bulb INFINITI FX35 2007 User Guide
[x] Cancel search | Manufacturer: INFINITI, Model Year: 2007, Model line: FX35, Model: INFINITI FX35 2007Pages: 4366, PDF Size: 55.42 MB
Page 3459 of 4366
LT-3
C
D E
F
G H
I
J
L
M A
B
LT
Revision: 2006 July 2007 FX35/FX45
LIGHTING AND TURN SIGNAL SWITCH .............
. 109
Removal and Installation ..................................... . 109
REMOVAL ........................................................ . 109
INSTALLATION ................................................ . 109
HAZARD SWITCH ................................................. ..110
Removal and Installation ..................................... .. 110
REMOVAL ........................................................ .. 110
INSTALLATION ................................................ .. 110
COMBINATION SWITCH ....................................... .. 111
Wiring Diagram — COMBSW — ......................... . . 111
Combination Switch Reading Function ............... .. 112
Terminals and Reference Values for BCM .......... .. 112
CONSULT-II Functions (BCM) ............................ .. 117
CONSULT-II BASIC OPERATION .................... .. 117
DATA MONITOR .............................................. .. 117
Combination Switch Inspection ........................... .. 118
Removal and Installation ..................................... . 120
STOP LAMP .......................................................... . 121
Component Parts and Harness Connector Location . 121
System Description ............................................. . 121
Schematic ........................................................... . 122
Wiring Diagram — STOP/L — ............................. . 123
Terminals and Reference Value for Rear Combina-
tion Lamp Control Unit ........................................ . 126
Stop Lamp Does Not Operate ............................. . 126
High-Mounted Stop Lamp ................................... . 128
BULB REPLACEMENT, REMOVAL AND
INSTALLATION ................................................ . 128
Stop Lamp ........................................................... . 128
BULB REPLACEMENT .................................... . 128
REMOVAL AND INSTALLATION ..................... . 128
Rear Combination Lamp Control Unit ................. . 128
REMOVAL AND INSTALLATION ..................... . 128
BACK-UP LAMP ................................................... . 129
Wiring Diagram — BACK/L — ............................ . 129
Bulb Replacement ............................................... . 130
Removal and Installation ..................................... . 130
PARKING, LICENSE PLATE AND TAIL LAMPS .. . 131
Component Parts and Harness Connector Location . 131
System Description ............................................. . 131
OUT LINE ......................................................... . 131
OPERATION BY LIGHTING SWITCH ............. . 132
COMBINATION SWITCH READING FUNCTION . 133
EXTERIOR LAMP BATTERY SAVER CONTROL . 133
CAN Communication System Description ........... . 133
CAN Communication Unit ................................... . 133
Schematic ........................................................... . 134
Wiring Diagram — TAIL/L — ............................... . 135
Terminals and Reference Values for BCM .......... . 140
Terminals and Reference Values for IPDM E/R .. . 141
Terminals and Reference Value for Rear Combina-
tion Lamp Control Unit ........................................ . 141
How to Proceed With Trouble Diagnosis ............. . 141
Preliminary Check ............................................... . 141
CHECK POWER SUPPLY AND GROUND CIR-
CUIT ................................................................. . 141
CONSULT-II Functions (BCM) ............................ . 142
CONSULT-II Functions (IPDM E/R) .................... . 142
Parking, License Plate and Side Marker Lamps Do Not Illuminate .......................................................
