oil level INFINITI FX35 2008 Service Manual

ACS-14
< SERVICE INFORMATION >[ICC]
LASER BEAM AIMING ADJUSTMENT
LASER BEAM AIMING ADJUSTMENT
OutlineINFOID:0000000001328812
Adjust the laser beam aiming every time the ICC sensor is removed or installed.
CAUTION:
 Adjust laser beam aiming at a horizontal place as
far as 12 m (39 ft) forward the vehicle can be seen.
 Adjust laser beam aiming 5 seconds after starting engine.
 Never view ICC sensor integrated un it body window directly during laser beam aiming adjustment.
 Follow the CONSULT-III when adju sting the laser beam aiming (laser beam aiming adjustment can-
not be operated without CONSULT-III).
 Never ride on vehicle during l aser beam aiming adjustment.
 Idle and turn headlamps OFF duri ng laser beam aiming adjustment.
PreparationINFOID:0000000001328813
 Adjust the tire pressure to the specified value.
 See that there is no load in the vehicle.
 Coolant, engine oil filled up to correct level and full fuel tank.
 Shift the gear into “P” position and release the parking brake.
 Clean the ICC sensor with a soft cloth.
Outline of Adjustment ProcedureINFOID:0000000001328814
1. Set up the ICC target board [KV99110100 (J-45718)].
2. Adjust the sensor following the procedure on CONSUL T-III. (Turn manually the screw for up-down position
adjustment. ICC sensor automatically adjust the right-left position.)
Setting the ICC Target BoardINFOID:0000000001328815
Accurate ICC target board setting is required for the laser beam aiming adjustment.
CAUTION:
ICC system does not function normally if laser beam aiming is not accurate.
ADJUSTING HEIGHT OF THE TARGET
1. Attach a triangle scale at the center.
SKIA6179E
SKIA5974E
3AA93ABC3ACD3AC03ACA3AC03AC63AC53A913A773A893A873A873A8E3A773A983AC73AC93AC03AC3
3A893A873A873A8F3A773A9D3AAF3A8A3A8C3A863A9D3AAF3A8B3A8C

A/T FLUIDAT-13
< SERVICE INFORMATION >
DE
F
G H
I
J
K L
M A
B
AT
N
O P
9. Install the removed A/T fluid level gauge in the A/T fluid charging pipe.
10. Tighten level gauge bolt.
A/T Fluid Cooler CleaningINFOID:0000000001327130
Whenever an A/T is replaced, the A/ T fluid cooler mounted in the radiator must be inspected and cleaned.
Metal debris and friction material, if present, can becom e trapped in the A/T fluid cooler. This debris can con-
taminate the newly serviced A/T or, in severe cases, can bl ock or restrict the flow of ATF. In either case, mal-
function of the newly se rviced A/T may result.
Debris, if present, may build up as ATF enters the cooler inlet. It will be necessary to back flush the cooler
through the cooler outlet in order to flush out any built up debris.
A/T FLUID COOLER CLEANING PROCEDURE
1. Position an oil pan under the A/T's inlet and outlet cooler hoses.
2. Identify the inlet and outlet A/T fluid cooler hoses.
3. Disconnect the A/T fluid cooler inlet and outlet rubber hoses from the steel cooler tubes or bypass valve.
NOTE:
Replace the cooler hoses if rubber material from the hose
remains on the tube fitting.
4. Allow any ATF that remains in the cooler hoses to drain into the oil pan.
5. Insert the extension adapter hose of a can of Transmission Cooler Cleaner (Nissan P/N 999MP-AM006) into the cooler out-
let hose.
CAUTION:
 Wear safety glasses and rubber gloves when spraying theTransmission Cooler Cleaner.
 Spray Transmission Cooler Cleaner only with adequate
ventilation.
 Avoid contact with eyes and skin.
 Do not breath vapors or spray mist.
