removal INFINITI FX35 2006 Service Manual
[x] Cancel search | Manufacturer: INFINITI, Model Year: 2006, Model line: FX35, Model: INFINITI FX35 2006Pages: 4462, PDF Size: 57.74 MB
Page 3353 of 4462
INSTRUMENT PANEL ASSEMBLY IP-11
C
D E
F
G H
J
K L
M A
B
IP
Revision: 2006 December 2006 FX35/FX45
Removal and InstallationNIS001UF
WORK STEP
When removing instrument panel and pad, combination meter, display unit and audio unit, center console take
steps in the order shown by the numbers below.
CAUTION:
Disconnect both battery cables in advance.
Disconnect air bag system line in advance.
Never temper with air bag lid or force air bag lid to open, as this may adversely affect air bag per-
formance.
Be careful not to scratch pad and other parts.
[ ]: Number indicates step in removal procedures. 1. Front defroster grille (RH) 2. Instrument panel and pad 3. Front defroster grille (LH)
4. Combination meter assembly 5. Steering lock escutcheon 6. Side ventilation (LH)
7. Display unit and audio unit 8. Wiper and washer switch 9. Rubber
10. Lighting and turn signal switch 11. Combination meter bracket 12. Cluster lid C
13. Steering column upper cover 14. Steering column lower cover 15. Steering column front lower cover
16. Instrument side panel (LH) 17. Instrument clock finisher assembly 18. A/T console finisher assembly
19. Instrument driver lower panel 20. Center console 21. Instrument side panel (RH)
22. Instrument lower cover 23. Instrument passenger lower panel 24. Side ventilation (RH) metal clip clip pawl
Parts Reference
page Instrument
panel and pad Combination
meter Display unit and
audio unit Center console
(A) Front kicking plate (RH/LH) EI-39
[ 1 ] [ 1 ]
(B) Dash side finisher (RH/LH) EI-38
[ 2 ] [ 2 ]
(C) Front pillar garnish (RH/LH) EI-39
[ 3 ]
(D) A/T select lever knob AT- 2 2 9
[ 4 ] [ 1 ]
(E) Instrument clock finisher assembly IP-12
[ 5 ] [ 2 ]
(F) A/T console finisher assembly IP-12
[ 6 ] [ 3 ]
(G) Instrument side panel (RH/LH) IP-12
[ 7 ] [ 4 ]
(H) Center console IP-12
[ 8 ] [ 5 ]
(I) Instrument lower cover IP-13
[ 9 ]
(J) Instrument passenger lower panel IP-13
[10]
(K) Instrument driver lower panel IP-13
[11] [ 3 ]
(L) Steering column front lower cover IP-13
[12] [ 4 ]
(M) Steering column lower cover IP-13
[13] [ 5 ]
(N) Steering column upper cover IP-14
[14] [ 6 ]
(O) Wiper and washer switch IP-14
[15] [ 7 ]
(P) Lighting and turn signal switch IP-14
[16] [ 8 ]
(Q) Steering lock escutcheon IP-14
[17] [ 9 ]
(R) Combination meter assembly IP-14
[18] [10]
(S) Cluster lid C IP-14
[19] [ 1 ]
(T) Display unit and audio unit IP-15
[20] [ 2 ]
(U) Front defroster grille (RH/LH) IP-15
[21]
(V) Combination meter bracket IP-15
[22]
(W) Side ventilation (RH/LH) IP-15
[23]
(X) Instrument panel and pad IP-15
[24]
Page 3354 of 4462
IP-12
INSTRUMENT PANEL ASSEMBLY
Revision: 2006 December 2006 FX35/FX45
REMOVAL
(A) Front Kicking Plate (RH/LH)
Remove front kicking plate (RH/LH). Refer to EI-37, "BODY SIDE TRIM" .
(B) Dash Side Finisher (RH/LH)
1. Remove plastics nut.
2. Remove dash side finisher (RH/LH). Refer to EI-37, "
BODY SIDE TRIM" .
(C) Front Pillar Garnish (RH/LH)
Pull to inside of vehicle, disengage metal clips and remove front pillar garnish. Refer to EI-37, "BODY SIDE
TRIM" .
