brake INFINITI G37 2012 User Guide

Black plate (97,1)
[ Edit: 2012/ 1/ 17 Model: V36-D ]. Malfunction indicator light blinking —
An engine misfire has been detected
which may damage the emission con-
trol system.
To reduce or avoid emission control
system damage:
1) Do not drive at speeds above 45
MPH (72 km/h).
2) Avoid hard acceleration or decelera-
tion.
3) Avoid steep uphill grades.
4) If possible, reduce the amount of
cargo being hauled or towed.
The malfunction indicator light may
stop blinking and remain on.
Have the vehicle inspected by an
INFINITI retailer. You do not need to
have your vehicle towed to the retailer.
CAUTIONContinued vehicle operation without having
the emission control system checked and
repaired as necessary could lead to poor
driveability, reduced fuel economy, and
possible damage to the emission control
system. Security indicator light GUID-99C24DC6-544D-45AC-90DB-96CA87927F70
The light blinks when the ignition switch is
in the ACC, OFF or LOCK position. This
function indicates the security system
equipped on the vehicle is operational.
If the security system is malfunctioning,
this light will remain on while the ignition
switch is in the ON position. For additional
information, see “ Security systems ” (P.2-
28).
Turn signal/hazard indicator
lights GUID-43A6DFE4-0C5C-4670-8FA3-F545A4863F5C
The light flashes when the turn signal
switch lever or hazard switch is turned on.
Vehicle Dynamic Control (VDC)
off indicator light GUID-A3E5746E-A6AD-4CFD-BF58-F2861559DFFC
The light comes on when the vehicle
dynamic control off switch is pushed to
OFF. This indicates that the vehicle dynamic
control system and traction control system
are not operating. AUDIBLE REMINDERS GUID-41C4B23E-C45A-494B-A7CD-10E6C3CED223
Key reminder chime GUID-CF2F9D77-25F2-40E6-8D1D-517CC8383919
A chime will sound if the driver side door is
opened while the ignition switch is pushed
to the ACC position or pushed to the OFF or
LOCK position with the Intelligent Key left
in the Intelligent Key port. Make sure the
ignition switch is pushed to the OFF
position, and take the Intelligent Key with
you when leaving the vehicle.
Light reminder chime GUID-EB436840-830A-402A-A3BA-8D5BCF0162C6
A chime will sound when the driver side
door is opened with the light switch in the
or position and the ignition switch
in the ACC, OFF or LOCK position.
Turn the light switch off when you leave the
vehicle.
Parking brake reminder chime GUID-44BA1A13-88DD-4711-BED2-C34A1A0970D0
The parking brake reminder chime will
sound if the vehicle is driven at more than
4 MPH (7 km/h) with the parking brake
applied. Stop the vehicle and release the
parking brake.
Instruments and controls
2-19

Black plate (98,1)
[ Edit: 2012/ 1/ 17 Model: V36-D ]2-20 Instruments and controlsBrake pad wear warning GUID-81F808C9-7883-4A77-9A99-E419C8DD7136
The disc brake pads have audible wear
warnings. When a brake pad requires
replacement, it will make a high pitched
scraping sound when the vehicle is in
motion. This scraping sound will first occur
only when the brake pedal is depressed.
After more wear of the brake pad, the
sound will always be heard even if the
brake pedal is not depressed. Have the
brakes checked as soon as possible if the
warning sound is heard. GUID-A0B240BC-9033-4FA8-8F5D-92CD638E559B
SIC4293
The dot matrix liquid crystal display
* 1
is
located between the tachometer and the
speedometer, and it displays the auto-
matic transmission position indicator (if so
equipped), the Intelligent Cruise Control
(ICC) system (if so equipped) information,
the Intelligent Key operation information
and other warnings and information.