6. Hold the hose and can as high as possible and spray Transmis- sion Cooler Cleaner in a continuous stream into the cooler outlet
hose until ATF flows out of the cooler inlet hose for 5 seconds.Level gauge bolt:
: 5.1 N·m (0.52 kg-m, 45 in-lb)
SCIA4896E
SCIA3830E
SCIA3831E
3AA93ABC3ACD3AC03ACA3AC03AC63AC53A913A773A893A873A873A8E3A773A983AC73AC93AC03AC3
3A893A873A873A8F3A773A9D3AAF3A8A3A8C3A863A9D3AAF3A8B3A8C

TROUBLE DIAGNOSISAT-53
< SERVICE INFORMATION >
DE
F
G H
I
J
K L
M A
B
AT
N
O P
Road TestINFOID:0000000001425855
DESCRIPTION
 The road test checks overall performance of the A/T and analyzes possible malfunction causes.
 The road test is carried out in the following three stages.
1. Check before engine is started.
2. Check at idle.
3. Cruise test
 Inspect all the items Part 1 to Part 3.
 Before beginning the road test, che ck the procedure and inspection items.
 Test all inspection items until the symptom is uncov ered. Diagnose NG items when all road tests are com-
plete.
CHECK BEFORE ENGINE IS STARTED
1.CHECK A/T CHECK INDICATOR LAMP
1. Park vehicle on level surface.
2. Move selector lever to “P” position.
3. Turn ignition switch OFF and wait at least 10 seconds.
4. Turn ignition switch ON.
Does A/T CHECK indicator lamp light up for about 2 seconds?
YES - 1>> With CONSULT-III
1. Perform self-diagnostics and record all NG items on the “Diagnostic Worksheet Chart”.
2. Go to “CHECK AT IDLE”.
YES - 2>> Without CONSULT-III
1. Perform self-diagnostics and record all NG it ems on the “Diagnostic Worksheet Chart”. Refer
to AT-91, "
Diagnosis Procedure without CONSULT-III".
2. Go to “CHECK AT IDLE”.
NO >> Stop the road test and go to AT-170, "
A/T Check Indicator Lamp Does Not Come On".
CHECK AT IDLE
1.CHECK STARTING THE ENGINE
1. Park vehicle on level surface.
2. Move selector lever to “P” or “N” position.
3. Turn ignition switch OFF.
4. Start engine.
Does the engine start?
YES >> GO TO 2.
NO >> Stop the road test and go to AT-170, "
Engine Cannot Be Started in "P" or "N" Position".
Stall speedLine pressure does
not rise higher than
the line pressure for
idle.
Possible causes include a sensor malfunction or malfunction in the pressure adjustment function.
For example
 Accelerator pedal position signal malfunction
 TCM breakdown
 Line pressure solenoid malfunction (shorting, sticking in ON state)
 Pressure regulator valve or plug sticking
 Pilot valve sticking or pilot filter clogged
The pressure rises,
but does not enter
the standard posi-
tion. Possible causes include malfunctions in the pressure supply system and malfunction in the pres-
sure adjustment function.
For example
 Accelerator pedal position signal malfunction
 Line pressure solenoid malfunction (sticking, filter clog)
 Pressure regulator valve or plug sticking
 Pilot valve sticking or pilot filter clogged
Only low for a spe-
cific position Possible causes include an oil pressure leak in a passage or device related to the position after
the pressure is distributed by the manual valve.
Judgement Possible cause
3AA93ABC3ACD3AC03ACA3AC03AC63AC53A913A773A893A873A873A8E3A773A983AC73AC93AC03AC3
3A893A873A873A8F3A773A9D3AAF3A8A3A8C3A863A9D3AAF3A8B3A8C

TROUBLE DIAGNOSISAT-67
< SERVICE INFORMATION >
DE
F
G H
I
J
K L
M A
B
AT
N
O P
23
Slips/Will
Not En-
gage Vehicle cannot be
started from D
1.
