lock INFINITI G37 2010 User Guide

Adjustment Adjust the head restraint so the center is level
with the center of your ears. To raise the head restraint, pull it up. To lower, push and hold the lock knob and push
the head restraint down.SSS0997 SSS0993 SSS0994
1-10 Safety — Seats, seat belts and supplemental restraint system
 —
—
10/12/09—tbrooks


Removal Use the following procedure to remove the
adjustable head restraints.
1. Pull the head restraint up to the highest
position.
2. Push and hold the lock knob.
3. Remove the head restraint from the seat.
4. Store the head restraint properly in a
secure place so it is not loose in the
vehicle.
Reinstall and properly adjust the head restraint
before an occupant uses the seating position. Install 1. Align the head restraint stalks with the
holes in the seat. Make sure that the head
restraint is facing the correct direction.
The stalk with the adjustment notches
 1
must be installed in the hole with the lock
knob
 2
.
2. Push and hold the lock knob and push the
head restraint down.
3. Properly adjust the head restraint before
an occupant uses the seating position. Front-seat Active Head Restraints The Active Head Restraint moves forward utiliz-
ing the force that the seatback receives from
the occupant in a rear-end collision. The move-
ment of the head restraint helps support the
occupant’s head by reducing its backward
movement and helping absorb some of the
forces that may lead to whiplash-type injuries.
Active Head Restraints are effective for colli-
sions at low to medium speeds in which it is
said that whiplash-type injury occurs most.
Active Head Restraints operate only in certain
rear-end collisions. After the collision, the head
restraints return to their original positions.
Adjust the Active Head Restraints properly as
described earlier in this section.SSS0995 SSS0996 SSS0508
Safety — Seats, seat belts and supplemental restraint system
1-11
 —
—
10/12/09—tbrooks


ARMREST (if so equipped)
Rear armrest Pull the armrest forward until it is horizontal.
Trunk pass-through The rear center seatback can be folded to allow
trunk access from inside of the vehicle.
To access the trunk, pull down the rear center
armrest and pull out the trunk pass-through lid
 1
.
To lock the lid, use the mechanical key and turn
it to the LOCK position
 3
. To unlock, turn the
mechanical key to the UNLOCK position
 2
. For
the mechanical key usage, see “KEYS” in the “3.
Pre-driving checks and adjustments” section.
Make sure that the mechanical key is removed
from the trunk pass-through lid key cylinder
before opening or closing the lid. Otherwise the
lid and the rear armrest may be damaged. PRECAUTIONS ON SEAT BELT USAGE If you are wearing your seat belt properly
adjusted, and you are sitting upright and well
back in your seat with both feet on the floor,
your chances of being injured or killed in an
accident and/or the severity of injury may be
greatly reduced. INFINITI strongly encourages
you and all of your passengers to buckle up
every time you drive, even if your seating
position includes a supplemental air bag.
Most U.S. states and Canadian provinces or ter-
ritories specify that seat belts be worn at all
times when a vehicle is being driven.SSS0678 SSS0677
SEAT BELTS
1-12 Safety — Seats, seat belts and supplemental restraint system
 —
—
10/12/09—tbrooks