.143
Tail Lamp Does Not Operate ............................... .147
Parking, License Plate, Side Maker and Tail Lamps
Do Not Turn OFF (After Approx. 10 Minutes) ...... .149
License Plate Lamp ............................................. .150
BULB REPLACEMENT, REMOVAL AND
INSTALLATION ................................................ .150
Front Parking Lamp ............................................. .150
BULB REPLACEMENT .................................... .150
REMOVAL AND INSTALLATION ..................... .150
Tail Lamp ............................................................. .150
BULB REPLACEMENT .................................... .150
REMOVAL AND INSTALLATION ..................... .150
Front Side Marker Lamp ...................................... .150
BULB REPLACEMENT .................................... .150
REMOVAL AND INSTALLATION ..................... .150
Rear Side Marker Lamp ...................................... .150
BULB REPLACEMENT .................................... .150
REMOVAL AND INSTALLATION ..................... .150
Rear Combination Lamp Control Unit .................. .150
REMOVAL AND INSTALLATION ..................... .150
REAR COMBINATION LAMP ................................ .151
Bulb Replacement ............................................... .151
REAR FENDER SIDE (REAR SIDE MARKER
LAMP BULB) .................................................... .151
BACK DOOR SIDE (BACK-UP LAMP) ............ .151
Removal and Installation ..................................... .151
REMOVAL ........................................................ .151
INSTALLATION ................................................ .151
INTERIOR ROOM LAMP ....................................... .152
Component Parts and Harness Connector Location .152
System Description .............................................. .152
POWER SUPPLY AND GROUND ................... .153
SWITCH OPERATION ..................................... .154
ROOM LAMP TIMER OPERATION ................. .155
INTERIOR LAMP BATTERY SAVER CONTROL .157
Schematic ............................................................ .158
Wiring Diagram — ROOM/L — ........................... .160
Terminals and Reference Values for BCM ........... .168
How to Proceed With Trouble Diagnosis ............. .169
Preliminary Check ............................................... .170
CHECK FOR POWER SUPPLY AND GROUND
CIRCUIT ........................................................... .170
CONSULT-II Functions (BCM) ............................. .171
CONSULT-II BASIC OPERATION .................... .171
WORK SUPPORT (INT LAMP) ........................ .171
DATA MONITOR (INT LAMP) .......................... .171
ACTIVE TEST (INT LAMP) .............................. .172
WORK SUPPORT (BATTERY SAVER) ........... .173
DATA MONITOR (BATTERY SAVER) .............. .173
ACTIVE TEST (BATTERY SAVER) .................. .174
Interior Room Lamp Control Does Not Operate .. .174
Map Lamp Control Does Not Operate ................. .176
Personal Lamp Control Does Not Operate .......... .178
Ignition Key Hole Illumination Control Does Not
Operate ................................................................ .179
All Step Lamps Do Not Operate .......................... .181
All Interior Room Lamps Do Not Operate ............ .182
Bulb Replacement ............................................... .182
Page 3460 of 4366
LT-4Revision: 2006 July 2007 FX35/FX45
IGNITION KEY HOLE ILLUMINATION (WITH-
OUT INTELLIGENT KEY) ................................ .182
IGNITION KEY HOLE ILLUMINATION (WITH
INTELLIGENT KEY) ......................................... .182
FRONT STEP LAMP ........................................ .183
REAR STEP LAMP .......................................... .183
LUGGAGE ROOM LAMP ................................. .183
VANITY MIRROR LAMP .................................. .183
MAP LAMP ....................................................... .184
INTERIOR ROOM LAMP ................................. .184
PERSONAL LAMP ........................................... .184
Removal and Installation ..................................... .184
LUGGAGE ROOM LAMP ................................. .184
MAP LAMP ....................................................... .185
INTERIOR ROOM LAMP ................................. .185
PERSONAL LAMP ........................................... .185
ILLUMINATION ...................................................... .186
System Description .............................................. .186 ILLUMINATION OPERATION BY LIGHTING
SWITCH ............................................................ .186
EXTERIOR LAMP BATTERY SAVER CONTROL .187
CAN Communication System Description ........... .188
CAN Communication Unit .................................... .188
Schematic ............................................................ .189
Wiring Diagram — ILL — ..................................... .191
Bulb Replacement ................................................ .200
GLOVE BOX LAMP .......................................... .200
A/T DEVICE ILLUMINATION ............................ .200
COIN BOX ILLUMINATION .............................. .200
Removal and Installation ...................................... .200
ILLUMINATION CONTROL SWITCH ............... .200
BULB SPECIFICATIONS ....................................... .201
Headlamp ............................................................. .201
Exterior Lamp ....................................................... .201
Interior Lamp/Illumination ..................................... .201
Page 3461 of 4366
PRECAUTIONS LT-5
C
D E
F
G H
I
J
L
M A
B
LT
Revision: 2006 July 2007 FX35/FX45
PRECAUTIONS PFP:00011
Precautions for Supplemental Restraint System (SRS) “AIR BAG” and “SEAT
BELT PRE-TENSIONER”
NKS002V3
The Supplemental Restraint System such as “AIR BAG” and “SEAT BELT PRE-TENSIONER”, used along
with a front seat belt, helps to reduce the risk or severity of injury to the driver and front passenger for certain
types of collision. This system includes seat belt switch inputs and dual stage front air bag modules. The SRS
system uses the seat belt switches to determine the front air bag deployment, and may only deploy one front
air bag, depending on the severity of a collision and whether the front occupants are belted or unbelted.
