Lighting system INFINITI FX35 2005 Workshop Manual
[x] Cancel search | Manufacturer: INFINITI, Model Year: 2005, Model line: FX35, Model: INFINITI FX35 2005Pages: 4731, PDF Size: 60.13 MB
Page 2237 of 4731
![INFINITI FX35 2005 Workshop Manual EC-844
[VK45DE]
TROUBLE DIAGNOSIS - SPECIFICATION VALUE
Revision: 2005 July 2005 FX
TROUBLE DIAGNOSIS - SPECIFICATION VALUEPFP:00031
DescriptionABS00E4K
The specification (SP) value indicates the tole](/img/42/57020/w960_57020-2236.png "INFINITI FX35 2005 Workshop Manual EC-844
[VK45DE]
TROUBLE DIAGNOSIS - SPECIFICATION VALUE
Revision: 2005 July 2005 FX
TROUBLE DIAGNOSIS - SPECIFICATION VALUEPFP:00031
DescriptionABS00E4K
The specification (SP) value indicates the tole")
EC-844
[VK45DE]
TROUBLE DIAGNOSIS - SPECIFICATION VALUE
Revision: 2005 July 2005 FX
TROUBLE DIAGNOSIS - SPECIFICATION VALUEPFP:00031
DescriptionABS00E4K
The specification (SP) value indicates the tolerance of the value that is displayed in “DATA MONITOR (SPEC)”
mode of CONSULT-II during normal operation of the Engine Control System. When the value in “DATA MONI-
TOR (SPEC)” mode is within the SP value, the Engine Control System is confirmed OK. When the value in
“DATA MONITOR (SPEC)” mode is NOT within the SP value, the Engine Control System may have one or
more malfunctions.
The SP value is used to detect malfunctions that may affect the Engine Control System, but will not light the
MIL.
The SP value will be displayed for the following three items:
B/FUEL SCHDL (The fuel injection pulse width programmed into ECM prior to any learned on board cor-
rection)
A/F ALPHA-B1/B2 (The mean value of air-fuel ratio feedback correction factor per cycle)
MAS A/F SE-B1 (The signal voltage of the mass air flow sensor)
Testing ConditionABS00E4L
Vehicle driven distance: More than 5,000 km (3,017 miles)
Barometric pressure: 98.3 - 104.3 kPa (1.003 - 1.064 kg/cm2 , 14.25 - 15.12 psi)
Atmospheric temperature: 20 - 30 °C (68 - 86 °F)
Engine coolant temperature: 75 - 95 °C (167 - 203 °F)
Transmission: Warmed-up*1
Electrical load: Not applied*2
Engine speed: Idle
*1: After the engine is warmed up to normal operating temperature, drive vehicle until “ATF TEMP 1” (A/T fluid
temperature sensor signal) indicates more than 60 °C (140 °F).
*2: Rear window defogger switch, air conditioner switch, lighting switch are OFF. Steering wheel is straight
ahead.
Inspection ProcedureABS00E4M
NOTE:
Perform “DATA MONITOR (SPEC)” mode in maximum scale display.
1. Perform EC-769, "
Basic Inspection" .
2. Confirm that the testing conditions indicated above are met.
3. Select “B/FUEL SCHDL”, “A/F ALPHA-B1”, “A/F ALPHA-B2” and “MAS A/F SE-B1” in “DATA MONITOR (SPEC)” mode with
CONSULT-II.
4. Make sure that monitor items are within the SP value.
5. If NG, go to EC-845, "
Diagnostic Procedure" .
SEF601Z
Page 2762 of 4731
![INFINITI FX35 2005 Workshop Manual ELECTRICAL LOAD SIGNAL EC-1369
[VK45DE]
C
D E
F
G H
I
J
K L
M A
EC
Revision: 2005 July 2005 FX
ELECTRICAL LOAD SIGNALPFP:25350
DescriptionABS007XB
The electrical load signal (Headlamp swi](/img/42/57020/w960_57020-2761.png "INFINITI FX35 2005 Workshop Manual ELECTRICAL LOAD SIGNAL EC-1369
[VK45DE]
C
D E
F
G H
I
J
K L
M A
EC
Revision: 2005 July 2005 FX
ELECTRICAL LOAD SIGNALPFP:25350
DescriptionABS007XB
The electrical load signal (Headlamp swi")
ELECTRICAL LOAD SIGNAL EC-1369
[VK45DE]
C
D E
F
G H
I
J
K L
M A
EC
Revision: 2005 July 2005 FX
ELECTRICAL LOAD SIGNALPFP:25350
DescriptionABS007XB
The electrical load signal (Headlamp switch signal, rear window defogger switch signal, etc.) is transferred
through the CAN communication line from BCM to ECM via IPDM E/R.