Fastening the seat belts 1. Adjust the seat. (See “SEATS” earlier in
this section.)
2. Slowly pull the seat belt out of the retrac-
tor and insert the tongue into the buckle
until you hear and feel the latch engage.
● The retractor is designed to lock during a
sudden stop or on impact. A slow pulling mo-
tion permits the belt to move, and allows you
some freedom of movement in the seat.
● If the seat belt cannot be pulled from its fully
retracted position, firmly pull the belt and
release it. Then smoothly pull the belt out of
the retractor. 3. Position the lap belt portion low and snug
on the hips as shown.
4. Pull the shoulder belt portion toward the
retractor to take up extra slack. Be sure
the shoulder belt is routed over your
shoulder and across your chest.
The three-point type seat belts have two modes
of operation:
● Emergency Locking Retractor (ELR)
● Automatic Locking Retractor (ALR)
The Emergency Locking Retractor (ELR) mode
allows the seat belt to extend and retract to
allow the driver and passengers some freedom of movement in the seat. The ELR locks the seat
belt when the vehicle slows down rapidly or
during impacts.
The Automatic Locking Retractor (ALR) mode
(child restraint mode) locks the seat belt for
child restraint installation.
When the ALR mode is activated the seat belt
cannot be extended again until the seat belt
tongue is detached from the buckle and fully
retracted. The seat belt returns to the ELR mode
after the seat belt fully retracts. For additional
information, see “CHILD RESTRAINTS” later in
this section.
The ALR mode should be used only for child
restraint installation. During normal seat belt
use by an occupant, the ALR mode should not be
activated. If it is activated, it may cause uncom-
fortable seat belt tension.
WARNINGWhen fastening the seat belts, be certain that
seatbacks are completely secured in the
latched position. If they are not completely se-
cured, passengers may be injured in an acci-
dent or sudden stop.SSS0292 SSS0290
Safety — Seats, seat belts and supplemental restraint system
1-17
 —
—
10/12/09—tbrooks


Unfastening the seat belts To unfasten the seat belt, push the button on
the buckle. The seat belt automatically retracts.
Checking seat belt operation Seat belt retractors are designed to lock seat
belt movement by two separate methods:
● When the belt is pulled quickly from the
retractor.
● When the vehicle slows down rapidly. To increase your confidence in the seat belts,
check the operation as follows:
● Grasp the shoulder belt and pull forward
quickly. The retractor should lock and re-
strict further belt movement.
If the retractor does not lock during this check
or if you have any question about seat belt
operation, see an INFINITI retailer.
Center of rear seat (Sedan) Selecting correct set of seat belts :
The center seat belt buckle is identified by the
CENTER mark
 A
. The center seat belt tongue
can be fastened only into the center seat belt
buckle.SSS0326 SSS0687
1-18 Safety — Seats, seat belts and supplemental restraint system
 —
—
10/12/09—tbrooks


Shoulder belt height adjustment (for
Sedan front seats) The shoulder belt anchor height should be
adjusted to the position best for you. (See
“PRECAUTIONS ON SEAT BELT USAGE” earlier in
this section.)
To adjust, push the button
 A
, and then move
the shoulder belt anchor to the desired posi-
tion, so that the belt passes over the center of
the shoulder. The belt should be away from
your face and neck, but not falling off of your
shoulder. Release the adjustment button to lock
the shoulder belt anchor into position. WARNING● After adjustment, release the adjustment
button and try to move the shoulder belt
anchor up and down to make sure it is se-
curely fixed in position.
● The shoulder belt anchor height should be
adjusted to the position best for you. Failure
to do so may reduce the effectiveness of the
entire restraint system and increase the
chance or severity of injury in an accident.
Shoulder belt arm (for Coupe front
seats) Before fastening the seat belt, pull the shoulder
belt arm forward until it clicks at the lock
position. The arm can also be folded down for
easier access for rear seat passengers.
Pulling the arm forward will allow an easy
access to the belt.SSS0294A SSS0588
Safety — Seats, seat belts and supplemental restraint system
1-19
 —
—
10/12/09—tbrooks