(D) A/T Select Lever Knob
1. Pull down knob cover.
2. Remove lock-pin of select lever knob.
3. Lift up select lever knob and remove select lever knob. Refer to AT- 2 2 9 , "
Control Device Removal and
Installation" .
(E) Instrument Clock Finisher
1. Remove screw and then pull back to your side of instrument
clock finisher.
2. Disconnect clips and harness connector, and remove instrument clock finisher.
(F) A/T Console Finisher
1. Insert a remover into side between gaps of A/T console finisher assembly and remove by lifting A/T console finisher.
2. Disconnect harness connector.
(G) Instrument Side Panel (RH/LH)
1. Remove screws with power tool.
2. Pull to the side, disconnect clip and pawls and remove instru- ment side panel (RH/LH).
(H) Center Console
1. Remove screws with power tool.
2. Remove console sub-harness
PIIB8535E
PIIB8534E
PIIB8536E
Page 3356 of 4462
IP-14
INSTRUMENT PANEL ASSEMBLY
Revision: 2006 December 2006 FX35/FX45
(N) Steering Column Upper Cover
Remove the steering column upper cover.
(O) Wiper and Washer Switch
Remove wiper and washer switch. Refer to WW-37, "Removal and Installation of Front Wiper and Washer
Switch" .
(P) Lighting and Turn Signal Switch
Remove lighting and turn signal switch. Refer to LT- 111 , "LIGHTING AND TURN SIGNAL SWITCH" .
(Q) Steering Lock Escutcheon
Pull back to your side, and remove steering lock escutcheon.
(R) Combination Meter Assembly
1. Remove bolts with power tool, and then remove connector
bracket.
2. Remove bolts with power tool and then disconnect harness con- nector.
CAUTION:
To prevent it from damaged by interference with the combina-
tion meter assembly, protect the combination meter assembly
with cloths.
(S) Cluster Lid C
1. Insert a remover into gap between instrument panel and pad, pull back to your side, and disconnect metal clips below.
2. Disconnect harness connectors, and remove cluster lid C.
CAUTION:
Cover surroundings with cloth to avoid scratches or damages.
PIIA5002E
PIIA5003E
PIIB8533E
Page 3357 of 4462
INSTRUMENT PANEL ASSEMBLY IP-15
C
D E
F
G H
J
K L
M A
B
IP
Revision: 2006 December 2006 FX35/FX45
(T) Display Unit and Audio Unit
1. Remove screws with power tool.
2. Disconnect harness connector, and remove display unit and audio unit.
CAUTION:
Unit is heavy, so be careful not to pinch your fingers when
working.
(U) Front Defroster Grille (RH/LH)
Insert a remover into gaps between front defroster grille (RH/LH) and
instrument panel and pad, lift front defroster grille up, and remove
front defroster grille (RH/LH).
(V) Combination Meter Bracket
1. Remove bolts.
2. The installation bolts of the harness clip and steering column assembly is removed, steering column assembly is pulled back-
ward, and set combination meter bracket free from the instru-
ment panel and pad. Refer to PS-12, "
STEERING COLUMN" .
(W) Side Ventilation (RH/LH)
1. Insert a remover into gaps between instrument panel and pad,
pull back to your side, and disconnect metal clips below.
2. Disconnect door mirror switch harness connectors, and remove side ventilation (RH/LH).
(X) Instrument Panel and Pad
1. Remove bolts and screws.
2. Remove front passenger air bag module. Refer to SRS-42, "
Removal and Installation" .
3. Disconnect harness connectors, and remove instrument panel and pad from passenger door opening por- tion.
INSTALLATION
Install in the reverse order of removal.