For details about the automatic transmis-
sion position indicator, see “ Indicator
lights ” (P.2-18). For details about the ICC
system, see “ Intelligent Cruise Control
(ICC) system ” (P.5-23). For the details about
the Intelligent Key system, see “ Intelligent
Key system ” (P.3-7).DOT MATRIX LIQUID CRYSTAL DISPLAY

Black plate (100,1)
[ Edit: 2012/ 1/ 17 Model: V36-D ]2-22 Instruments and controlsINDICATORS FOR OPERATION GUID-3F80C245-4DDE-4CCD-9BA2-FE533BE15F57
1. Engine start operation indicator
(Automatic Transmission models) GUID-865F0D42-3E6C-4071-B120-AFF1A5EE4D2E
This indicator appears when the selector
lever is in the P (Park) position.
This indicator means that the engine will
start by pushing the ignition switch with
the brake pedal depressed.
2. Intelligent Key insertion indicator GUID-581E65CB-42A3-471E-923A-B9CDD6DBCCC9
This indicator appears when the Intelligent
Key needs to be inserted into the Intelli-
gent Key port. (For example, the Intelligent
Key battery is discharged.)
If this indicator appears, insert the Intelli-
gent Key into the Intelligent Key port in the
correct direction. (See “ Push-button igni-
tion switch ” (P.5-9).)
3. Intelligent Key removal indicator GUID-0F76AEA4-8CB1-4BBC-A994-137701CB6218
This indicator appears when the driver ’ s
door is opened with the ignition switch in
the OFF or LOCK position and the Intelli-
gent Key placed in the Intelligent Key port.
A key reminder chime also sounds.
If this indicator appears, remove the
Intelligent Key from the Intelligent Key port
and take it with you when leaving the vehicle.
4. NO KEY warning GUID-B266EC58-8CB6-45C9-B5B7-7FF3A17CB567
This warning appears in either of the
following conditions.
No key inside the vehicle: GUID-D73A39BF-43C8-459F-9C24-47B7F579C407
The warning appears when the door is
closed with the Intelligent Key left outside
the vehicle and the ignition switch in the
ACC or ON position. Make sure that the
Intelligent Key is inside the vehicle.
Unregistered Intelligent Key: GUID-D73A39BF-43C8-459F-9C24-47B7F579C407
The warning appears when the ignition
switch is pushed from the LOCK position
and the Intelligent Key cannot be recog-
nized by the system. You cannot start the
engine with an unregistered key. Use the
registered Intelligent Key.
See “ Intelligent Key system ” (P.3-7) for
more details.
5. SHIFT “ P ” warning (Automatic
Transmission models) GUID-9BDEFCBE-BD2F-42CF-B3EF-1A2E660B253C
This warning appears when the ignition
switch is pushed to stop the engine with
the selector lever in any position except
the P (Park) position.
If this warning appears, move the selector lever to the P (Park) position or push the
ignition switch to the ON position.
An inside warning chime will also sound.
(See “ Intelligent Key system ” (P.3-7).)
6. “ PUSH ” warning (Automatic
Transmission models) GUID-C4F385F1-244F-4AA8-A2FB-F05B8CE33F2B
This warning appears when the selector
lever is moved to the P (Park) position with
the ignition switch in the ACC position after
the SHIFT “ P ” warning appears.
To push the ignition switch to the OFF
position, perform the following procedure:
SHIFT “ P ” warning ? (Move the selector
lever to “ P ” ) ? PUSH warning ? (Push the
ignition switch ? ignition switch position
is turned to ON) ? PUSH warning ? (Push
the ignition switch ? ignition switch
position is turned to OFF)
7. Intelligent Key battery discharge
indicator GUID-27367EF5-F931-4EBC-8576-1379DE51DE47
This indicator appears when the Intelligent
Key battery is running out of power.
If this indicator appears, replace the
battery with a new one. (See “ Intelligent
Key battery replacement ” (P.8-26).)