Refer to AT- 1 8 0 , "
Ve-
hicle Cannot Be Start-
ed from D1". ON vehicle
1. A/T fluid level and state
AT- 4 9
2. Accelerator pedal position sensorAT- 1 3 0
3. Line pressure test AT- 4 9
4. CAN communication lineAT- 9 4
5. Control valve with TCMAT- 2 1 5
OFF vehicle6. Torque converter
AT- 2 6 7
7. Oil pump assemblyAT- 2 8 5
8. 3rd one-way clutchAT- 2 8 7
9. 1st one-way clutch AT- 2 9 5
10. Gear systemAT- 2 4 9
11. Reverse brakeAT- 2 6 7
12. Forward one-way clutch (Parts behind drum support is im-
possible to perform inspection by disassembly. Refer to AT-
16, "Cross-Sectional View (2WD Models)", AT- 1 7 , "Cross-
Sectional View (VQ35DE Models for AWD)" or AT- 1 8 , "Cross-
Sectional View (VK45DE Models for AWD)") AT- 2 6 7
13. Forward brake (Parts behind drum support is impossible
to perform inspection by disassembly. Refer to
AT- 1 6 , "
Cross-
Sectional View (2WD Models)", AT- 1 7 , "Cross-Sectional View
(VQ35DE Models for AWD)" or AT- 1 8 , "Cross-Sectional View
(VK45DE Models for AWD)") AT- 2 6 7
24
Does not lock-up.
Refer to
AT- 1 9 0 , "A/T
Does Not Lock-up".ON vehicle 1. A/T fluid level and state
AT- 4 9
2. Line pressure testAT- 4 9
3. Engine speed signalAT- 11 2
4. Turbine revolution sensorAT- 1 0 6
5. Torque converter clutch solenoid valveAT- 1 2 4
6. CAN communication line AT- 9 4
7. Control valve with TCMAT- 2 1 5
OFF vehicle8. Torque converter
AT- 2 6 79. Oil pump assemblyAT- 2 8 5
25Does not hold lock-up
condition.
Refer to
AT- 1 9 2 , "A/T
Does Not Hold Lock-
up Condition". ON vehicle 1. A/T fluid level and state
AT- 4 9
2. Line pressure testAT- 4 9
3. Engine speed signalAT- 11 2
4. Turbine revolution sensorAT- 1 0 6
5. Torque converter clutch solenoid valveAT- 1 2 4
6. CAN communication line AT- 9 4
7. Control valve with TCMAT- 2 1 5
OFF vehicle8. Torque converter
AT- 2 6 79. Oil pump assemblyAT- 2 8 5
No. Items Symptom Condition Diagnostic Item Reference
page
3AA93ABC3ACD3AC03ACA3AC03AC63AC53A913A773A893A873A873A8E3A773A983AC73AC93AC03AC3
3A893A873A873A8F3A773A9D3AAF3A8A3A8C3A863A9D3AAF3A8B3A8C

AT-68
< SERVICE INFORMATION >
TROUBLE DIAGNOSIS
26Slips/Will
Not En-
gage Lock-up is not re-
leased.