PIIB1335E
PIIA5009E
PIIA5010E
PIIA5011E
Page 3363 of 4462
![INFINITI FX35 2006 Service Manual PRECAUTIONS LAN-3
[CAN]
C
D E
F
G H
I
J
L
M A
B
LAN
Revision: 2006 December 2006 FX35/FX45
[CAN]PRECAUTIONSPFP:00001
Precautions for Supplemental Restraint System (SRS) “AIR BAG” and](/img/42/57019/w960_57019-3362.png "INFINITI FX35 2006 Service Manual PRECAUTIONS LAN-3
[CAN]
C
D E
F
G H
I
J
L
M A
B
LAN
Revision: 2006 December 2006 FX35/FX45
[CAN]PRECAUTIONSPFP:00001
Precautions for Supplemental Restraint System (SRS) “AIR BAG” and")
PRECAUTIONS LAN-3
[CAN]
C
D E
F
G H
I
J
L
M A
B
LAN
Revision: 2006 December 2006 FX35/FX45
[CAN]PRECAUTIONSPFP:00001
Precautions for Supplemental Restraint System (SRS) “AIR BAG” and “SEAT
BELT PRE-TENSIONER”
NKS00345
The Supplemental Restraint System such as “AIR BAG” and “SEAT BELT PRE-TENSIONER”, used along
with a front seat belt, helps to reduce the risk or severity of injury to the driver and front passenger for certain
types of collision. This system includes seat belt switch inputs and dual stage front air bag modules. The SRS
system uses the seat belt switches to determine the front air bag deployment, and may only deploy one front
air bag, depending on the severity of a collision and whether the front occupants are belted or unbelted.
Information necessary to service the system safely is included in the SRS and SB section of this Service Man-
ual.
WARNING:
To avoid rendering the SRS inoperative, which could increase the risk of personal injury or death
in the event of a collision which would result in air bag inflation, all maintenance must be per-
formed by an authorized NISSAN/INFINITI dealer.
Improper maintenance, including incorrect removal and installation of the SRS, can lead to per-
sonal injury caused by unintentional activation of the system. For removal of Spiral Cable and Air
Bag Module, see the SRS section.
Do not use electrical test equipment on any circuit related to the SRS unless instructed to in this
Service Manual. SRS wiring harnesses can be identified by yellow and/or orange harnesses or
harness connectors.
Precautions When Using CONSULT-IINKS00346
When connecting CONSULT-II to data link connector, connect them through CONSULT-II CONVERTER.
CAUTION:
If CONSULT-II is used with no connection of CONSULT-II CONVERTER, malfunctions might be
detected in self-diagnosis depending on control unit which carry out CAN communication.
CHECK POINTS FOR USING CONSULT-II
1. Has CONSULT-II been used without connecting CONSULT-II CONVERTER on this vehicle?
–If YES, GO TO 2.
–If NO, GO TO 5.
2. Is there any indication other than indications relating to CAN communication system in the self-diagnosis results?
–If YES, GO TO 3.
–If NO, GO TO 4.
3. Based on self-diagnosis results unrelated to CAN communication, carry out the inspection.
4. Malfunctions may be detected in self-diagnosis depending on control units carrying out CAN communica- tion. Therefore, erase the self-diagnosis results.
5. Diagnose CAN communication system. Refer to LAN-5, "
TROUBLE DIAGNOSES WORK FLOW" .
Precautions For Trouble DiagnosisNKS00347
CAN SYSTEM
Do not apply voltage of 7.0 V or higher to the measurement terminals.
Use the tester with its open terminal voltage being 7.0 V or less.
Be sure to turn ignition switch OFF and disconnect the battery cable from the negative terminal before
checking the circuit.
Page 3365 of 4462
![INFINITI FX35 2006 Service Manual TROUBLE DIAGNOSES WORK FLOW LAN-5
[CAN]
C
D E
F
G H
I
J
L
M A
B
LAN
Revision: 2006 December 2006 FX35/FX45
TROUBLE DIAGNOSES WORK FLOWPFP:00004
When Displaying CAN Communication System Err](/img/42/57019/w960_57019-3364.png "INFINITI FX35 2006 Service Manual TROUBLE DIAGNOSES WORK FLOW LAN-5
[CAN]
C
D E
F
G H
I
J
L
M A
B
LAN
Revision: 2006 December 2006 FX35/FX45
TROUBLE DIAGNOSES WORK FLOWPFP:00004
When Displaying CAN Communication System Err")
TROUBLE DIAGNOSES WORK FLOW LAN-5
[CAN]
C
D E
F
G H
I
J
L
M A
B
LAN
Revision: 2006 December 2006 FX35/FX45
TROUBLE DIAGNOSES WORK FLOWPFP:00004
When Displaying CAN Communication System ErrorsNKS00349
WHEN A MALFUNCTION IS DETECTED BY CAN COMMUNICATION SYSTEM
CAN communication line is open. (CAN-H, CAN-L, or both)
CAN communication line is shorted. (Ground, between CAN lines, or other harnesses)
The areas related to CAN communication of unit is malfunctioning.