● INFINITI recommends that child restraints be
installed in the rear seat. However, if you
must install a rear-facing child restraint in
the front passenger seat, move the passen-
ger seat to the rearmost position. Also, be
sure the front passenger air bag status light
is illuminated to indicate the passenger air
bag is OFF. See “Front passenger air bag and
status light” later in this section for details.
● The three-point seat belt in your vehicle is
equipped with an Automatic Locking Retrac-
tor (ALR) which must be used when installing
a child restraint.
● Failure to use the ALR will result in the child
restraint not being properly secured. The re-
straint could tip over or otherwise be unse-
cured and cause injury to the child in a sud-
den stop or collision.
● A child restraint with a top tether strap
should not be used in the front passenger
seat.
The instructions in this section apply to child
restraint installation using the vehicle seat
belts in the rear seat or the front passenger
seat. Front-facing Follow these steps to install a front-facing child
restraint using the vehicle seat belt in the rear
seat or in the front passenger seat:
1. If you must install a child restraint in the
front seat, it should be placed in a front-
facing direction only. Move the seat to the
rearmost position. Child restraints for in-
fants must be used in the rear-facing direc-
tion and therefore must not be used in the
front seat. 2. Position the child restraint on the seat.
Always follow the child restraint manufac-
turer’s instructions.
The back of the child restraint should be
secured against the seatback.
If necessary, adjust or remove the head
restraint (front passenger seat only) to ob-
tain the correct child restraint fit. (See
“HEAD RESTRAINTS” earlier in this section.)
If the head restraint is removed, store it in a
secure place. Be sure to reinstall the head
restraint when the child restraint is re-
moved.
If the seating position does not have an
adjustable head restraint and it is interfer-
ing with the proper child restraint fit, try
another seating position or a different child
restraint.Front-facing (front passenger seat) — step 1 SSS0640
1-30 Safety — Seats, seat belts and supplemental restraint system
 —
—
10/12/09—tbrooks


3. Route the seat belt tongue through the
child restraint and insert it into the buckle
until you hear and feel the latch engage.
Be sure to follow the child restraint manu-
facturer’s instructions for belt routing. 4. Pull the shoulder belt until the belt is fully
extended. At this time, the seat belt re-
tractor is in the Automatic Locking Retrac-
tor (ALR) mode (child restraint mode). It
reverts to Emergency Locking Retractor
(ELR) mode when the seat belt is fully
retracted. 5. Allow the seat belt to retract. Pull up on
the shoulder belt to remove any slack in
the belt.Front-facing — step 3 SSS0360B
Front-facing — step 4 SSS0651
Front-facing — step 5 SSS0652
Safety — Seats, seat belts and supplemental restraint system
1-31
 —
—
10/12/09—tbrooks


6. Remove any additional slack from the
seat belt; press downward and rearward
firmly in the center of the child restraint
with your knee to compress the vehicle
seat cushion and seatback while pulling
up on the seat belt.
7. If the child restraint is equipped with a
top tether strap, route the top tether strap
and secure the tether strap to the tether
anchor point (rear seat installation only).
(See “TOP TETHER STRAP CHILD RE-
STRAINT” earlier in this section.) Do not
install child restraints equipped with a
top tether strap to seating positions that
do not have a top tether anchor. 8. After attaching the child restraint, test it
before you place the child in it. Push it
from side to side while holding the seat
near the seat belt path. The child restraint
should not move more than 1 inch (25
mm) from side to side. Try to tug it
forward and check to see if the belt holds
the restraint in place. If the restraint is
not secure, tighten the belt as necessary,
or put the restraint in another seat and
test it again. You may need to try a
different child restraint. Not all child re-
straints fit in all types of vehicles.
9. Check that the retractor is in the ALR
mode by trying to pull more seat belt out
of the retractor. If you cannot pull any
more belt webbing out of the retractor,
the retractor is in the ALR mode.
10. Check to make sure the child restraint is
properly secured prior to each use. If the
seat belt is not locked, repeat steps 3
through 8.Front-facing — step 6 SSS0653
Front-facing — step 8 SSS0641
1-32 Safety — Seats, seat belts and supplemental restraint system
 —
—
10/12/09—tbrooks


3. Pull the shoulder belt until the belt is fully
extended. At this time, the seat belt re-
tractor is in the Automatic Locking Retrac-
tor (ALR) mode (child restraint mode). It
reverts to Emergency Locking Retractor
(ELR) mode when the seat belt is fully
retracted. 4. Allow the seat belt to retract. Pull up on
the shoulder belt to remove any slack in
the belt. 5. Remove any additional slack from the
child restraint; press downward and rear-
ward firmly in the center of the child
restraint with your hand to compress the
vehicle seat cushion and seatback while
pulling up on the seat belt.Rear-facing — step 3 SSS0655
Rear-facing — step 4 SSS0656
Rear-facing — step 5 SSS0657
1-34 Safety — Seats, seat belts and supplemental restraint system
 —
—
10/12/09—tbrooks