Information necessary to service the system safely is included in the SRS and SB section of this Service Man-
ual.
WARNING:
To avoid rendering the SRS inoperative, which could increase the risk of personal injury or death
in the event of a collision which would result in air bag inflation, all maintenance must be per-
formed by an authorized NISSAN/INFINITI dealer.
Improper maintenance, including incorrect removal and installation of the SRS, can lead to per-
sonal injury caused by unintentional activation of the system. For removal of Spiral Cable and Air
Bag Module, see the SRS section.
Do not use electrical test equipment on any circuit related to the SRS unless instructed to in this
Service Manual. SRS wiring harnesses can be identified by yellow and/or orange harnesses or
harness connectors.
General Precautions for Service OperationsNKS002V4
Never work with wet hands.
Xenon headlamp includes high voltage generating part. Be sure
to disconnect battery negative cable (negative terminal) or
power fuse before removing, installing, or touching the xenon
headlamp (including lamp bulb).
Turn the lighting switch OFF before disconnecting and connect-
ing the connector.
When turning the xenon headlamp on and while it is illuminated,
never touch the harness, bulb, and socket of the headlamp.
When checking the headlamp on/off operation, check it on vehi-
cle and with the power connected to the vehicle-side connector.
Do not touch the headlamp bulb glass surface with bare hands or allow oil or grease to get on it. Do not
touch the headlamp bulb just after the headlamp is turned off, because it is very hot.
Install the xenon headlamp bulb socket correctly. If it is installed improperly, high-voltage leak or corona
discharge may occur that can melt the bulb, connector, and housing. Do not illuminate the xenon head-
lamp bulb out of the headlamp housing. Doing so can cause fire and harm your eyes.
When the bulb has burned out, wrap it in a thick vinyl bag and discard. Do not break the bulb.
Leaving the bulb removed from the headlamp housing for a long period of time can deteriorate the perfor-
mance of the lens and reflector (dirt, clouding). Always prepare a new bulb and have it on hand when
replacing the bulb.
When adjusting the headlamp aiming, turn the aiming adjustment screw only in the tightening direction. (If
it is necessary to loosen the screw, first fully loosen the screw, and then turn it in the tightening direction.)
Do not use organic solvent (paint thinner or gasoline) to clean lamps and to remove old sealant.
PKID0793E
Page 3462 of 4366
LT-6
HEADLAMP - XENON TYPE -
Revision: 2006 July 2007 FX35/FX45
HEADLAMP - XENON TYPE -PFP:26010
Component Parts and Harness Connector LocationNKS002V5
System DescriptionNKS002V6
Control of the headlamp system operation is dependent upon the position of the combination switch (lighting
switch). When the lighting switch is placed in the 2ND position, the BCM (body control module) receives input
signal requesting the headlamps (and tail lamps) illuminate. This input signal is communicated to the IPDM E/
R (intelligent power distribution module engine room) through the CAN communication lines. The CPU (central
processing unit) located in the IPDM E/R controls the headlamp high and headlamp low relay coils. These
relays, when energized, direct power to the respective headlamps, which then illuminate.
If voltage is applied to a high beam solenoid, the bulb shade will move, even a xenon head lamp bulb comes
out, and a high beam and a low beam are changed.