WHEN A MALFUNCTION IS DETECTED EXCEPT CAN COMMUNICATION SYSTEM
Removal and installation of parts: When the units that perform CAN communication or the sensors related
to CAN communication are removed and installed, malfunction may be detected (or DTC other than CAN
communication may be detected).
Fuse blown out (removed): CAN communication of the unit may be stopped at such time.
Low voltage: If the voltage decreases because of battery discharge when IGN is ON, malfunction may be
detected by self-diagnosis according to the units.
Page 3556 of 4462
![INFINITI FX35 2006 Service Manual LAN-196
[CAN]
TROUBLE DIAGNOSIS FOR SYSTEM
Revision: 2006 December 2006 FX35/FX45
BCM Circuit InspectionNKS00394
1. CHECK CONNECTOR
1. Turn ignition switch OFF.
2. Disconnect the battery cable from](/img/42/57019/w960_57019-3555.png "INFINITI FX35 2006 Service Manual LAN-196
[CAN]
TROUBLE DIAGNOSIS FOR SYSTEM
Revision: 2006 December 2006 FX35/FX45
BCM Circuit InspectionNKS00394
1. CHECK CONNECTOR
1. Turn ignition switch OFF.
2. Disconnect the battery cable from")
LAN-196
[CAN]
TROUBLE DIAGNOSIS FOR SYSTEM
Revision: 2006 December 2006 FX35/FX45
BCM Circuit InspectionNKS00394
1. CHECK CONNECTOR
1. Turn ignition switch OFF.
2. Disconnect the battery cable from the negative terminal.
3. Check terminals and connector of BCM for damage, bend and loose connection (control module side and harness side).
OK or NG
OK >> GO TO 2.
NG >> Repair terminal or connector.
2. CHECK HARNESS FOR OPEN CIRCUIT
1. Disconnect BCM connector.
2. Check resistance between BCM harness connector terminals.
OK or NG
OK >> Replace BCM. Refer to BCS-15, "Removal and Installa-
tion of BCM" .
NG >> Repair harness between BCM and data link connector.
Steering Angle Sensor Circuit InspectionNKS00395
1. CHECK CONNECTOR
1. Turn ignition switch OFF.
2. Disconnect the battery cable from the negative terminal.
3. Check terminals and connector of steering angle sensor for damage, bend and loose connection (sensor side and harness side).
OK or NG
OK >> GO TO 2.
NG >> Repair terminal or connector.
2. CHECK HARNESS FOR OPEN CIRCUIT
1. Disconnect steering angle sensor connector.
2. Check resistance between steering angle sensor harness con- nector terminals.
OK or NG
OK >> Replace steering angle sensor.
NG >> Repair harness between steering angle sensor and data link connector.
BCM connector Terminals Resistance
(Approx.)
M3 39 40 54 – 66 Ω
SKIA6869E
Steering angle
sensor connector Terminals Resistance
(Approx.)