CONSULT-II Reference Value in Data Monitor ModeABS007XC
Specification data are reference values.
Diagnostic ProcedureABS007XD
1. CHECK LOAD SIGNAL CIRCUIT OVERALL FUNCTION-I
1. Turn ignition switch ON.
2. Connect CONSULT-II and select “DATA MONITOR” mode.
3. Select “LOAD SIGNAL” and check indication under the following conditions.
OK or NG
OK >> GO TO 2.
NG >> GO TO 3.
2. CHECK LOAD SIGNAL CIRCUIT OVERALL FUNCTION-II
Check “LOAD SIGNAL” indication under the following conditions.
OK or NG
OK >> INSPECTION END
NG >> GO TO 4.
3. CHECK REAR WINDOW DEFOGGER SYSTEM
Refer to GW-86, "
REAR WINDOW DEFOGGER" .
>> INSPECTION END
4. CHECK HEADLAMP SYSTEM
Refer to LT- 7 , "
HEADLAMP - XENON TYPE -" .
>> INSPECTION END
MONITOR ITEM CONDITION SPECIFICATION
LOAD SIGNAL
Ignition switch: ON Rear window defogger switch: ON
and/or
Lighting switch: 2ND position ON
Rear window defogger switch and light-
ing switch: OFF OFF
Condition Indication
Rear window defogger switch: ON ON
Rear window defogger switch: OFF OFF
PBIB0103E
Condition Indication
Lighting switch: ON at 2nd position ON
Lighting switch: OFF OFF
PBIB0103E
Page 3224 of 4731
PRECAUTIONS GI-3
C
D E
F
G H
I
J
K L
M B
GI
Revision: 2005 July 2005 FX
PRECAUTIONSPFP:00001
DescriptionAAS000EV
Observe the following precautions to ensure safe and proper servicing. These precautions are not
described in each individual section.
Precautions for Supplemental Restraint System (SRS) “AIR BAG” and “SEAT
BELT PRE-TENSIONER”
AAS000EW
The Supplemental Restraint System such as “AIR BAG” and “SEAT BELT PRE-TENSIONER”, used along
with a front seat belt, helps to reduce the risk or severity of injury to the driver and front passenger for certain
types of collision. This system includes seat belt switch inputs and dual stage front air bag modules. The SRS
system uses the seat belt switches to determine the front air bag deployment, and may only deploy one front
air bag, depending on the severity of a collision and whether the front occupants are belted or unbelted.
Information necessary to service the system safely is included in the SRS and SB section of this Service Man-
ual.
WARNING:
To avoid rendering the SRS inoperative, which could increase the risk of personal injury or death
in the event of a collision which would result in air bag inflation, all maintenance must be per-
formed by an authorized NISSAN/INFINITI dealer.
Improper maintenance, including incorrect removal and installation of the SRS, can lead to per-
sonal injury caused by unintentional activation of the system. For removal of Spiral Cable and Air
Bag Module, see the SRS section.
Do not use electrical test equipment on any circuit related to the SRS unless instructed to in this
Service Manual. SRS wiring harnesses can be identified by yellow and/or orange harnesses or
harness connectors.
Precautions for NVIS/IVIS (NISSAN/INFINITI VEHICLE IMMOBILIZER SYSTEM -
NATS) (If Equipped)
AAS000EX
NVIS/IVIS (NATS) will immobilize the engine if someone tries to start it without the registered key of NVIS/IVIS
(NATS).
Both of the originally supplied ignition key IDs have been NVIS/IVIS (NATS) registered.
The security indicator is located on the instrument panel. The indicator blinks when the immobilizer system is
functioning.
Therefore, NVIS/IVIS (NATS) warns outsiders that the vehicle is equipped with the anti-theft system.
When NVIS/IVIS (NATS) detects trouble, the security indicator lamp lights up while ignition switch is in
"ON" position.
This lighting up indicates that the anti-theft is not functioning, so prompt service is required.
When servicing NVIS/IVIS (NATS) (trouble diagnoses, system initialization and additional registration of
other NVIS/IVIS (NATS) ignition key IDs), CONSULT-II hardware and CONSULT-II NVIS/IVIS (NATS)
software is necessary.
Regarding the procedures of NVIS/IVIS (NATS) initialization and NVIS/IVIS (NATS) ignition key ID regis-
tration, refer to CONSULT-II operation manual, NVIS/IVIS (NATS).