OUTLINE
Power is supplied at all times
to headlamp high relay, located in IPDM E/R
to headlamp low relay, located in IPDM E/R and
to ignition relay, located in IPDM E/R, from battery direct,
through 10A fuse (No. 71, located in IPDM E/R)
to CPU located in IPDM E/R,
through 15A fuse (No. 78, located in IPDM E/R)
to CPU located in IPDM E/R,
through 50A fusible link (letter M, located in fuse, fusible link and relay box)
to BCM terminal 55,
through 15A fuse [No. 22, located in fuse block (J/B)]
to BCM terminal 42,
through 10A fuse [No. 19, located in fuse block (J/B)]
to combination meter terminal 8.
PKIC9683E
Page 3464 of 4366
LT-8
HEADLAMP - XENON TYPE -
Revision: 2006 July 2007 FX35/FX45
Ground is supplied
to front combination lamp RH and LH terminals 7
through grounds E21, E50 and E51,
With power and ground supplied, the high beam headlamps illuminate.
If voltage is applied to a high beam solenoid, the bulb shade will move, even a xenon head lamp bulb comes
out, and a high beam and a low beam are changed.
The unified meter and A/C amp. that received the high beam request signal by BCM through the CAN commu-
nication makes a high beam indicator lamp turn on in combination meter.
COMBINATION SWITCH READING FUNCTION
Refer to BCS-3, "COMBINATION SWITCH READING FUNCTION" .
EXTERIOR LAMP BATTERY SAVER CONTROL
When the combination switch (lighting switch) is in the 2ND position (ON), and the ignition switch is turned
from ON or ACC to OFF, the battery saver control function is activated.
Under this condition, the headlamps remain illuminated for 5 minutes, then the headlamps are turned OFF.
Exterior lamp battery saver control mode can be changed by the function setting of CONSULT-II.
AUTO LIGHT OPERATION (IF EQUIPPED)
Refer to LT- 5 5 , "System Description" .
VEHICLE SECURITY SYSTEM
The vehicle security system will flash the high beams if the system is triggered. Refer to BL-180, "VEHICLE
SECURITY (THEFT WARNING) SYSTEM" .
XENON HEADLAMP
Xenon type lamps are used for to the low beam headlamps. Xenon bulbs do not use a filament. Instead, they
produce light when a high voltage current is passed between two tungsten electrodes through a mixture of
xenon (an inert gas) and certain other metal halides. In addition to strong lighting power, electronic control of
the power supply gives the headlamps stable quality and tone color.
Followings are some advantages of the xenon type headlamp.
The light produced by the headlamps is white color similar to sunlight that is easy to the eyes.
Light output is nearly double that of halogen headlamps, affording increased area of illumination.
Counter-reflected luminance increases and the contrast enhances on the wet road in the rain. That makes
visibility go up more than the increase of the light volume.
Power consumption is approximately 25 percent less than halogen headlamps, reducing battery load.
CAN Communication System DescriptionNKS002V7
CAN (Controller Area Network) is a serial communication line for real time application. It is an on-vehicle mul-
tiplex communication line with high data communication speed and excellent error detection ability. Many elec-
tronic control units are equipped onto a vehicle, and each control unit shares information and links with other
control units during operation (not independent). In CAN communication, control units are connected with 2
communication lines (CAN H line, CAN L line) allowing a high rate of information transmission with less wiring.
Each control unit transmits/receives data but selectively reads required data only.
CAN Communication UnitNKS002V8
Refer to LAN-49, "CAN System Specification Chart" .
Page 3483 of 4366
HEADLAMP - XENON TYPE - LT-27
C
D E
F
G H
I
J
L
M A
B
LT
Revision: 2006 July 2007 FX35/FX45
5. CHECK HEADLAMP CIRCUIT
1. Turn ignition switch OFF.
2. Disconnect IPDM E/R connector.
3. Check continuity between IPDM E/R harness connector E7 ter- minal 20 and front combination lamp RH harness connector E24
terminal 6.
4. Check continuity between IPDM E/R harness connector E7 ter- minal 30 and front combination lamp LH harness connector E44
terminal 6.
OK or NG
OK >> Replace IPDM E/R.
NG >> Repair harness or connector.