M14 4 5 54 – 66 Ω
PKIA9864E
Page 3563 of 4462
LT-1
LIGHTING SYSTEM
K ELECTRICAL
CONTENTS
C
D E
F
G H
I
J
L
M
SECTION LT
A
B
LT
Revision: 2006 December 2006 FX35/FX45
LIGHTING SYSTEM
PRECAUTIONS ..................................................... ..... 5
Precautions for Supplemental Restraint System
(SRS) “AIR BAG” and “SEAT BELT PRE-TEN-
SIONER” ............................................................. ..... 5
General Precautions for Service Operations ....... ..... 6
HEADLAMP - XENON TYPE - .............................. ..... 7
Component Parts and Harness Connector Location ..... 7
System Description ............................................. ..... 7
OUTLINE .......................................................... ..... 7
HEADLAMP OPERATION ............................... ..... 8
COMBINATION SWITCH READING FUNCTION ..... 9
EXTERIOR LAMP BATTERY SAVER CONTROL ..... 9
AUTO LIGHT OPERATION (IF EQUIPPED) .... ..... 9
VEHICLE SECURITY SYSTEM ....................... ..... 9
XENON HEADLAMP ........................................ ..... 9
CAN Communication System Description ........... ..... 9
CAN Communication Unit ................................... ..... 9
Schematic ........................................................... ... 10
Wiring Diagram — H/LAMP — ............................ .... 11
Terminals and Reference Values for BCM .......... ... 15
Terminals and Reference Values for IPDM E/R .. ... 16
How to Proceed With Trouble Diagnosis ............. ... 17
Preliminary Check ............................................... ... 17
CHECK POWER SUPPLY AND GROUND CIR-
CUIT ................................................................. ... 17
CONSULT-II Functions (BCM) ............................ ... 19
CONSULT-II BASIC OPERATION .................... ... 19
WORK SUPPORT ............................................ ... 19
DATA MONITOR .............................................. ... 19
ACTIVE TEST .................................................. ... 20
CONSULT-II Functions (IPDM E/R) .................... ... 21
CONSULT-II BASIC OPERATION .................... ... 21
DATA MONITOR .............................................. ... 21
ACTIVE TEST .................................................. ... 22
Headlamp Does Not Change To High Beam (Both
Sides) .................................................................. ... 22
Headlamp Does Not Change To High Beam (One
Side) .................................................................... ... 24
Headlamp Low Beam Does Not Illuminate (Both
Sides) .................................................................. ... 25 Headlamp Low Beam Does Not Illuminate (One
Side) .................................................................... ... 28
Headlamp RH Low Beam and High Beam Does Not
Illuminate ............................................................. ... 29
Headlamp LH Low Beam and High Beam Does Not
Illuminate ............................................................. ... 30
Headlamps Do Not Turn OFF .............................. ... 31
General Information for Xenon Headlamp Trouble
Diagnosis ............................................................. ... 33
Caution: ............................................................... ... 33
Xenon Headlamp Trouble Diagnosis ................... ... 33
Aiming Adjustment ............................................... ... 34
PREPARATION BEFORE ADJUSTING ........... ... 34
LOW BEAM AND HIGH BEAM ........................ ... 34
ADJUSTMENT USING AN ADJUSTMENT
SCREEN (LIGHT/DARK BORDERLINE) ......... ... 35
Bulb Replacement ............................................... ... 35
HEADLAMP HIGH/LOW BEAM ....................... ... 35
DAYTIME/PARKING LAMP .............................. ... 36
FRONT TURN SIGNAL LAMP ......................... ... 36
FRONT SIDE MARKER LAMP ........................ ... 36
Removal and Installation ..................................... ... 36
REMOVAL ........................................................ ... 36
INSTALLATION ................................................ ... 37
Disassembly and Assembly ................................. ... 37
DISASSEMBLY ................................................ ... 37
ASSEMBLY ...................................................... ... 37
DAYTIME LIGHT SYSTEM .................................... ... 39
Component Parts and Harness Connector Location ... 39
System Description .............................................. ... 39
OUTLINE .......................................................... ... 39
DAYTIME LIGHT OPERATION ........................ ... 40
COMBINATION SWITCH READING FUNCTION ... 40
AUTO LIGHT OPERATION .............................. ... 40
CAN Communication System Description ........... ... 40
CAN Communication Unit .................................... ... 40
Schematic ............................................................ ... 41
Wiring Diagram — DTRL — ................................ ... 42
Terminals and Reference Values for BCM ........... ... 46
How to Proceed With Trouble Diagnosis ............. ... 48
Page 3564 of 4462
LT-2Revision: 2006 December 2006 FX35/FX45 Preliminary Check ...............................................
