
G H
I
K L
M A
B
AT C
Revision: 2005 July 2005 FX
Removal of Foot Ducts
1. Remove heater & cooling unit. Refer to ATC-126, "HEATER & COOLING UNIT ASSEMBLY" .
2. Remove mounting screws, evaporator cover, and then remove foot duct (passenger side).
3. Remove foot duct (driver side).
Removal of Floor Ducts
1. Remove floor carpet. Refer to EI-39, "Removal and Installation" .
2. Remove mounting clips from side floor ducts.
3. Remove side floor ducts.
4. Remove instrument panel assembly. Refer to IP-11, "
Removal
and Installation" .
5. Remove center floor duct with rear ventilator duct 1 attached.
6. Remove center floor duct from rear ventilator duct 1.
INSTALLATION
Installation is basically the reverse order of removal.
RJIA0962E
RJIA2055E
RJIA2054E

AUDIO AV-47
C
D E
F
G H
I
J
L
M A
B
AV
Revision: 2005 July 2005 FX
Removal and Installation of Audio UnitAKS005TO
REMOVAL
1. Perform damper lock operation. Refer toAV- 4 6 , "Locking CD Auto-Changer Mechanism" .
2. Remove cluster lid C. Refer to IP-11, "
Removal and Installation" .
3. Remove screws (6) with power tool, and remove audio unit with display and unified meter and A/C amp. from instrument panel.
INSTALLATION
Installation is the reverse order of removal.
Disassembly and Assembly for Audio UnitAKS007YV
DISASSEMBLY
Remove audio unit screws (8) and display screws (4) and unified meter and A/C amp. screws (2) with power
tool and remove bracket.
CAUTION:

When carrying audio unit body, do not touch internal mechanism access from cassette tape slot.

Be careful not to allow foreign matter from cassette tape slot.
ASSEMBLY
Assembly is the reverse order of disassembly.
NOTE:
Use appropriate screws for each, as screws for audio unit and display unit are different from that for unified
meter and A/C amp.
SKIA5800E
1. Display 2. Bracket (LH) 3. Audio unit
4. Screw (For metal) 5. Screw (For plastic) 6. Bracket (RH)
7. Unified meter and A/C amp.
SKIA5799E

AUDIO AV-49
C
D E
F
G H
I
J
L
M A
B
AV
Revision: 2005 July 2005 FX
Removal and Installation for Rear Door SpeakerAKS005TS
REMOVAL
1. Remove rear door finisher. Refer to EI-34, "Removal and Instal-
lation" .
2. Remove screws (3) and remove rear door speaker.
INSTALLATION
Installation is the reverse order of removal.
Removal and Installation for Instrument SpeakerAKS005TU
REMOVAL
1. Remove grille from instrument panel.
2. Remove screws (4) and disconnect connector.
3. Remove instrument speaker.
INSTALLATION
Installation is the reverse order of removal.
Removal and Installation for TweeterAKS005TV
REMOVAL
1. Remove rear pillar upper garnish assembly. Refer to EI-43,
"Removal and Installation" .
2. Remove screws (4), and disconnect connector.
3. Remove tweeter.
INSTALLATION
Installation is the reverse order of removal.
SKIA5804E
SKIA5805E
SKIA5806E

AV-56
AUDIO ANTENNA
Revision: 2005 July 2005 FX
Removal and Installation of Roof AntennaAKS005TZ
REMOVAL
1. Remove head lining. Refer to EI-41, "HEADLINING" .
2. Remove nut and remove rod and antenna base.
3. Remove instrument panel. Refer to IP-10, "
INSTRUMENT
PANEL ASSEMBLY" .
4. Disassembly antenna feeder (upper) and antenna feeder (lower).
5. Disengaged the clips (7) to separate antenna feeder (upper) from vehicle.
6. Pull off antenna feeder (lower) from audio unit.
7. Disengaged the clips (5) to separate antenna feeder (lower) from vehicle.
INSTALLATION
Installation is the reverse order of removal.
PKIA2463E
SKIA5821E

INTEGRATED DISPLAY SYSTEM AV-57
C
D E
F
G H
I
J
L
M A
B
AV
Revision: 2005 July 2005 FX
INTEGRATED DISPLAY SYSTEMPFP:28090
System DescriptionAKS005U0
A/C AND AV SWITCH SYSTEM
Refer to Owner′s Manual for A/C and AV switch operating instructions.
Using the A/C and AV switch at the center of the instrument panel, the controls of the following systems are
centralized:

Integrated display system (Drive computer, setting screen, etc.)