Therefore, CONSULT-II NVIS/IVIS (NATS) software (program card and operation manual) must be kept
strictly confidential to maintain the integrity of the anti-theft function.
When servicing NVIS/IVIS (NATS) (trouble diagnoses, system initialization and additional registration of
other NVIS/IVIS (NATS) ignition key IDs), it may be necessary to re-register original key identification.
Therefore, be sure to receive all keys from vehicle owner. A maximum of four or five key IDs can be regis-
tered into NVIS/IVIS (NATS).
When failing to start the engine first time using the key of NVIS/IVIS (NATS), start as follows.
1. Leave the ignition key in "ON" position for approximately 5 seconds.
2. Turn ignition key to "OFF" or "LOCK" position and wait approximately 5 seconds.
3. Repeat step 1 and 2 again.
4. Restart the engine while keeping the key separate from any others on key-chain.
Page 3412 of 4731
INSTRUMENT PANEL ASSEMBLY IP-11
C
D E
F
G H
J
K L
M A
B
IP
Revision: 2005 July 2005 FX
Removal and InstallationAIS003CJ
WORK STEP
When removing instrument panel and pad, combination meter, display unit and audio unit, center console take
steps in the order shown by the numbers below.
CAUTION:
Disconnect both battery cables in advance.
Disconnect air bag system line in advance.
Never temper with air bag lid or force air bag lid to open, as this may adversely affect air bag per-
formance.
Be careful not to scratch pad and other parts.
1. Front defroster grille (RH) 2. Instrument panel and pad 3. Front defroster grille (LH)
4. Screw 5. Bolt 6. Combination meter assembly
7. Steering lock escutcheon 8. Side ventilation (LH) 9. Display unit and audio unit
10. Wiper and washer switch 11. Clip 12. Rubber
13. Lighting and turn signal switch 14. Combination meter bracket 15. Cluster lid C
16. Steering column upper cover 17. Steering column lower cover 18. Steering column front lower cover
19. Instrument side panel (LH) 20. Instrument clock finisher 21. A/T console finisher
22. Instrument driver lower panel 23. Console finisher (LH) 24. Center console
25. Console finisher (RH) 26. Instrument side panel (RH) 27. Instrument lower cover
28. Instrument passenger lower panel 29. Side ventilation (RH) 30. Front passenger air bag module mounting nut
Parts Reference
page Instrument
panel and pad Combination
meter Display unit and
audio unit Center console
(A) Front kicking plate (RH/LH) EI-38
[ 1 ] [ 1 ]
(B) Dash side finisher (RH/LH) EI-37
[ 2 ] [ 2 ]
(C) Front pillar garnish (RH/LH) EI-38
[ 3 ]
(D) A/T select lever knob AT- 2 3 3
[ 4 ] [ 1 ]
(E) Instrument clock finisher IP-12
[ 5 ] [ 2 ]
(F) A/T console finisher IP-12
[ 6 ] [ 3 ]
(G) Console finisher (RH/LH) IP-12
[ 7 ] [ 4 ]
(H) Center console IP-12
[ 8 ] [ 5 ]
(I) Instrument lower cover IP-13
[ 9 ]
(J) Instrument passenger lower panel IP-13
[10]
(K) Instrument driver lower panel IP-13
[11] [ 3 ]
(L) Steering column front lower cover IP-13
[12] [ 4 ]
(M) Steering column lower cover IP-13
[13] [ 5 ]
(N) Steering column upper cover IP-14
[14] [ 6 ]
(O) Wiper and washer switch IP-14
[15] [ 7 ]
(P) Lighting and turn signal switch IP-14
[16] [ 8 ]
(Q) Steering lock escutcheon IP-14
[17] [ 9 ]
(R) Combination meter assembly IP-14
[18] [10]
(S) Instrument side panel (RH/LH) IP-14
[19]
(T) Cluster lid C IP-15
[20] [ 1 ]
(U) Display unit and audio unit IP-15
[21] [ 2 ]
(V) Front defroster grille (RH/LH) IP-15
[22]
(W) Combination meter bracket IP-15
[23]
(X) Side ventilation (RH/LH) IP-16
[24]
(Y) Instrument panel and pad IP-16
[25]
Page 3890 of 4731
LT-1
LIGHTING SYSTEM
K ELECTRICAL
CONTENTS
C
D E
F
G H
I
J
L
M
SECTION LT
A
B
LT
Revision: 2005 July 2005 FX
LIGHTING SYSTEM
PRECAUTIONS .......................................................... 5
Precautions for Supplemental Restraint System
(SRS) “AIR BAG” and “SEAT BELT PRE-TEN-
SIONER” ............................................................. ..... 5
General Precautions for Service Operations ....... ..... 6
HEADLAMP - XENON TYPE - .............................. ..... 7
Component Parts and Harness Connector Location ..... 7
System Description ............................................. ..... 7
OUTLINE .......................................................... ..... 7
HEADLAMP OPERATION ............................... ..... 8
COMBINATION SWITCH READING FUNCTION ..... 9
