lock INFINITI FX35 2005 Service Manual

IP-12
INSTRUMENT PANEL ASSEMBLY
Revision: 2005 July 2005 FX
[ ]: Number indicates step in removal procedures.
REMOVAL
(A) Front Kicking Plate (RH/LH)
Remove front kicking plate (RH/LH). Refer to EI-36, "BODY SIDE TRIM" .
(B) Dash Side Finisher (RH/LH)
1. Remove plastics nut.
2. Remove dash side finisher (RH/LH). Refer to EI-36, "
BODY SIDE TRIM" .
(C) Front Pillar Garnish (RH/LH)
Pull to inside of vehicle, disengage metal clips and remove front pillar garnish. Refer to EI-36, "BODY SIDE
TRIM" .
(D) A/T Select Lever Knob
1. Pull down knob cover.
2. Remove lock-pin of select lever knob.
3. Lift up select lever knob and remove it. Refer to AT- 2 3 3 , "
Control Device Removal and Installation" .
(E) Instrument Clock Finisher
1. Insert a remover into side between gaps of instrument clock fin-
isher and pull back to your side.
2. Disconnect clips and harness connector, and remove instrument clock finisher.
(F) A/T Console Finisher
1. Insert a remover into side between gaps of A/T console finisher
and remove by lifting A/T console finisher.
2. Disconnect harness connector.
(G) Console Finisher (RH/LH)
1. Remove screws with power tool.
2. Remove console finisher (RH/LH).
(H) Center Console
1. Remove screws with power tool.
2. Remove console sub-harness
PIIA4997E
PIIA4996E
PIIA5001E

INSTRUMENT PANEL ASSEMBLY IP-13
C
D E
F
G H
J
K L
M A
B
IP
Revision: 2005 July 2005 FX
3. After removing, disassemble, each parts.
CAUTION:
When removing console, be careful not to pull the harness.
(I) Instrument Lower Cover
1. Pull down front instrument lower cover, and disconnect clips.
2. Pull it horizontally, and remove from lower cover pawls.
(J) Instrument Passenger Lower Panel
Remove screws with power tool, and disconnect harness connector,
and remove instrument passenger lower panel.
(K) Instrument Driver Lower Panel
1. Remove bolt and screws with power tool.
2. Remove data link connector.
3. Pull to disengage clip and pawl by removing panel in horizontal direction.
4. Disconnect in-vehicle sensor and each electrical parts.
5. Remove the grommet, and remove hood lock cable.
(L) Steering Column Front Lower Cover
1. Remove screw with power tool.
2. Disengage the tab, then remove steering column front lower cover.
NOTE:

Move the steering column telescopic to the rear most position

Move the steering column tilt to the top position.
(M) Steering Column Lower Cover
1. Remove screws with power tool.
2. Disengage the tab, then remove steering column lower cover.
PIIA5007E
PIIA4995E
PIIA4998E

IP-14
INSTRUMENT PANEL ASSEMBLY
Revision: 2005 July 2005 FX
(N) Steering Column Upper Cover
Remove the steering column upper cover.
(O) Wiper and Washer Switch
Remove wiper and washer switch. Refer to WW-36, "Removal and Installation of Front Wiper and Washer
Switch" .
(P) Lighting and Turn Signal Switch
Remove lighting and turn signal switch. Refer to LT- 11 0 , "LIGHTING AND TURN SIGNAL SWITCH" .
(Q) Steering Lock Escutcheon
Pull back to your side, and remove steering lock escutcheon.
(R) Combination Meter Assembly
1. Remove bolts with power tool, and then remove connector
bracket.
2. Remove bolts with power tool and then disconnect harness con- nector.
CAUTION:
To prevent it from damaged by interference with the combina-
tion meter assembly, protect the combination meter assembly
with cloths.
(S) Instrument Side Panel (RH/LH)
1. Remove screws with power tool.
2. Pull to the side, disconnect clip and pawls and remove instru- ment side panel (RH/LH).
PIIA5002E
PIIA5003E
PIIA5004E

LAN-32
[CAN]
CAN COMMUNICATION
Revision: 2005 July 2005 FX
Ignition switch signal T R R
P range signal T R R
Stop lamp switch signal R T
Fuel consumption monitor signal TR
RT
Turbine revolution signal R T
Output shaft revolution signal R T R
A/C switch signal R T
A/C compressor request signal T R
A/C compressor feedback signal T R
Blower fan motor switch signal R T
A/C switch/indicator signal TR
RT
Cooling fan speed request signal T R
Position light request signal R T R R
Low beam request signal T R
Low beam status signal R T
High beam request signal T R R
High beam status signal R T
Front fog light request signal T R
Day time running light request
signal TR
Turn LED burnout status signal R T
Vehicle speed signal RR T
RRRR T R
Sleep wake up signal T R R
Door switch signal R T R R R
Turn indicator signal T R R
Key fob ID signal T R
Key fob door unlock signal T R
Oil pressure switch signal RT
TR
Buzzer output signal T R
Fuel level sensor signal R T
Fuel level low warning signal R T
ASCD SET lamp signal T R
ASCD CRUISE lamp signal T R
Malfunction indicator lamp signal T R
ASCD operation signal T R
ASCD OD cancel request signal T R Signals ECM TCM
Dis-
play unit BCM Steer-
ing
angle
sensor LDW
cam-
era unit Unified
meter and
A/C
amp. ABS
actua-
tor and elec-
tric unit (con-trol
unit) Driver
seat
control unit IPDM
E/R