... 49
CHECK POWER SUPPLY AND GROUND CIR-
CUIT ................................................................. ... 49
INSPECTION PARKING BRAKE SWITCH CIR-
CUIT ................................................................. ... 50
CONSULT-II Functions (BCM) ............................. ... 51
CONSULT-II BASIC OPERATION .................... ... 51
DATA MONITOR ............................................... ... 51
ACTIVE TEST .................................................. ... 52
Daytime Light Control Does Not Operate Properly ... 53
Aiming Adjustment ............................................... ... 55
Bulb Replacement ............................................... ... 55
Removal and Installation ..................................... ... 55
Disassembly and Assembly ................................. ... 55
AUTO LIGHT SYSTEM .......................................... ... 56
Component Parts and Harness Connector Location ... 56
System Description .............................................. ... 56
OUTLINE .......................................................... ... 56
COMBINATION SWITCH READING FUNCTION ... 57
DELAY TIMER FUNCTION .............................. ... 57
CAN Communication System Description ........... ... 57
CAN Communication Unit .................................... ... 57
Major Components and Functions ....................... ... 57
Schematic ............................................................ ... 58
Wiring Diagram — AUTO/L — ............................. ... 59
Terminals and Reference Values for BCM ........... ... 62
Terminals and Reference Values for IPDM E/R ... ... 63
How to Proceed With Trouble Diagnosis ............. ... 63
Preliminary Check ............................................... ... 64
SETTING CHANGE FUNCTIONS .................... ... 64
CHECK POWER SUPPLY AND GROUND CIR-
CUIT ................................................................. ... 64
CONSULT-II Functions (BCM) ............................. ... 66
CONSULT-II BASIC OPERATION .................... ... 66
WORK SUPPORT ............................................ ... 66
DATA MONITOR ............................................... ... 66
ACTIVE TEST .................................................. ... 68
CONSULT-II Functions (IPDM E/R) ..................... ... 68
CONSULT-II BASIC OPERATION .................... ... 68
DATA MONITOR ............................................... ... 68
ACTIVE TEST .................................................. ... 69
Symptom Chart .................................................... ... 69
Lighting Switch Inspection ................................... ... 69
Optical sensor System Inspection ....................... ... 70
Removal and Installation of Optical Sensor ......... ... 72
REMOVAL ........................................................ ... 72
INSTALLATION ................................................. ... 72
HEADLAMP AIMING CONTROL ........................... ... 73
Schematic ............................................................ ... 73
Wiring Diagram — H/AIM — ................................ ... 74
Removal and Installation ..................................... ... 77
REMOVAL ........................................................ ... 77
INSTALLATION ................................................. ... 77
Switch Circuit Inspection ..................................... ... 77
FRONT FOG LAMP ............................................... ... 78
Component Parts and Harness Connector Location ... 78
System Description .............................................. ... 78
OUTLINE .......................................................... ... 78
FRONT FOG LAMP OPERATION .................... ... 79 COMBINATION SWITCH READING FUNCTION
... 79
EXTERIOR LAMP BATTERY SAVER CONTROL ... 79
CAN Communication System Description ........... ... 79
CAN Communication Unit .................................... ... 79
Wiring Diagram — F/FOG — ............................... ... 80
Terminals and Reference Values for BCM ........... ... 82
Terminals and Reference Values for IPDM E/R ... ... 82
How to Proceed With Trouble Diagnosis ............. ... 83
Preliminary Check ................................................ ... 83
CHECK POWER SUPPLY AND GROUND CIR-
CUIT .................................................................. ... 83
CONSULT-II Functions (BCM) ............................. ... 84
CONSULT-II Functions (IPDM E/R) ..................... ... 84
Front Fog Lamps Do Not Illuminate (Both Sides) ... 85
Front Fog Lamp Does Not Illuminate (One Side) . ... 87
Aiming Adjustment ............................................... ... 88
Bulb Replacement ................................................ ... 89
Removal and Installation ...................................... ... 89
REMOVAL ......................................................... ... 89
INSTALLATION ................................................. ... 89
TURN SIGNAL AND HAZARD WARNING LAMPS ... 90
Component Parts and Harness Connector Location ... 90
System Description .............................................. ... 90
TURN SIGNAL OPERATION ............................ ... 90
HAZARD LAMP OPERATION .......................... ... 91
REMOTE CONTROL ENTRY SYSTEM OPER-
ATION ............................................................... ... 92
COMBINATION SWITCH READING FUNCTION ... 93
CAN Communication System Description ........... ... 93
CAN Communication Unit .................................... ... 93