Black plate (101,1)
[ Edit: 2012/ 1/ 17 Model: V36-D ]8. Engine start operation indicator
(Manual Transmission models) GUID-6F348F29-B160-4632-B05C-A45F6D5E7AD7
This indicator means that the engine will
start by pushing the ignition switch with
the clutch pedal depressed.
9. Parking brake release warning GUID-7289EFE7-F400-4C19-9597-F8AA159911CA
This warning appears when the vehicle
speed is above 4 MPH (7 km/h) and the
parking brake is applied.
10. Low fuel warning GUID-2FE47C40-46BC-4EC8-AC52-E90EBB5F8B0F
This warning appears when the fuel level in
the tank is getting low. Refuel as soon as it
is convenient, preferably before the fuel
gauge reaches the empty (E) position.
There is a small reserve of fuel remaining
in the tank when the fuel gauge reaches
the empty (E) position.
11. Low washer fluid warning GUID-54C94524-E0BC-4326-8A11-B2CD705757A6
This warning appears when the washer
tank fluid is at a low level. Add washer fluid
as necessary. (See “ Window washer fluid ”
(P.8-16).)
12. Door/trunk open warning (igni-
tion switch is in the ON position) GUID-50585695-BAF8-48B7-8A81-CEA312693DE1
This warning appears if any of the doors and/or the trunk lid are open or not closed
securely. The vehicle icon indicates which
door or the trunk lid is open on the display.
13. Loose fuel cap warning GUID-479E9C15-B26C-477B-8AA7-ED29D6CD76ED
This warning appears when the fuel-filler
cap is not tightened correctly after the
vehicle has been refueled. (See “ Fuel-filler
door ” (P.3-23).)
14. Check tire pressure warning GUID-174D3E5C-C80F-432A-944F-EE13C51D1486
This warning appears when the low tire
pressure warning light in the meter illumi-
nates to indicate the low tire pressure. If
this warning appears, stop the vehicle and
adjust the tire pressure to the recom-
mended COLD tire pressure shown on the
Tire and Loading Information label. (See
“ Low tire pressure warning light ” (P.2-15)
and “ Tire Pressure Monitoring System
(TPMS) ” (P.5-4).)
15. “ Time to rest ” indicator GUID-9639DC97-247E-4499-BA1B-AFF133E94400
This indicator appears when the set “ time
to rest ” indicator activates. You can set the
time for up to 6 hours. (See “ Trip
computer ” (P.2-26).) 16. Low outside temperature warn-
ing GUID-E9986E7D-DDA6-4BCF-8D8E-D8F9C645C41B
This warning appears if the outside tem-
perature is below 37 8 F (3 8 C). The warning
can be set not to be displayed. (See “ Trip
computer ” (P.2-26).)
17. Cruise indicator GUID-8437A118-88BE-4895-A266-56D415AE4EC7
Cruise main switch indicator: GUID-D73A39BF-43C8-459F-9C24-47B7F579C407
The indicator is displayed when the cruise
control main switch is pushed. When the
main switch is pushed again, the indicator
disappears. When the cruise control main
switch indicator is displayed, the cruise
control system is operational.
Cruise set switch indicator: GUID-D73A39BF-43C8-459F-9C24-47B7F579C407
The indicator is displayed while the vehicle
speed is controlled by the cruise control
system. If the indicator blinks while the
engine is running, it may indicate that the
cruise control system is not functioning
properly. Have the system checked by an
INFINITI retailer.
See “ Cruise control ” (P.5-21) for details.
Instruments and controls
2-23

Black plate (115,1)
[ Edit: 2012/ 1/ 17 Model: V36-D ]Battery saver system GUID-015F3DAF-8A59-4727-BB76-C11FB41B2B60
A chime will sound when the driver side
door is opened with the light switch in the
or position and the ignition switch
in the ACC, OFF or LOCK position.
When the headlight switch is in the
or
position while the ignition switch is in
the ON position, the lights will automati-
cally turn off 5 minutes after the ignition
switch has been pushed to the OFF
position.