Refer to
AT- 1 9 4 ,
"Lock-up Is Not Re-
leased". ON vehicle1. A/T fluid level and state
AT- 4 9
2. Line pressure testAT- 4 9
3. Engine speed signalAT- 11 2
4. Turbine revolution sensorAT- 1 0 6
5. Torque converter clutch solenoid valveAT- 1 2 4
6. CAN communication line AT- 9 4
7. Control valve with TCMAT- 2 1 5
OFF vehicle8. Torque converter
AT- 2 6 79. Oil pump assemblyAT- 2 8 5
27No shock at all or the
clutch slips when vehi-
cle changes speed D1
→ D
2 or M1 → M2. ON vehicle
1. A/T fluid level and state
AT- 4 9
2. Vehicle speed sensor A/T and vehicle speed sensor MTRAT- 1 0 8,
AT- 1 3 7
3. Direct clutch solenoid valve AT- 1 4 7
4. CAN communication line AT- 9 4
5. Line pressure testAT- 4 9
6. Control valve with TCMAT- 2 1 5
OFF vehicle7. Torque converter
AT- 2 6 7
8. Oil pump assemblyAT- 2 8 5
9. 3rd one-way clutchAT- 2 8 7
10. Gear systemAT- 2 4 9
11. Direct clutchAT- 3 0 3
12. Forward brake (Parts behind drum support is impossible
to perform inspection by disassembly. Refer to AT- 1 6 , "
Cross-
Sectional View (2WD Models)", AT- 1 7 , "Cross-Sectional View
(VQ35DE Models for AWD)" or AT- 1 8 , "Cross-Sectional View
(VK45DE Models for AWD)") AT- 2 6 7
No. Items Symptom Condition Diagnostic Item
Reference
page
3AA93ABC3ACD3AC03ACA3AC03AC63AC53A913A773A893A873A873A8E3A773A983AC73AC93AC03AC3
3A893A873A873A8F3A773A9D3AAF3A8A3A8C3A863A9D3AAF3A8B3A8C

TROUBLE DIAGNOSISAT-69
< SERVICE INFORMATION >
DE
F
G H
I
J
K L
M A
B
AT
N
O P
28
Slips/Will
Not En-
gage No shock at all or the
clutch slips when vehi-
cle changes speed D2
→ D
3 or M2 → M3. ON vehicle
1. A/T fluid level and state
AT- 4 9
2. Vehicle speed sensor A/T and vehicle speed sensor MTRAT- 1 0 8,
AT- 1 3 7
3. High and low reverse clutch solenoid valve AT- 1 4 9
4. CAN communication line AT- 9 4
5. Line pressure testAT- 4 9
6. Control valve with TCMAT- 2 1 5
OFF vehicle7. Torque converter
AT- 2 6 7
8. Oil pump assemblyAT- 2 8 5
9. 3rd one-way clutchAT- 2 8 7
10. Gear systemAT- 2 4 9
11. High and low reverse clutchAT- 3 0 1
12. Forward one-way clutch (Parts behind drum support is im-
possible to perform inspection by disassembly. Refer to AT-
16, "Cross-Sectional View (2WD Models)", AT- 1 7 , "Cross-
Sectional View (VQ35DE Models for AWD)" or AT- 1 8 , "Cross-
Sectional View (VK45DE Models for AWD)") AT- 2 6 7
13. Forward brake (Parts behind drum support is impossible
to perform inspection by disassembly. Refer to
AT- 1 6 , "
Cross-
Sectional View (2WD Models)", AT- 1 7 , "Cross-Sectional View
(VQ35DE Models for AWD)" or AT- 1 8 , "Cross-Sectional View
(VK45DE Models for AWD)") AT- 2 6 7
29
No shock at all or the
clutch slips when vehi-
cle changes speed D3
→ D
4 or M3 → M4. ON vehicle
1. A/T fluid level and state
AT- 4 9
2. Vehicle speed sensor A/T and vehicle speed sensor MTRAT- 1 0 8,
AT- 1 3 7
3.Input clutch solenoid valve AT- 1 4 3