Schematic ............................................................ ... 94
Wiring Diagram — TURN — ................................ ... 95
Terminals and Reference Values for BCM ........... ... 98
Terminals and Reference Value for Rear Combina-
tion Lamp Control Unit ......................................... ... 99
How to Proceed With Trouble Diagnosis ............. .102
Preliminary Check ................................................ .102
CHECK POWER SUPPLY AND GROUND CIR-
CUIT .................................................................. .102
CONSULT-II Functions (BCM) ............................. .104
CONSULT-II BASIC OPERATION .................... .104
DATA MONITOR ............................................... .104
ACTIVE TEST ................................................... .104
Turn Signal Lamp Does Not Operate ................... .105
Rear Turn Signal Lamp Does Not Operate .......... .106
Hazard Warning Lamp Does Not Operate But Turn
Signal Lamp Operate ........................................... .108
Bulb Replacement (Front Turn Signal Lamp) ....... .110
Bulb Replacement (Rear Turn Signal Lamp) ....... .110
Removal and Installation of Front Turn Signal Lamp .110
Removal and Installation of Rear Turn Signal Lamp .110
Removal and Installation of Rear Combination
Lamp Control Unit ................................................ .110
REMOVAL ......................................................... .110
INSTALLATION ................................................. .110
LIGHTING AND TURN SIGNAL SWITCH ............. . 111
Removal and Installation ...................................... . 111
REMOVAL ......................................................... . 111
INSTALLATION ................................................. . 111
Page 3565 of 4462
LT-3
C
D E
F
G H
I
J
L
M A
B
LT
Revision: 2006 December 2006 FX35/FX45 HAZARD SWITCH .................................................
..112
Removal and Installation ..................................... .. 112
REMOVAL ........................................................ .. 112
INSTALLATION ................................................ .. 112
COMBINATION SWITCH ....................................... ..113
Wiring Diagram — COMBSW — ......................... .. 113
Combination Switch Reading Function ............... .. 114
Terminals and Reference Values for BCM .......... .. 114
CONSULT-II Functions (BCM) ............................ .. 119
CONSULT-II BASIC OPERATION .................... .. 119
DATA MONITOR .............................................. .. 119
Combination Switch Inspection ........................... . 120
Removal and Installation ..................................... . 122
STOP LAMP .......................................................... . 123
Component Parts and Harness Connector Location . 123
System Description ............................................. . 123
Schematic ........................................................... . 124
Wiring Diagram — STOP/L — ............................. . 125
Terminals and Reference Value for Rear Combina-
tion Lamp Control Unit ........................................ . 128
Stop Lamp Does Not Operate ............................. . 128
High-Mounted Stop Lamp ................................... . 130
BULB REPLACEMENT, REMOVAL AND
INSTALLATION ................................................ . 130
Stop Lamp ........................................................... . 130
BULB REPLACEMENT .................................... . 130
REMOVAL AND INSTALLATION ..................... . 130
Rear Combination Lamp Control Unit ................. . 130
REMOVAL AND INSTALLATION ..................... . 130
BACK-UP LAMP ................................................... . 131
Wiring Diagram — BACK/L — ............................ . 131
Bulb Replacement ............................................... . 132
Removal and Installation ..................................... . 132
PARKING, LICENSE PLATE AND TAIL LAMPS .. . 133
Component Parts and Harness Connector Location . 133
System Description ............................................. . 133
OUT LINE ......................................................... . 133
OPERATION BY LIGHTING SWITCH ............. . 134
COMBINATION SWITCH READING FUNCTION . 135
EXTERIOR LAMP BATTERY SAVER CONTROL . 135
CAN Communication System Description ........... . 135
CAN Communication Unit ................................... . 135
Schematic ........................................................... . 136
Wiring Diagram — TAIL/L — ............................... . 137
Terminals and Reference Values for BCM .......... . 142
Terminals and Reference Values for IPDM E/R .. . 142
Terminals and Reference Value for Rear Combina-
tion Lamp Control Unit ........................................ . 144
How to Proceed With Trouble Diagnosis ............. . 144
Preliminary Check ............................................... . 144
CHECK POWER SUPPLY AND GROUND CIR-
CUIT ................................................................. . 144
CONSULT-II Functions (BCM) ............................ . 145
CONSULT-II Functions (IPDM E/R) .................... . 145
Parking, License Plate and Side Marker Lamps Do
Not Illuminate ...................................................... . 145
Tail Lamp Does Not Operate ............................... . 151
Parking, License Plate, Side Maker and Tail Lamps
Do Not Turn OFF (After Approx. 10 Minutes) ...... . 152 License Plate Lamp .............................................