When the headlight switch remains in the
or position after the lights
automatically turn off, the lights will turn
on when the ignition switch is pushed to
the ON position.
CAUTION. When you turn on the headlight switch
again after the lights automatically turn
off, the lights will not turn off auto-
matically. Be sure to turn the light
switch to the OFF position when you
leave the vehicle for extended periods of
time, otherwise the battery will be
discharged. . Never leave the light switch on when the
engine is not running for extended
periods of time even if the headlights
turn off automatically.
Daytime running light system (Ca-
nada only) GUID-84A2F990-744E-4ADE-B431-E99613FFC97F
The daytime running lights automatically
illuminate when the engine is started with
the parking brake released. The daytime
running lights operate with the headlight
switch in the OFF position or in the
position. Turn the headlight switch to the
position when driving at night.
If the parking brake is applied before the
engine is started, the daytime running
lights do not illuminate. The daytime
running lights illuminate once the parking
brake is released. The daytime running
lights will remain on until the ignition
switch is pushed to the OFF position. SIC3257
Instruments and controls
2-37

Black plate (174,1)
[ Edit: 2012/ 1/ 17 Model: V36-D ]3-32 Pre-driving checks and adjustmentsBack on Exit ” key is turned to ON or OFF in
the “ Comfort ” settings. (See “ Vehicle
information and settings ” (P.4-9).)
Initialize entry/exit function GUID-0EEBBCEC-2899-4DC8-AE43-1CC42FE3C5C1
If the battery cable is disconnected, or if
the fuse opens, the entry/exit function will
not work though this function was set on
before. In such a case, after connecting the
battery or replacing with a new fuse, open
and close the driver ’ s door more than two
times after the ignition switch is turned
from the ON position to the LOCK position.
The entry/exit function will be activated. SPA2322
SEAT SYNCHRONIZATION FUNCTION GUID-44A9BCE7-C5A3-4DE5-84C7-DAFAF434BFA8
The seat synchronization function automa-
tically adjusts the positions of the steering
wheel and outside mirrors when the seat is
adjusted using the power seat switches.
However, the steering wheel and outside
mirrors will not move if the seat is adjusted
over the maximum thresholds. The system
considers that the steering wheel and
outside mirror adjustments are not neces-
sary because the seat may not be adjusted
for the driving position. Note that the
function is set to disabled as the factory
default setting. The seat synchronization function operates
under the following conditions:
. The ignition switch is in the ON posi-
tion.
. The selector lever is in the P (Park)
position (Automatic Transmission mod-
els) or the parking brake is applied
(Manual Transmission models).
. The seatback is raised (Coupe).
If the outside mirrors or the steering wheel
reaches its maximum adjustment, the
function is automatically disabled. Restart
the function by selecting a previously
stored seat memory position using the
memory switches (1 or 2). An Intelligent
Key that was previously linked to the
stored seat memory can also be used to
restart the function.
If a seat position was not previously stored
in the seat memory, restart the function by
adjusting the steering wheel and outside
mirrors manually for your best driving
position and then drive the vehicle above
4 MPH (7 km/h).

Black plate (175,1)
[ Edit: 2012/ 1/ 17 Model: V36-D ]Cancel or activate seat synchroni-
zation function GUID-9FA1381E-62FE-4338-8BE9-EF06F61AFC12
For Automatic Transmission models:
The selector lever must be in the P (Park)
position with the ignition switch in the ACC
position.
For Manual Transmission models:
The parking brake must be applied with
the ignition switch in the ACC position.
The seat synchronization function can be
activated or canceled by pushing and
holding the SET switch for more than 10
seconds while the ignition switch is in the
ACC position.