4. Front brake solenoid valve AT- 1 4 5
5. CAN communication line AT- 9 4
6. Line pressure testAT- 4 9
7. Control valve with TCMAT- 2 1 5
OFF vehicle8. Torque converter
AT- 2 6 7
9. Oil pump assemblyAT- 2 8 5
10. Input clutchAT- 2 8 9
11. Gear systemAT- 2 4 9
12. High and low reverse clutchAT- 3 0 1
13. Direct clutchAT- 3 0 3
No. Items Symptom Condition Diagnostic Item Reference
page
3AA93ABC3ACD3AC03ACA3AC03AC63AC53A913A773A893A873A873A8E3A773A983AC73AC93AC03AC3
3A893A873A873A8F3A773A9D3AAF3A8A3A8C3A863A9D3AAF3A8B3A8C

AT-70
< SERVICE INFORMATION >
TROUBLE DIAGNOSIS
30Slips/Will
Not En-
gage No shock at all or the
clutch slips when vehi-
cle changes speed D4
→ D
5 or M4 → M5. ON vehicle
1. A/T fluid level and state
AT- 4 9
2. Vehicle speed sensor A/T and vehicle speed sensor MTRAT- 1 0 8,
AT- 1 3 7
3. Front brake solenoid valve AT- 1 4 5
4. Direct clutch solenoid valveAT- 1 4 7
5. CAN communication line AT- 9 4
6. Line pressure testAT- 4 9
7. Control valve with TCMAT- 2 1 5
OFF vehicle8. Torque converter
AT- 2 6 7
9. Oil pump assemblyAT- 2 8 5
10. Front brake (brake band)AT- 2 6 7
11. Input clutchAT- 2 8 9
12. Gear systemAT- 2 4 9
13. High and low reverse clutchAT- 3 0 1
31When you press the
accelerator pedal and
shift speed D5
→ D4 or
M5 → M4 the engine
idles or the A/T slips. ON vehicle
1. A/T fluid level and state
AT- 4 9
2. Vehicle speed sensor A/T and vehicle speed sensor MTRAT- 1 0 8,
AT- 1 3 7
3. Front brake solenoid valve AT- 1 4 5
4. Direct clutch solenoid valveAT- 1 4 7
5. CAN communication line AT- 9 4
6. Line pressure testAT- 4 9
7. Control valve with TCMAT- 2 1 5
OFF vehicle8. Torque converter
AT- 2 6 7
9. Oil pump assemblyAT- 2 8 5
10. Input clutchAT- 2 8 9
11. Gear systemAT- 2 4 9
12. High and low reverse clutchAT- 3 0 1
13. Direct clutchAT- 3 0 3
No. Items Symptom Condition Diagnostic Item Reference
page
3AA93ABC3ACD3AC03ACA3AC03AC63AC53A913A773A893A873A873A8E3A773A983AC73AC93AC03AC3
3A893A873A873A8F3A773A9D3AAF3A8A3A8C3A863A9D3AAF3A8B3A8C

TROUBLE DIAGNOSISAT-71
< SERVICE INFORMATION >
DE
F
G H
I
J
K L
M A
B
AT
N
O P
32
Slips/Will
Not En-
gage When pressing the ac-
celerator pedal and
shifting speed D4
→
D
3 or M4 → M3 the en-
gine idles or the A/T
slips. ON vehicle
1. A/T fluid level and state
AT- 4 9
2. Vehicle speed sensor A/T and vehicle speed sensor MTRAT- 1 0 8,
AT- 1 3 7
3. Input clutch solenoid valve AT- 1 4 3
4. Front brake solenoid valveAT- 1 4 5
5. CAN communication line AT- 9 4
6. Line pressure testAT- 4 9
7. Control valve with TCMAT- 2 1 5
OFF vehicle8. Torque converter
AT- 2 6 7
9. Oil pump assemblyAT- 2 8 5
10. 3rd one-way clutchAT- 2 8 7
11. Gear systemAT- 2 4 9
12. High and low reverse clutchAT- 3 0 1
13. Forward one-way clutch (Parts behind drum support is im-
possible to perform inspection by disassembly. Refer to AT-
16, "Cross-Sectional View (2WD Models)", AT- 1 7 , "Cross-