.152
BULB REPLACEMENT, REMOVAL AND
INSTALLATION ................................................ .152
Front Parking Lamp ............................................. .153
BULB REPLACEMENT .................................... .153
REMOVAL AND INSTALLATION ..................... .153
Tail Lamp ............................................................. .153
BULB REPLACEMENT .................................... .153
REMOVAL AND INSTALLATION ..................... .153
Front Side Marker Lamp ...................................... .153
BULB REPLACEMENT .................................... .153
REMOVAL AND INSTALLATION ..................... .153
Rear Side Marker Lamp ...................................... .153
BULB REPLACEMENT .................................... .153
REMOVAL AND INSTALLATION ..................... .153
Rear Combination Lamp Control Unit .................. .153
REMOVAL AND INSTALLATION ..................... .153
REAR COMBINATION LAMP ................................ .154
Bulb Replacement ............................................... .154
REAR FENDER SIDE (REAR SIDE MARKER
LAMP BULB) .................................................... .154
BACK DOOR SIDE (BACK-UP LAMP) ............ .154
Removal and Installation ..................................... .154
REMOVAL ........................................................ .154
INSTALLATION ................................................ .155
INTERIOR ROOM LAMP ....................................... .156
Component Parts and Harness Connector Location .156
System Description .............................................. .156
POWER SUPPLY AND GROUND ................... .157
SWITCH OPERATION ..................................... .158
ROOM LAMP TIMER OPERATION ................. .159
INTERIOR LAMP BATTERY SAVER CONTROL .160
Schematic ............................................................ .162
Wiring Diagram — ROOM/L — ........................... .164
Terminals and Reference Values for BCM ........... .172
How to Proceed With Trouble Diagnosis ............. .173
Preliminary Check ............................................... .173
CHECK FOR POWER SUPPLY AND GROUND
CIRCUIT ........................................................... .173
CONSULT-II Functions (BCM) ............................. .174
CONSULT-II BASIC OPERATION .................... .174
WORK SUPPORT (INT LAMP) ........................ .174
DATA MONITOR (INT LAMP) .......................... .174
ACTIVE TEST (INT LAMP) .............................. .175
WORK SUPPORT (BATTERY SAVER) ........... .176
DATA MONITOR (BATTERY SAVER) .............. .176
ACTIVE TEST (BATTERY SAVER) .................. .177
Interior Room Lamp Control Does Not Operate .. .177
Map Lamp Control Does Not Operate ................. .178
Personal Lamp Control Does Not Operate .......... .181
Ignition Key Hole Illumination Control Does Not
Operate ................................................................ .182
All Step Lamps Do Not Operate .......................... .184
All Interior Room Lamps Do Not Operate ............ .185
Bulb Replacement ............................................... .185
IGNITION KEY HOLE ILLUMINATION (WITH-
OUT INTELIGENT KEY) .................................. .185
IGNITION KEY HOLE ILLUMINATION (WITH
INTELIGENT KEY) ........................................... .185