The indicator lights on the memory
switches (1 and 2) will blink once when
the function is canceled, and the indicator
lights will blink twice when the function is
activated. Note that the indicator lights
may illuminate after 5 seconds while
holding the SET switch. This indicates
readiness for linking the Intelligent Key to
a stored memory position. Keep the SET
switch pushed for more than 10 seconds to
turn on or off the seat synchronization
function. MEMORY STORAGE GUID-A3BE9A91-CE23-4574-92F2-3FB031E53D7E
Two positions for the driver ’ s seat, steering
column and outside mirrors can be stored
in the automatic drive positioner memory.
Follow these procedures to use the mem-
ory system.
1. Automatic transmission models:
Move the selector lever to the P (Park)
position.
Manual transmission models:
Apply the parking brake.
2. Raise the seatback (Coupe).
3. Push the ignition switch to the ON
position.
4. Adjust the driver ’ s seat, steering col-
umn and outside mirrors to the desired
positions by manually operating each
adjusting switch. For additional infor-
mation, see “ Seats ” (P.1-2) and “ Tilt/
telescopic steering ” (P.3-26) and “ Out-
side mirrors ” (P.3-29).
5. Push the SET switch and, within 5
seconds, push the memory switch (1
or 2) fully for at least 1 second.
The indicator light for the pushed
memory switch will stay on for approxi-
mately 5 seconds after pushing the switch.
If memory is stored in the same
memory switch, the previous memory
will be deleted.
Linking Intelligent Key to a stored
memory position GUID-260E8272-8777-4E19-9288-E40B723FABBA
The Intelligent Key can be linked to a
stored memory position with the following
procedure.
1. Follow the steps for storing a memory
position.
2. While the indicator light for the memory
switch being set is illuminated for 5
seconds, push the
button on the
Intelligent Key. If the indicator light
blinks, the Intelligent Key is linked to
that memory setting.
Push the ignition switch to the OFF posi-
tion, and then push the
button on the
Intelligent Key. The driver ’ s seat, steering
wheel and outside mirrors will move to the
memorized position.
Confirming memory storage GUID-E5D175B3-57DC-4C96-A449-0B72F25D2264
. Push the ignition switch to the ON
position and push the SET switch. If
the main memory has not been stored,
the indicator light will come on for
Pre-driving checks and adjustments
3-33

Black plate (176,1)
[ Edit: 2012/ 1/ 17 Model: V36-D ]3-34 Pre-driving checks and adjustmentsapproximately 0.5 second. When the
memory has stored in position, the
indicator light will stay on for approxi-
mately 5 seconds.
. If the battery cable is disconnected, or if
the fuse opens, the memory will be
canceled. In this case, reset the desired
position using the previous procedure.
. If optional Intelligent Keys are added to
your vehicle, the memory storage pro-
cedure to switch 1 or 2 and linking
Intelligent Key procedure to a stored
memory position should be performed
again for each Intelligent Key. For
additional Intelligent Key information,
see “ Keys ” (P.3-2).
Selecting the memorized position GUID-739A81F0-8862-49C2-BBA8-117F41F648F9
1. Automatic transmission models:
Move the selector lever to the P (Park)
position.
Manual transmission models:
Apply the parking brake.
2. Raise the seatback (Coupe).
3. Use one of the following methods to
move the driver ’ s seat, the outside
mirrors and the steering wheel. .
Push the ignition switch to the ON
position and push the memory
switch (1 or 2) fully for at least 1
second. .
Within 45 seconds of opening the
driver ’ s door, push the memory
switch (1 or 2) fully for at least 1
second.
The driver ’ s seat, steering column
and outside mirrors will move to the
memorized position with the indica-
tor light flashing, and then the light
will stay on for approximately 5
seconds.
For manual transmission models, the
memory positions can be selected even
when the engine is running. In this case,
move the shift lever to the N (Neutral)
position and apply the parking brake.
Then, perform step 2.
SYSTEM OPERATION GUID-0383C8BF-12F8-48D0-9B28-5A2A0DCC8D55
The automatic drive positioner system will
not work or will stop operating under the
following conditions:
. When the vehicle speed is above 4 MPH
(7 km/h).