6. CHECK HEADLAMP GROUND
1. Turn ignition switch OFF.
2. Check continuity between front combination lamp RH harness connector E24 terminal 7 and ground.
3. Check continuity between front combination lamp LH harness connector E44 terminal 7 and ground.
OK or NG
OK >> Check headlamp harness and connectors, ballasts (HID control unit), and xenon bulbs. Refer to LT- 3 2 , "
Xenon Headlamp Trouble Diagnosis" .
NG >> Repair harness or connector.
Headlamp Low Beam Does Not Illuminate (One Side)NKS002VL
1. CHECK BULB
Check ballast (HID control unit) and xenon bulb of lamp which does not illuminate. Refer to LT- 3 2 , "
Xenon
Headlamp Trouble Diagnosis" .
OK or NG
OK >> GO TO 2.
NG >> Replace malfunctioning part. 20 – 6 : Continuity should exist.
30 – 6 : Continuity should exist.
PKIA5209E
7 – Ground : Continuity should exist.
7 – Ground : Continuity should exist.
PKIA5207E
Page 3485 of 4366
HEADLAMP - XENON TYPE - LT-29
C
D E
F
G H
I
J
L
M A
B
LT
Revision: 2006 July 2007 FX35/FX45
Headlamp RH Low Beam and High Beam Does Not Illuminate NKS002VM
1. CHECK BULB
Inspect ballast (HID control unit) and xenon bulb of lamp which does not illuminate. Refer to LT- 3 2 , "
Xenon
Headlamp Trouble Diagnosis" .
OK or NG
OK >> GO TO 2.
NG >> Replace malfunctioning part.
2. CHECK HEADLAMP GROUND
1. Turn ignition switch OFF.
2. Disconnect front combination lamp RH connector.
3. Check continuity between front combination lamp RH harness connector E24 terminal 7 and ground.
OK or NG
OK >> GO TO 3.
NG >> Repair harness or connector.
3. CHECK HEADLAMP CIRCUIT
1. Disconnect IPDM E/R connector.
2. Check continuity between IPDM E/R harness connector E7 ter- minal 27 and front combination lamp RH harness connector E24
terminal 5.
3. Check continuity between IPDM E/R harness connector E7 ter- minal 20 and front combination lamp RH harness connector E24
terminal 6.
OK or NG
OK >> Replace IPDM E/R.
NG >> Repair harness or connector.
Headlamp LH Low Beam and High Beam Does Not Illuminate NKS002VN
1. CHECK BULB
Inspect ballast (HID control unit) and xenon bulb of lamp which does not illuminate. Refer to LT- 3 2 , "
Xenon
Headlamp Trouble Diagnosis" .
OK or NG
OK >> GO TO 2.
NG >> Replace malfunctioning part. 7 – Ground : Continuity should exist.
PKIA5207E
27 – 5 : Continuity should exist.
PKIA7587E
20 – 6 : Continuity should exist.
PKIA5211E
Page 3488 of 4366
LT-32
HEADLAMP - XENON TYPE -
Revision: 2006 July 2007 FX35/FX45
General Information for Xenon Headlamp Trouble DiagnosisNKS002VP
In most cases, malfunction of xenon headlamp - “does not illuminate”, “flickers” or “dark” - is caused by a mal-
functioning xenon bulb. A malfunctioning HID control unit or lamp housing, however, may be a cause. Be sure
to perform trouble diagnosis following the steps described below.
Caution:NKS002VQ
Installation or removal of connector must be done with lighting switch OFF.
Disconnect the battery cable from the negative terminal or remove power fuse.
When the lamp is illuminated (when lighting switch is ON), never touch harness, HID control unit, inside of
lamp, or lamp metal parts.
To check illumination, temporarily install lamp in vehicle. Be sure to connect power at vehicle side connec-
tor.
If error can be traced directly to electrical system, first check for items such as blown fuses and fusible
links, broken wires or loose connectors, dislocated terminals, and improper connections.
Never work with wet hands.
Using a tester for HID control unit circuit trouble diagnosis is prohibited.
Disassembling HID control unit or harnesses (bulb socket harness, ECM harness) is prohibited.
Immediately after illumination, light intensity and color will fluctuate, but there is nothing wrong.
When bulb has come to end of its life, brightness will drop significantly, it will flash repeatedly, or light color
will turn reddish.