Sectional View (VQ35DE Models for AWD)" or AT- 1 8 , "Cross-
Sectional View (VK45DE Models for AWD)") AT- 2 6 7
14. Forward brake (Parts behind drum support is impossible
to perform inspection by disassembly. Refer to
AT- 1 6 , "
Cross-
Sectional View (2WD Models)", AT- 1 7 , "Cross-Sectional View
(VQ35DE Models for AWD)" or AT- 1 8 , "Cross-Sectional View
(VK45DE Models for AWD)") AT- 2 6 7
33When pressing the ac-
celerator pedal and
shifting speed D3
→
D
2 or M3 → M2 the en-
gine idles or the A/T
slips. ON vehicle
1. A/T fluid level and state
AT- 4 9
2. Vehicle speed sensor A/T and vehicle speed sensor MTRAT- 1 0 8,
AT- 1 3 7
3. High and low reverse clutch solenoid valve AT- 1 4 9
4.Direct clutch solenoid valveAT- 1 4 7
5. CAN communication line AT- 9 4
6. Line pressure testAT- 4 9
7. Control valve with TCMAT- 2 1 5
OFF vehicle8. Torque converter
AT- 2 6 7
9. Oil pump assemblyAT- 2 8 5
10. 3rd one-way clutch AT- 2 8 7
11. Gear systemAT- 2 4 9
12. Direct clutchAT- 3 0 3
13. Forward brake (Parts behind drum support is impossible
to perform inspection by disassembly. Refer to AT- 1 6 , "
Cross-
Sectional View (2WD Models)", AT- 1 7 , "Cross-Sectional View
(VQ35DE Models for AWD)" or AT- 1 8 , "Cross-Sectional View
(VK45DE Models for AWD)") AT- 2 6 7
No. Items Symptom Condition Diagnostic Item
Reference
page
3AA93ABC3ACD3AC03ACA3AC03AC63AC53A913A773A893A873A873A8E3A773A983AC73AC93AC03AC3
3A893A873A873A8F3A773A9D3AAF3A8A3A8C3A863A9D3AAF3A8B3A8C

AT-72
< SERVICE INFORMATION >
TROUBLE DIAGNOSIS
34Slips/Will
Not En-
gage When pressing the ac-
celerator pedal and
shifting speed D2
→
D
1 or M2 → M1 the
engine idles or the A/T
slips. ON vehicle
1. A/T fluid level and state
AT- 4 9
2. Vehicle speed sensor A/T and vehicle speed sensor MTRAT- 1 0 8,
AT- 1 3 7
3. Direct clutch solenoid valve AT- 1 4 7
4. CAN communication line AT- 9 4
5. Line pressure testAT- 4 9
6. Control valve with TCMAT- 2 1 5
OFF vehicle7. Torque converter
AT- 2 6 7
8. Oil pump assemblyAT- 2 8 5
9. 3rd one-way clutchAT- 2 8 7
10. 1st one-way clutchAT- 2 9 5
11. Gear systemAT- 2 4 9
12. Reverse brakeAT- 2 6 7
13. Forward one-way clutch (Parts behind drum support is im-
possible to perform inspection by disassembly. Refer to AT-
16, "Cross-Sectional View (2WD Models)", AT- 1 7 , "Cross-
Sectional View (VQ35DE Models for AWD)" or AT- 1 8 , "Cross-
Sectional View (VK45DE Models for AWD)") AT- 2 6 7
14. Forward brake (Parts behind drum support is impossible
to perform inspection by disassembly. Refer to
AT- 1 6 , "
Cross-
Sectional View (2WD Models)", AT- 1 7 , "Cross-Sectional View
(VQ35DE Models for AWD)" or AT- 1 8 , "Cross-Sectional View
(VK45DE Models for AWD)") AT- 2 6 7
35
With selector lever in
“D” position, accelera-
tion is extremely poor. ON vehicle
1. A/T fluid level and state
AT- 4 9
2. Line pressure testAT- 4 9
3. Accelerator pedal position sensorAT- 1 3 0