Auto A/C system

Audio system
PRECAUTION OF LCD MONITOR

In order to use LED for backlight of a display, by interior temperature, brightness may change. In low tem-
perature, the refreshing rate of the picture also becomes low because of the low response of the LCD
monitor. When the interior becomes warm, however, the LCD recovers the normal display.

Backlight sometimes flickers or darkens according to the wearing out of LCD and the number of times
switched ON and OFF. In this case, display unit should be replaced. (Exchange only of backlight is impos-
sible.)
POWER SUPPLY AND GROUND
Power is supplied at all times

through 15A fuse (No. 32, located in fuse and fusible link box)

to audio unit terminal 6

to display unit terminal 1 and

to A/C and AV switch terminal 1.
When ignition switch is in ACC or ON position, power is supplied

through 10A fuse [No. 6, located in fuse block (J/B)]

to unified meter and A/C amp. terminal 35

to audio unit terminal 10

to display unit terminal 2 and

to A/C and AV switch terminal 2.
When ignition switch is in ON or START position, power is supplied

through 10A fuse [No. 12, located in fuse block (J/B)]

to unified meter and A/C amp. terminal 22 and

to display unit terminal 3.
Ground is supplied

to unified meter and A/C amp. terminals 29, 30

to display unit terminals 6 and 15 and

to A/C and AV switch terminal 5

through body grounds M35, M45 and M85.
Ground is supplied through the case of the audio unit.

INTEGRATED DISPLAY SYSTEM AV-61
C
D E
F
G H
I
J
L
M A
B
AV
Revision: 2005 July 2005 FX
D/N SCREEN

Turning on “DAY/NIGHT” switch, DAY MODE or NIGHT MODE
is indicated for present mode.

If press “DAY/NIGHT” again when display adjustment lumi-
nance, change DAY-NIGHT (NIGHT-DAY) mode (screen of
adjustment luminance).
As follows:

Press “PREV” or not operate for 10sec. when displayed screen
of adjustment luminance, back to default screen (same mode).

Can adjust luminance by “DISP” switch. Light can be adjusted by pressing “+” (bright) or “–” (dark).

Adjustment range is a 12 stage (MIN to MAX) and default set value is 10 (DAY) and 4 (NIGHT).
WARNING INDICATIONS
When BCM receives warning signal from some control units or sensors, then combination meter warning lamp
is illuminated.
Then BCM sends warning signal to display unit warning indications on the screen.
AV COMMUNICATION LINE
Display unit is controlled by the following unit with AV communication line.

A/C and AV switch
CAN Communication System DescriptionAKS007Z5
CAN (Controller Area Network) is a serial communication line for real time application. It is an on-vehicle mul-
tiplex communication line with high data communication speed and excellent error detection ability. Many elec-
tronic control units are equipped onto a vehicle, and each control unit shares information and links with other
control units during operation (not independent). In CAN communication, control units are connected with 2
communication lines (CAN H line, CAN L line) allowing a high rate of information transmission with less wiring.
Each control unit transmits/receives data but selectively reads required data only.
CAN Communication UnitAKS007YZ
Refer to LAN-30, "CAN Communication Unit" .
Component Parts and Harness Connector Location AKS005U2
NOW Change display
DAY DAY →NIGHT →DAY →·····
NIGHT NIGHT →DAY →NIGHT →·····
SKIA5920E
Warning indicators Warning lamps in
instrument panel Warning detection and cancel conditions Cases of malfunction
DOOR OPEN Door Detection
condition Vehicle is running [approx. 3.5 km/h (2 MPH) or
faster] and door ajar of any of the doors is detected. Door is open.
Cancel
condition Vehicle is stopped and all the doors close.
SKIA4970E