LAN-36
[CAN]
CAN COMMUNICATION
Revision: 2005 July 2005 FX
Vehicle speed signal RRRT
RRRRR TRR
Sleep wake up signal TR R
TR
Door switch signal R R T R R R
Turn indicator signal T R R
Key fob ID signal T R
Key fob door unlock sig-
nal TR
Oil pressure switch sig-
nal RT
TR
Buzzer output signal TR
TR
TR
Fuel level sensor signal R T
Fuel level low warning
signal RT
Malfunctioning indicator
lamp signal TR
ICC operation signal R T
Front wiper request sig-
nal RT R
Front wiper stop position
signal RT
Rear window defogger
switch signal TR
Rear window defogger
control signal RR R T
Hood switch signal R T
Theft warning horn
request signal TR
Horn chirp signal T R
Steering angle sensor
signal TR
Tire pressure signal T R
ABS warning lamp signal R T
VDC OFF indicator lamp
signal RT
SLIP indicator lamp sig-
nal RT
Brake warning lamp sig-
nal RT
Signals ECM TCM
Dis-
play
con-
trol
unit ICC
unit Intelli-
gent Key unit BCM St e e r-
ing
angle
sen- sor LDW
cam- era
unit Uni-
fied
meter and
A/C
amp. ICC
sen-
sor ABS
actu- ator and
elec- tric
unit
(con- trol
unit) Driver
seat
con-
trol
unit IPDM
E/R

CAN COMMUNICATION LAN-37
[CAN]
C
D E
F
G H
I
J
L
M A
B
LAN
Revision: 2005 July 2005 FX
System setting signal TR R
RT T
Distance to empty signal R T
Parking brake switch sig-
nal RT
Door lock/unlock request
signal TR
Door lock/unlock status
signal RT
Starter permission signal T R
Back door open request
signal TR
Power window open
request signal TR
Alarm request signal T R
Key warning signal T R
ICC sensor signal R T
ICC warning lamp signal T R
ICC system display sig-
nal TR
Current gear position sig-
nal TR R
ICC steering switch sig-
nal TR
ASCD operation signal T R
ASCD OD cancel
request signal TR
ICC OD cancel request
signal RT
A/T CHECK indicator
lamp signal TR
A/T position indicator
lamp signal TR
A/T shift schedule
change demand signal R
T
Manual mode signal R T
Not manual mode signal R T
Manual mode shift up
signal RT
Manual mode shift down
signal RT
Manual mode indicator
signal TR R
Signals ECM TCM
Dis-
play
con-
trol
unit ICC
unit Intelli-
gent Key unit BCM Ste er-
ing
angle
sen- sor LDW
cam- era
unit Uni-
fied
meter and
A/C
amp. ICC
sen-
sor ABS
actu- ator and
elec- tric
unit
(con- trol
unit) Driver
seat
con-
trol
unit IPDM
E/R

LAN-40
[CAN]
CAN COMMUNICATION
Revision: 2005 July 2005 FX
A/C switch/indicator signal TR
RT
Cooling fan speed request sig-
nal T
R
Position light request signal R T R R
Low beam request signal T R
Low beam status signal R T
High beam request signal T R R
High beam status signal R T
Front fog light request signal T R
Day time running light request
signal TR
Turn LED burnout status signal R T
Vehicle speed signal RRRT
RRR R T R
Sleep wake up signal T R R
Door switch signal R T R R R
Turn indicator signal T R R
Key fob ID signal T R
Key fob door unlock signal T R
Oil pressure switch signal RT
TR
Buzzer output signal T R
Fuel level sensor signal R T
Fuel level low warning signal R T
ASCD SET lamp signal T R
ASCD CRUISE lamp signal T R
Malfunction indicator lamp sig-
nal TR
Front wiper request signal T R
Front wiper stop position signal R T
Rear window defogger switch
signal TR
Rear window defogger control
signal RRR T
Hood switch signal R T
Theft warning horn request sig-
nal TR
Horn chirp signal T R
Steering angle sensor signal T R Signals ECM TCM
Dis-
play
unit AW D
con- trol
unit BCM Steer-
ing
angle
sensor LDW
cam- era
unit Uni-
fied
meter and
A/C
amp. ABS
actua- tor
and
elec- tric
unit
(con- trol
unit) Driver
seat
con-
trol
unit IPDM
E/R