EXTERIOR LAMP BATTERY SAVER CONTROL ..... 9
AUTO LIGHT OPERATION (IF EQUIPPED) .... ..... 9
VEHICLE SECURITY SYSTEM ....................... ..... 9
XENON HEADLAMP ........................................ ..... 9
CAN Communication System Description ........... ..... 9
CAN Communication Unit ................................... ..... 9
Schematic ........................................................... ... 10
Wiring Diagram — H/LAMP — ............................ .... 11
Terminals and Reference Values for BCM .......... ... 15
Terminals and Reference Values for IPDM E/R .. ... 15
How to Proceed With Trouble Diagnosis ............. ... 16
Preliminary Check ............................................... ... 16
CHECK POWER SUPPLY AND GROUND CIR-
CUIT ................................................................. ... 16
CONSULT-II Functions (BCM) ............................ ... 18
CONSULT-II BASIC OPERATION .................... ... 18
WORK SUPPORT ............................................ ... 19
DATA MONITOR .............................................. ... 19
ACTIVE TEST .................................................. ... 20
CONSULT-II Functions (IPDM E/R) .................... ... 20
CONSULT-II BASIC OPERATION .................... ... 21
DATA MONITOR .............................................. ... 22
ACTIVE TEST .................................................. ... 23
Headlamp Does Not Change To High Beam (Both
Sides) .................................................................. ... 23
Headlamp Does Not Change To High Beam (One
Side) .................................................................... ... 25
High Beam Indicator Lamp Does Not Illuminate . ... 26
Headlamp Low Beam Does Not Illuminate (Both Sides) ..................................................................
... 26
Headlamp Low Beam Does Not Illuminate (One
Side) .................................................................... ... 29
Headlamp RH Low Beam and High Beam Does Not
Illuminate ............................................................. ... 30
Headlamp LH Low Beam and High Beam Does Not
Illuminate ............................................................. ... 31
Headlamps Do Not Turn OFF .............................. ... 32
General Information for Xenon Headlamp Trouble
Diagnosis ............................................................. ... 34
Caution: ............................................................... ... 34
Xenon Headlamp Trouble Diagnosis ................... ... 34
Aiming Adjustment ............................................... ... 35
PREPARATION BEFORE ADJUSTING ........... ... 35
LOW BEAM AND HIGH BEAM ........................ ... 35
ADJUSTMENT USING AN ADJUSTMENT
SCREEN (LIGHT/DARK BORDERLINE) ......... ... 36
Bulb Replacement ............................................... ... 36
HEADLAMP HIGH/LOW BEAM ....................... ... 36
DAYTIME/PARKING LAMP .............................. ... 37
FRONT TURN SIGNAL LAMP ......................... ... 37
FRONT SIDE MARKER LAMP ........................ ... 37
Removal and Installation ..................................... ... 37
REMOVAL ........................................................ ... 37
INSTALLATION ................................................ ... 38
Disassembly and Assembly ................................. ... 38
DISASSEMBLY ................................................ ... 38
ASSEMBLY ...................................................... ... 38
DAYTIME LIGHT SYSTEM .................................... ... 39
Component Parts and Harness Connector Location ... 39
System Description .............................................. ... 39
OUTLINE .......................................................... ... 39
DAYTIME LIGHT OPERATION ........................ ... 40
COMBINATION SWITCH READING FUNCTION ... 40
AUTO LIGHT OPERATION .............................. ... 40
CAN Communication System Description ........... ... 40
CAN Communication Unit .................................... ... 40
Schematic ............................................................ ... 41
Wiring Diagram — DTRL — ................................ ... 42
Terminals and Reference Values for BCM ........... ... 46
Page 3891 of 4731
LT-2Revision: 2005 July 2005 FX
How to Proceed With Trouble Diagnosis .............