. When the adjusting switch for the
driver ’ s seat and steering column is
turned on while the automatic drive positioner is operating.
. When the memory switch 1 or 2 is not
pushed for at least 1 second.
. When the seat, steering column and
outside mirrors have already been
moved to the memorized position.
. When no position is stored in the
memory switch.
. When the parking brake is released (MT
models).
. When the speed is above 4 MPH (7
km/h) while the parking brake is
applied (MT models).
To restart the drive positioner system,
move the parking brake to off and on.
. When the engine is started while
moving the automatic drive positioner.
. When the AT selector lever is moved
from the P (Park) position to any other
position. (However, it will not be
canceled if the switch is pushed while
the seat and steering column are
returning to the previous positions
(entry/exit function).)
. When the driver ’ s door remains open
for more than 45 seconds and the
ignition switch is not in the ON posi-
tion.

Black plate (181,1)
[ Edit: 2012/ 1/ 17 Model: V36-D ]GUID-B399574C-759D-4EDD-9D8B-240757C36DDF
WARNING. Do not disassemble or modify this
system. If you do, it may result in
accidents, fire, or electric shock.
. Do not use this system if you notice any
abnormality, such as a frozen screen or
lack of sound. Continued use of the
system may result in accident, fire or
electric shock.
. In case you notice any foreign object in
the system hardware, spill liquid on it,
or notice smoke or smell coming from it,
stop using the system immediately and
contact your nearest INFINITI retailer.
Ignoring such conditions may lead to
accidents, fire, or electric shock.
. Park the vehicle in a safe location and
apply the parking brake to view the
images on the front center display
screen.
Do not attempt to operate the system in
extreme temperature conditions [below
− 4 8 F ( − 20 8 C) and above 158 8 F (70 8 C)].
Operating this system under these condi-
tions may result in system malfunctions. GUID-7F90DABA-37C8-4571-9C5A-2974CEC5AA7A
SAA1523
Models with navigation system
1. “ STATUS ” status display button
(P.4-9)
2, 6, 7, 10, 11.
For navigation system control buttons
(Refer to the separate Navigation
System Owner ’ s Manual.)
3. INFINITI controller (P.4-5)
4. “ PHONE ” Bluetooth ®
Hands-Free
Phone System button (P.4-90)
5. “
OFF ” brightness control and
display ON/OFF button (P.4-9)
8. “ AM·FM·SAT ” band selector button
(P.4-41) 9. “ DISC·AUX ” selector button (P.4-41)
12. “ INFO ” vehicle and navigation infor-
mation button (P.4-9)
13. “ SETTING ” button (P.4-14)
Monitor, climate, audio, phone and voice recognition systems
4-3SAFETY NOTE CENTER MULTI-FUNCTION CONTROL PANEL

Black plate (200,1)
[ Edit: 2012/ 1/ 17 Model: V36-D ]4-22 Monitor, climate, audio, phone and voice recognition systems SAA2491
Image Viewer (models with naviga-
tion system) GUID-3A8CCE29-BAF6-4276-8E18-96A1950EFDF7
The image files in the USB memory will be
displayed. To display the Image Viewer,
push the SETTING button, select the
“ Other ” key and then select the “ Image
Viewer ” key. The image of the selected file
is displayed on the right side of the screen.
When a number of folders are included in
the USB memory, select a folder from the
list to display the file list.
Images will not be shown on the display
while the vehicle is in any drive position to
reduce driver distraction. To view images, stop the vehicle in a safe location and
apply the parking brake.
SAA2492
Full Screen Display: GUID-D73A39BF-43C8-459F-9C24-47B7F579C407
The full screen display will appear when
selecting the “ Full Screen Display ” key.
To operate the Image Viewer or to change
the settings, select the desired key using
the INFINITI controller.
.
(Start)
Select the “ ” key to start playing
the slideshow.
.
(Stop)
Select the “
” key to stop the
slideshow.
.
(Next)
Select the “ ” key to display the next