4. CAN communication line AT- 9 4
5. PNP switchAT- 1 0 2
6. A/T positionAT- 2 0 7
7. Control valve with TCMAT- 2 1 5
OFF vehicle8. Torque converter
AT- 2 6 7
9. Oil pump assemblyAT- 2 8 5
10. 1st one-way clutchAT- 2 9 5
11. Gear systemAT- 2 4 9
12. Reverse brakeAT- 2 6 7
13. Forward one-way clutch (Parts behind drum support is im-
possible to perform inspection by disassembly. Refer to AT-
16, "Cross-Sectional View (2WD Models)", AT- 1 7 , "Cross-
Sectional View (VQ35DE Models for AWD)" or AT- 1 8 , "Cross-
Sectional View (VK45DE Models for AWD)") AT- 2 6 7
14. Forward brake (Parts behind drum support is impossible
to perform inspection by disassembly. Refer to
AT- 1 6 , "
Cross-
Sectional View (2WD Models)", AT- 1 7 , "Cross-Sectional View
(VQ35DE Models for AWD)" or AT- 1 8 , "Cross-Sectional View
(VK45DE Models for AWD)") AT- 2 6 7
No. Items Symptom Condition Diagnostic Item
Reference
page
3AA93ABC3ACD3AC03ACA3AC03AC63AC53A913A773A893A873A873A8E3A773A983AC73AC93AC03AC3
3A893A873A873A8F3A773A9D3AAF3A8A3A8C3A863A9D3AAF3A8B3A8C

TROUBLE DIAGNOSISAT-73
< SERVICE INFORMATION >
DE
F
G H
I
J
K L
M A
B
AT
N
O P
36
Slips/Will
Not En-
gage With selector lever in
“R” position
, accelera-
tion is extremely poor. ON vehicle1. A/T fluid level and state
AT- 4 9
2. Line pressure testAT- 4 9
3. Accelerator pedal position sensorAT- 1 3 0
4. High and low reverse clutch solenoid valveAT- 1 4 9
5. CAN communication line AT- 9 4
6. PNP switchAT- 1 0 2
7. A/T positionAT- 2 0 7
8. Control valve with TCMAT- 2 1 5
OFF vehicle9. Gear system
AT- 2 4 910. Output shaft AT- 2 6 7
11. Reverse brakeAT- 2 6 7
37While starting off by
accelerating in 1st, en-
gine races or slippage
occurs. ON vehicle
1. A/T fluid level and state
AT- 4 9
2. Line pressure testAT- 4 9
3. Accelerator pedal position sensorAT- 1 3 0
4. CAN communication line AT- 9 4
5. Control valve with TCMAT- 2 1 5
OFF vehicle6. Torque converter
AT- 2 6 7
7. Oil pump assemblyAT- 2 8 5
8. 3rd one-way clutchAT- 2 8 7
9. 1st one-way clutchAT- 2 9 5
10. Gear systemAT- 2 4 9
11. Reverse brakeAT- 2 6 7
12. Forward one-way clutch (Parts behind drum support is im-
possible to perform inspection by disassembly. Refer to AT-
16, "Cross-Sectional View (2WD Models)", AT- 1 7 , "Cross-
Sectional View (VQ35DE Models for AWD)" or AT- 1 8 , "Cross-
Sectional View (VK45DE Models for AWD)") AT- 2 6 7
13. Forward brake (Parts behind drum support is impossible
to perform inspection by disassembly. Refer to
AT- 1 6 , "
Cross-
Sectional View (2WD Models)", AT- 1 7 , "Cross-Sectional View
(VQ35DE Models for AWD)" or AT- 1 8 , "Cross-Sectional View
(VK45DE Models for AWD)") AT- 2 6 7
No. Items Symptom Condition Diagnostic Item
Reference
page
3AA93ABC3ACD3AC03ACA3AC03AC63AC53A913A773A893A873A873A8E3A773A983AC73AC93AC03AC3
3A893A873A873A8F3A773A9D3AAF3A8A3A8C3A863A9D3AAF3A8B3A8C