... 46
Preliminary Check ............................................... ... 47
CHECK POWER SUPPLY AND GROUND CIR-
CUIT ................................................................. ... 47
INSPECTION PARKING BRAKE SWITCH CIR-
CUIT ................................................................. ... 48
CONSULT-II Functions (BCM) ............................. ... 49
CONSULT-II BASIC OPERATION .................... ... 49
DATA MONITOR ............................................... ... 50
ACTIVE TEST .................................................. ... 51
Daytime Light Control Does Not Operate Properly ... 52
Aiming Adjustment ............................................... ... 54
Bulb Replacement ............................................... ... 54
Removal and Installation ..................................... ... 54
Disassembly and Assembly ................................. ... 54
AUTO LIGHT SYSTEM .......................................... ... 55
Component Parts and Harness Connector Location ... 55
System Description .............................................. ... 55
OUTLINE .......................................................... ... 55
COMBINATION SWITCH READING FUNCTION ... 56
EXTERIOR LAMP BATTERY SAVER CONTROL ... 56
DELAY TIMER FUNCTION .............................. ... 56
CAN Communication System Description ........... ... 56
CAN Communication Unit .................................... ... 56
Major Components and Functions ....................... ... 56
Schematic ............................................................ ... 57
Wiring Diagram — AUTO/L — ............................. ... 58
Terminals and Reference Values for BCM ........... ... 61
Terminals and Reference Values for IPDM E/R ... ... 62
How to Proceed With Trouble Diagnosis ............. ... 62
Preliminary Check ............................................... ... 63
SETTING CHANGE FUNCTIONS .................... ... 63
CHECK POWER SUPPLY AND GROUND CIR-
CUIT ................................................................. ... 63
CONSULT-II Functions (BCM) ............................. ... 65
CONSULT-II BASIC OPERATION .................... ... 65
WORK SUPPORT ............................................ ... 66
DATA MONITOR ............................................... ... 66
ACTIVE TEST .................................................. ... 67
CONSULT-II Functions (IPDM E/R) ..................... ... 68
CONSULT-II BASIC OPERATION .................... ... 68
DATA MONITOR ............................................... ... 69
ACTIVE TEST .................................................. ... 69
Symptom Chart .................................................... ... 70
Lighting Switch Inspection ................................... ... 70
Optical sensor System Inspection ....................... ... 71
Removal and Installation of Optical Sensor ......... ... 73
REMOVAL ........................................................ ... 73
INSTALLATION ................................................. ... 73
HEADLAMP AIMING CONTROL ........................... ... 74
Schematic ............................................................ ... 74
Wiring Diagram — H/AIM — ................................ ... 75
Removal and Installation ..................................... ... 78
REMOVAL ........................................................ ... 78
INSTALLATION ................................................. ... 78
Switch Circuit Inspection ..................................... ... 78
FRONT FOG LAMP ............................................... ... 79
Component Parts and Harness Connector Location ... 79 System Description ..............................................
... 79
OUTLINE .......................................................... ... 79
FRONT FOG LAMP OPERATION .................... ... 80
COMBINATION SWITCH READING FUNCTION ... 80
EXTERIOR LAMP BATTERY SAVER CONTROL ... 80
CAN Communication System Description ........... ... 80
CAN Communication Unit .................................... ... 80
Wiring Diagram — F/FOG — ............................... ... 81
Terminals and Reference Values for BCM ........... ... 83
Terminals and Reference Values for IPDM E/R ... ... 83
How to Proceed With Trouble Diagnosis ............. ... 84
Preliminary Check ................................................ ... 84
CHECK POWER SUPPLY AND GROUND CIR-
CUIT .................................................................. ... 84
CONSULT-II Functions (BCM) ............................. ... 85
CONSULT-II Functions (IPDM E/R) ..................... ... 85
Front Fog Lamp Does Not Illuminate (Both Sides) ... 86
Front Fog Lamp Does Not Illuminate (One Side) . ... 88
Aiming Adjustment ............................................... ... 89
Bulb Replacement ................................................ ... 90
Removal and Installation ...................................... ... 90
REMOVAL ......................................................... ... 90
INSTALLATION ................................................. ... 90
TURN SIGNAL AND HAZARD WARNING LAMPS ... 91
Component Parts and Harness Connector Location ... 91
System Description .............................................. ... 91
TURN SIGNAL OPERATION ............................ ... 91
HAZARD LAMP OPERATION .......................... ... 92
REMOTE CONTROL ENTRY SYSTEM OPER-
ATION ............................................................... ... 93
COMBINATION SWITCH READING FUNCTION ... 94
CAN Communication System Description ........... ... 94
CAN Communication Unit .................................... ... 94
Schematic ............................................................ ... 95
Wiring Diagram — TURN — ................................ ... 96
Terminals and Reference Values for BCM ........... ... 99
How to Proceed With Trouble Diagnosis ............. .100
Preliminary Check ................................................ .100
CHECK POWER SUPPLY AND GROUND CIR-
CUIT .................................................................. .100
CONSULT-II Functions (BCM) ............................. .102
CONSULT-II BASIC OPERATION .................... .102
DATA MONITOR ............................................... .103
ACTIVE TEST ................................................... .103
Turn Signal Lamp Does Not Operate ................... .103
Rear Turn Signal Lamp Does Not Operate .......... .105
Hazard Warning Lamp Does Not Operate But Turn
Signal Lamp Operate ........................................... .107
Turn Signal Indicator Lamp Does Not Operate .... .108
Bulb Replacement (Front Turn Signal Lamp) ....... .108
Bulb Replacement (Rear Turn Signal Lamp) ....... .108
Removal and Installation of Front Turn Signal Lamp .108
Removal and Installation of Rear Turn Signal Lamp .108
Removal and Installation of Rear Combination
Lamp Control Unit ................................................ .109
REMOVAL ......................................................... .109
INSTALLATION ................................................. .109
Page 3892 of 4731
LT-3
C
D E
F
G H
I
J
L
M A
B
LT
Revision: 2005 July 2005 FX
LIGHTING AND TURN SIGNAL SWITCH .............