Xenon Headlamp Trouble DiagnosisNKS002VR
1. CHECK 1: XENON HEADLAMP LIGHTING
Install normal xenon bulb to corresponding xenon bulb headlamp, and check if lamp lights up.
OK or NG
OK >> Replace xenon bulb.
NG >> GO TO 2.
2. CHECK 2: XENON HEADLAMP LIGHTING
Install normal HID control unit to corresponding xenon headlamp, and check if lamp lights up.
OK or NG
OK >> Replace HID control unit.
NG >> GO TO 3.
3. CHECK 3: XENON HEADLAMP LIGHTING
Install normal xenon lamp housing assembly to corresponding xenon headlamp, and check if lamp lights up.
OK or NG
OK >> Replace xenon headlamp housing assembly. [Malfunction in starter (boosting circuit) in xenon headlamp housing]
NG >> INSPECTION END
Page 3490 of 4366
LT-34
HEADLAMP - XENON TYPE -
Revision: 2006 July 2007 FX35/FX45
ADJUSTMENT USING AN ADJUSTMENT SCREEN (LIGHT/DARK BORDERLINE)
If the vehicle front body has been repaired and/or headlamp assembly has been replaced, check aiming.
Use the aiming chart shown in the figure.
Basic illumination area for adjustment should be within the range shown on the aiming chart.
Adjust headlamp accordingly.
Bulb ReplacementNKS002VT
HEADLAMP HIGH/LOW BEAM
1. Turn lighting switch OFF.
2. Disconnect the battery cable from the negative terminal or remove power fuse.
3. Remove air cleaner case (when replacing LH bulb). Refer to EM-177, "
AIR CLEANER AND AIR DUCT" (VK45) or refer to
EM-17, "
AIR CLEANER AND AIR DUCT" (VQ35).
4. Remove radiator reservoir tank (when replacing RH bulb). Refer to CO-41, "
RADIATOR" (VK45) or refer to CO-14, "RADIATOR"
(VQ35).
5. Turn plastic cap counterclockwise and unlock it.
6. Turn bulb socket counterclockwise and unlock it.
7. Unlock retaining spring and remove bulb from headlamp.
8. Installation is the reverse order of removal.
NOTE:
After installation, perform aiming adjustment. Refer to LT- 3 3 , "
Aiming Adjustment" .
PKIC9731E
Headlamp high/low beam (Xenon) : 12 V - 35 W (D2S)
PKIC9730E
Page 3491 of 4366
HEADLAMP - XENON TYPE - LT-35
C
D E
F
G H
I
J
L
M A
B
LT
Revision: 2006 July 2007 FX35/FX45
DAYTIME/PARKING LAMP
1. Turn lighting switch OFF.
2. Remove air cleaner case (when replacing LH bulb of VK45). Refer to EM-177, "
AIR CLEANER AND AIR DUCT" .
3. Turn bulb socket counterclockwise and unlock it.
4. Remove bulb from its socket.
5. Installation is the reverse order of removal.
FRONT TURN SIGNAL LAMP
1. Turn lighting switch OFF.
2. Turn bulb socket counterclockwise with suitable tool and unlock it.
3. Remove bulb from its socket.
4. Installation is the reverse order of removal.
FRONT SIDE MARKER LAMP
1. Turn lighting switch OFF.
2. Turn bulb socket counterclockwise and unlock it.
3. Remove bulb from its socket.
4. Installation is the reverse order of removal.
CAUTION:
After installing bulb, be sure to install plastic cap and bulb socket securely to insure watertight-
ness.
Removal and InstallationNKS002VU
REMOVAL
1. Disconnect the battery cable from the negative terminal or remove power fuse.
2. Remove front bumper facia asembly. Refer to EI-14, "
Removal
and Installation" .
3. Remove headlamp mounting bolts and nut.
4. Remove plastics bumper bracket, then pull headlamp toward vehicle front, disconnect connector, and remove headlamp. Daytime/Parking lamp : 12 V - 21/5 W
PKIC9732E
Front turn signal lamp : 12 V - 21 W (amber)
SKIA6182E
Front side marker lamp : 12 V - 3.8 W
SKIA5552E
SKIA5553E