LAN-44
[CAN]
CAN COMMUNICATION
Revision: 2005 July 2005 FX
Day time running
light request signal TR
Turn LED burnout
status signal RT
Vehicle speed signal RR R R T
RR R R R T R R
Sleep wake up signal TR R
TR
Door switch signal R R T R R R
Turn indicator signal T R R
Key fob ID signal T R
Key fob door unlock
signal TR
Oil pressure switch
signal RT
TR
Buzzer output signal TR
TR
TR
Fuel level sensor sig-
nal RT
Fuel level low warn-
ing signal RT
Malfunction indicator
lamp signal TR
ICC operation signal R T
Front wiper request
signal RT R
Front wiper stop
position signal RT
Rear window defog-
ger switch signal TR
Rear window defog-
ger control signal RR R T
Hood switch signal R T
Theft warning horn
request signal TR
Horn chirp signal T R
Steering angle sen-
sor signal TR
Tire pressure signal T R
ABS warning lamp
signal RT
Signals ECM TCM
Dis-
play
con-
trol
unit AW D
con- trol
unit ICC
unit Intel-
ligent Key unit BCM Steer-
ing
angle
sen- sor LDW
cam- era
unit Uni-
fied
meter and
A/C
amp. ICC
sen-
sor ABS
actu- ator and
elec- tric
unit
(con- trol
unit) Driver
seat
con-
trol
unit IPDM
E/R

CAN COMMUNICATION LAN-45
[CAN]
C
D E
F
G H
I
J
L
M A
B
LAN
Revision: 2005 July 2005 FX
VDC OFF indicator
lamp signal RT
SLIP indicator lamp
signal RT
Brake warning lamp
signal RT
System setting signal TR R
RT T
AWD warning lamp
signal TR
Distance to empty
signal RT
Parking brake switch
signal RR T
Door lock/unlock
request signal TR
Door lock/unlock sta-
tus signal RT
Starter permission
signal TR
Back door open
request signal TR
Power window open
request signal TR
Alarm request signal T R
Key warning signal T R
ICC sensor signal R T
ICC warning lamp
signal TR
ICC system display
signal TR
Current gear posi-
tion signal TR R
ICC steering switch
signal TR
ASCD operation sig-
nal TR
ASCD OD cancel
request signal TR
ICC OD cancel
request signal RT
A/T CHECK indica-
tor lamp signal TR
A/T position indica-
tor lamp signal TR
Signals ECM TCM
Dis-
play
con-
trol
unit AWD
con- trol
unit ICC
unit Intel-
ligent Key unit BCM Steer-
ing
angle
sen- sor LDW
cam- era
unit Uni-
fied
meter and
A/C
amp. ICC
sen-
sor ABS
actu- ator and
elec- tric
unit
(con- trol
unit) Driver
seat
con-
trol
unit IPDM
E/R

HEADLAMP - XENON TYPE - LT-7
C
D E
F
G H
I
J
L
M A
B
LT
Revision: 2005 July 2005 FX
HEADLAMP - XENON TYPE -PFP:26010
Component Parts and Harness Connector LocationAKS007M9
System DescriptionAKS007MA
Control of the headlamp system operation is dependent upon the position of the combination switch (lighting
switch). When the lighting switch is placed in the 2ND position, the BCM (body control module) receives input
signal requesting the headlamps (and tail lamps) illuminate. This input signal is communicated to the IPDM E/
R (intelligent power distribution module engine room) across the CAN communication lines. The CPU (central
processing unit) located in the IPDM E/R controls the headlamp high and headlamp low relay coils. These
relays, when energized, direct power to the respective headlamps, which then illuminate.
If voltage is applied to a high beam solenoid, the bulb shade will move, even a xenon head lamp bulb comes
out, and a high beam and a low beam are changed.
OUTLINE
Power is supplied at all times

to headlamp high relay, located in IPDM E/R,

to headlamp low relay, located in IPDM E/R, and

to ignition relay, located in IPDM E/R, from battery direct,

through 10A fuse (No. 71, located in IPDM E/R)

to CPU located in IPDM E/R,

through 15A fuse (No. 78, located in IPDM E/R)

to CPU located in IPDM E/R,

through 50A fusible link (letter M, located in fuse, fusible link and relay box)

to BCM terminal 55,

through 15A fuse [No. 22, located in fuse block (J/B)]

to BCM terminal 42,

through 10A fuse [No. 19, located in fuse block (J/B)]

to combination meter terminal 8.
PKIB3472E