..110
Removal and Installation ..................................... .. 110
REMOVAL ........................................................ .. 110
INSTALLATION ................................................ .. 110
HAZARD SWITCH ................................................. .. 111
Removal and Installation ..................................... . . 111
REMOVAL ........................................................ . . 111
INSTALLATION ................................................ . . 111
COMBINATION SWITCH ....................................... ..112
Wiring Diagram — COMBSW — ......................... .. 112
Combination Switch Reading Function ............... .. 113
CONSULT-II Functions (BCM) ............................ .. 113
CONSULT-II BASIC OPERATION .................... .. 113
DATA MONITOR .............................................. .. 114
Combination Switch Inspection ........................... .. 115
Removal and Installation ..................................... .. 117
STOP LAMP .......................................................... ..118
Component Parts and Harness Connector Location .. 118
System Description ............................................. .. 118
Schematic ........................................................... .. 119
Wiring Diagram — STOP/L — ............................. . 120
Stop Lamp Does Not Operate ............................. . 123
High-Mounted Stop Lamp ................................... . 125
BULB REPLACEMENT, REMOVAL AND
INSTALLATION ................................................ . 125
Stop Lamp ........................................................... . 125
BULB REPLACEMENT .................................... . 125
REMOVAL AND INSTALLATION ..................... . 125
Rear Combination Lamp Control Unit ................. . 125
REMOVAL AND INSTALLATION ..................... . 125
STEP LAMP ........................................................... . 126
Front Door Step Lamp ......................................... . 126
BULB REPLACEMENT, REMOVAL AND
INSTALLATION ................................................ . 126
Rear Door Step Lamp ......................................... . 126
BULB REPLACEMENT, REMOVAL AND
INSTALLATION ................................................ . 126
BACK-UP LAMP ................................................... . 127
Wiring Diagram — BACK/L — ............................ . 127
Bulb Replacement ............................................... . 128
Removal and Installation ..................................... . 128
PARKING, LICENSE PLATE AND TAIL LAMPS .. . 129
Component Parts and Harness Connector Location . 129
System Description ............................................. . 129
OUT LINE ......................................................... . 129
OPERATION BY LIGHTING SWITCH ............. . 130
COMBINATION SWITCH READING FUNCTION . 131
EXTERIOR LAMP BATTERY SAVER CONTROL . 131
CAN Communication System Description ........... . 131
CAN Communication Unit ................................... . 131
Schematic ........................................................... . 132
Wiring Diagram — TAIL/L — ............................... . 133
Terminals and Reference Values for BCM .......... . 138
Terminals and Reference Values for IPDM E/R .. . 138
How to Proceed With Trouble Diagnosis ............. . 139
Preliminary Check ............................................... . 139
CHECK POWER SUPPLY AND GROUND CIR-
CUIT ................................................................. . 139
CONSULT-II Functions (BCM) ............................ . 140 CONSULT-II Functions (IPDM E/R) .....................
.140
Parking, License Plate and Side Marker Lamps Do
Not Illuminate ....................................................... .140
Tail Lamp Does Not Operate ............................... .146
Parking, License Plate, Side Maker and Tail Lamps
Do Not Turn OFF (After Approx. 10 Minutes) ...... .147
License Plate Lamp ............................................. .147
BULB REPLACEMENT, REMOVAL AND
INSTALLATION ................................................ .147
Front Parking Lamp ............................................. .148
BULB REPLACEMENT .................................... .148
REMOVAL AND INSTALLATION ..................... .148
Tail Lamp ............................................................. .148
BULB REPLACEMENT .................................... .148
REMOVAL AND INSTALLATION ..................... .148
Front Side Marker Lamp ...................................... .148
BULB REPLACEMENT .................................... .148
REMOVAL AND INSTALLATION ..................... .148
Rear Side Marker Lamp ...................................... .148
BULB REPLACEMENT .................................... .148
REMOVAL AND INSTALLATION ..................... .148
Rear Combination Lamp Control Unit .................. .148
REMOVAL AND INSTALLATION ..................... .148
REAR COMBINATION LAMP ................................ .149
Bulb Replacement ............................................... .149
REAR FENDER SIDE (REAR SIDE MARKER
LAMP BULB) .................................................... .149
BACK DOOR SIDE (BACK-UP LAMP) ............ .149
Removal and Installation ..................................... .149
REMOVAL ........................................................ .149
INSTALLATION ................................................ .150
VANITY MIRROR LAMP ........................................ .151
Bulb Replacement ............................................... .151
MAP LAMP ............................................................ .152
Bulb Replacement ............................................... .152
Removal and Installation ..................................... .152
REMOVAL ........................................................ .152
INSTALLATION ................................................ .152
PERSONAL LAMP ................................................ .153
Bulb Replacement ............................................... .153
Removal and Installation ..................................... .153
REMOVAL ........................................................ .153
INSTALLATION ................................................ .153
LUGGAGE ROOM LAMP ...................................... .154
Bulb Replacement ............................................... .154
Removal and Installation ..................................... .154
REMOVAL ........................................................ .154
INSTALLATION ................................................ .154
IGNITION KEY HOLE ILLUMINATION .................. .155
Bulb Replacement, Removal and Installation ...... .155
GLOVE BOX LAMP ............................................... .156
Bulb Replacement, Removal and Installation ...... .156
ASHTRAY ILLUMINATION .................................... .157
Bulb Replacement and Removal and Installation . 157
CIGARETTE LIGHTER ILLUMINATION ................ .158
Bulb Replacement and Removal and Installation . 158
INTERIOR ROOM LAMP ....................................... .159
Component Parts and Harness Connector Location .159
System Description .............................................. .159
Page 3893 of 4731
LT-4Revision: 2005 July 2005 FX
POWER SUPPLY AND GROUND ....................
.160
SWITCH OPERATION ..................................... .161
ROOM LAMP TIMER OPERATION .................. .162
INTERIOR LAMP BATTERY SAVER CONTROL .163
Schematic ............................................................ .165
Wiring Diagram — ROOM/L — ............................ .167
Terminals and Reference Values for BCM ........... .175
How to Proceed With Trouble Diagnosis ............. .176
Preliminary Check ............................................... .176
CHECK FOR POWER SUPPLY AND GROUND
CIRCUIT ........................................................... .176
CONSULT-II Functions (BCM) ............................. .177
CONSULT-II BASIC OPERATION .................... .177
WORK SUPPORT ............................................ .178
DATA MONITOR ............................................... .178
ACTIVE TEST .................................................. .179
Interior Room Lamp Control Does Not Operate .. .180
Map Lamp Control Does Not Operate ................. .181
Personal Lamp Control Does Not Operate .......... .183
Ignition Key Hole Illumination Control Does Not
Operate ................................................................ .184
All Step Lamps Do Not Operate ........................... .186
All Interior Room Lamps Do Not Operate ............ .187
Bulb Replacement ............................................... .187 INTERIOR ROOM LAMP ..................................
.187
MAP LAMP ....................................................... .187
PERSONAL LAMP ............................................ .187
Removal and Installation ...................................... .188
INTERIOR ROOM LAMP .................................. .188
MAP LAMP ....................................................... .188
PERSONAL LAMP ............................................ .188
ILLUMINATION ....................................................... .189
System Description .............................................. .189
ILLUMINATION OPERATION BY LIGHTING
SWITCH ............................................................ .189
EXTERIOR LAMP BATTERY SAVER CONTROL .190
CAN Communication System Description ........... .190
CAN Communication Unit .................................... .191
Schematic ............................................................ .192
Wiring Diagram — ILL — ..................................... .194
Removal and Installation ...................................... .202
ILLUMINATION CONTROL SWITCH ............... .202
GLOVE BOX LAMP .......................................... .202
FRONT DOOR INSIDE ILLUMINATION ........... .202
BULB SPECIFICATIONS ....................................... .203
Headlamp ............................................................. .203
Exterior Lamp ....................................................... .203
Interior Lamp/Illumination ..................................... .203
Page 3896 of 4731
HEADLAMP - XENON TYPE - LT-7
C
D E
F
G H
I
J
L
M A
B
LT
Revision: 2005 July 2005 FX
HEADLAMP - XENON TYPE -PFP:26010
Component Parts and Harness Connector LocationAKS007M9
System DescriptionAKS007MA
Control of the headlamp system operation is dependent upon the position of the combination switch (lighting
switch). When the lighting switch is placed in the 2ND position, the BCM (body control module) receives input
signal requesting the headlamps (and tail lamps) illuminate. This input signal is communicated to the IPDM E/
R (intelligent power distribution module engine room) across the CAN communication lines. The CPU (central
processing unit) located in the IPDM E/R controls the headlamp high and headlamp low relay coils. These
relays, when energized, direct power to the respective headlamps, which then illuminate.
If voltage is applied to a high beam solenoid, the bulb shade will move, even a xenon head lamp bulb comes
out, and a high beam and a low beam are changed.
OUTLINE
Power is supplied at all times
to headlamp high relay, located in IPDM E/R,
to headlamp low relay, located in IPDM E/R, and
to ignition relay, located in IPDM E/R, from battery direct,
through 10A fuse (No. 71, located in IPDM E/R)
to CPU located in IPDM E/R,
through 15A fuse (No. 78, located in IPDM E/R)
to CPU located in IPDM E/R,
through 50A fusible link (letter M, located in fuse, fusible link and relay box)
to BCM terminal 55,
through 15A fuse [No. 22, located in fuse block (J/B)]
to BCM terminal 42,
through 10A fuse [No. 19, located in fuse block (J/B)]
to combination meter terminal 8.
PKIB3472E
Page 3898 of 4731
HEADLAMP - XENON TYPE - LT-9
C
D E
F
G H
I
J
L
M A
B
LT
Revision: 2005 July 2005 FX
to front combination lamp LH terminal 5.
Ground is supplied
to front combination lamp RH terminal 7
through grounds E21, E50 and E51,
to front combination lamp LH terminal 7
through grounds E21, E50 and E51.
With power and ground supplied, the high beam headlamps illuminate.
If voltage is applied to a high beam solenoid, the bulb shade will move, even a xenon head lamp bulb comes
out, and a high beam and a low beam are changed.
The unified meter and A/C amp. that received the high beam request signal by BCM across the CAN commu-
nication makes a high beam indicator lamp turn on in combination meter.
COMBINATION SWITCH READING FUNCTION
Refer to BCS-3, "COMBINATION SWITCH READING FUNCTION" .
EXTERIOR LAMP BATTERY SAVER CONTROL
When the combination switch (lighting switch) is in the 2ND position (ON), and the ignition switch is turned
from ON or ACC to OFF, the battery saver control function is activated.
Under this condition, the headlamps remain illuminated for 5 minutes, then the headlamps are turned OFF.
Exterior lamp battery saver control mode can be changed by the function setting of CONSULT-II.
AUTO LIGHT OPERATION (IF EQUIPPED)
Refer to LT- 5 5 , "System Description" in “AUTO LIGHT SYSTEM”.
VEHICLE SECURITY SYSTEM
The vehicle security system will flash the high beams if the system is triggered. Refer to BL-186, "VEHICLE
SECURITY (THEFT WARNING) SYSTEM" .
XENON HEADLAMP
Xenon type lamps are used for to the low beam headlamps. Xenon bulbs do not use a filament. Instead, they
produce light when a high voltage current is passed between two tungsten electrodes through a mixture of
xenon (an inert gas) and certain other metal halides. In addition to strong lighting power, electronic control of
the power supply gives the headlamps stable quality and tone color.
Followings are some advantages of the xenon type headlamp.
The light produced by the headlamps is white color similar to sunlight that is easy to the eyes.
Light output is nearly double that of halogen headlamps, affording increased area of illumination.
Retroreflected luminance increases and the contrast enhances on the wet road in the rain. That makes
visibility go up more than the increase of the light volume.
Power consumption is approximately 25 percent less than halogen headlamps, reducing battery load.
CAN Communication System DescriptionAKS007MB
CAN (Controller Area Network) is a serial communication line for real time application. It is an on-vehicle mul-
tiplex communication line with high data communication speed and excellent error detection ability. Many elec-
tronic control units are equipped onto a vehicle, and each control unit shares information and links with other
control units during operation (not independent). In CAN communication, control units are connected with 2
communication lines (CAN H line, CAN L line) allowing a high rate of information transmission with less wiring.
Each control unit transmits/receives data but selectively reads required data only.
CAN Communication UnitAKS0080S
Refer to LAN-30, "CAN Communication Unit" .